Pin styles S, N, F & G are compatible with the ModuMate interconnect system for socketing
and surface mounting
Not intended for socket or Surfmate mounting
Note:
Product images may not highlight current product markings.
VI-ARM™
Page 1 of 11
Rev 5.0
06/2019
VI-ARMx1xx
Electrical Characteristics
Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature, unless otherwise specified. All
temperatures refer to the operating temperature at the center of the baseplate. Specifications apply for AC mains having up to 5% total harmonic distortion.
Input Specifications
VI-ARM - 1
Parameter
Operating input voltage
Input undervoltage
Input surge withstand
AC line frequency
Input current, RMS
Power factor
47
47
0
0
0.60
Min
90
180
Typ
Max
132
264
90
280
63
880
7.4
5.4
47
47
0
0
0.60
Min
90
180
VI-ARMB - 2
Typ
Max
132
264
90
280
63
880
11.1
7.2
Unit
V
AC
V
AC
V
AC
V
AC
Hz
Hz
Amps
Amps
Notes
Autoranging (doubler mode)
Autoranging (bridge mode)
No damage
100ms
C, E-Grade
T & H-Grade
120V
AC
240V
AC
Dependent on line source
impedence, hold-up
capacitance, and load
30
2400
Amps
µF
264V
AC
peak line,
cold start
Inrush current
Hold-up Capacitance
30
1600
Output Specifications
VI-ARM - 1
Parameter
Output power
Efficiency
120V
AC
240 V
AC
Output voltage
Min
0
0
94
96
200
96
98
375
Typ
Max
500
750
Min
0
0
94
96
200
96
98
375
VI-ARMB - 2
Typ
Max
750
1500
Unit
Watts
Watts
%
%
V
DC
90 – 264V
AC
Notes
105 – 132V
AC
(Figure 1)
210 – 264V
AC
(Figure 2)
Control Pin Specifications
Parameter
AC Bus OK (B OK)
On-state resistance (low)
On-state current (low)
Off-state voltage
On-state threshold
Off-state threshold
Module Enable (EN)
On-state resistance (low)
On-state current (low)
Off-state voltage
On-state threshold
Off-state threshold
Overvoltage shut down
AC Bus OK - module enable,
differential error*
Min
Typ
Max
15
–50
16
245
210
15
50
16
245
195
400
16
Unit
Ω
mA
V
DC
V
DC
V
DC
Ω
mA
V
DC
V
DC
V
DC
V
DC
V
DC
AC Bus OK and module enable thresholds track
Notes
To negative output - bus normal
Bus normal
Bus abnormal, 27kΩ internal pull up to 15V
DC
(Figure 12)
Output bus voltage
Output bus voltage
To negative output - converters are disabled
150kΩ internal pull up to 15V
DC
(Figure 11)
Output bus voltage
Output bus voltage
12
235
200
14
240
205
12
235
185
380
12
14
240
190
390
14
* Tracking error between BUS OK and Enable thresholds
VI-ARM™
Page 2 of 11
Rev 5.0
06/2019
VI-ARMx1xx
Electrical Characteristics (Cont.)
Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature, unless otherwise specified. All
temperatures refer to the operating temperature at the center of the baseplate. Specifications apply for AC mains having up to 5% total harmonic distortion.
Continuing from the previous post, where do I get my SD sensor data? - STMicroelectronics AMG SensorTile Development Competition - Electronic Engineering World - Forum [url=https://bbs.eeworld.com.cn/...
It has been a while since I received the board. Yesterday, I was preparing to measure the power consumption and analyze how this board achieves low power consumption. As a result, I was stunned when I...
At first glance, I thought it was NI, and I thought NI had released a development board, haha. I saw the forum activity and found that the circuit board has multiple outputs, so I couldn't wait to app...
The nRF52832 system-on-chip has ultra-low power consumption and extremely high design flexibility. It can support a variety of wireless communication protocols and is very powerful. It is very suitabl...
International Solar Photovoltaic Network News: Chinese inverter company Sungrow announced that it will build a 3GW photovoltaic inverter manufacturing plant in Bangalore, the capital of Karnataka, ...[Details]
In the war without gunpowder between China and the United States,
ZTE
has become a new victim. The seven-year chip ban by the United States has pushed this communications giant to a life-or...[Details]
After searching a lot of information, I finally understood the time base timer. I did not use any library functions but operated the registers directly. The following introduces the systick in STM32...[Details]
China Energy Storage Network News:
The State Grid Corporation of China, this elephant, is planning to turn around and enter the emerging power service market.
The rallying cry for the tr...[Details]
With the development of information technology, intelligence, informatization and networking have become the development trend of modern industrial control. Since the 1980s, the rapid development...[Details]
Site conditions: 1. AD acquisition, DMA transmission; AD is set to single-channel continuous mode, DMA is set to single-shot mode. The upper threshold of the AD analog watchdog setting is less than t...[Details]
Use the STM32 timer input capture module to control 3-way ultrasonic sensors. The ultrasonic sensor used this time is the common HC-SR04, which is often used in the obstacle avoidance system of smal...[Details]
ADC: 1. The ADC module inside STM32 has three ADC1, ADC2, and ADC3, which are independent of each other, so synchronous sampling can be performed. 2ADC input clock must not exceed 14MHz, it is genera...[Details]
(1) JTAG is a communication standard used for real-time and fast communication between computers and microcontrollers. The JTAG function of AVR (only available on some models) makes AVR debugging ver...[Details]
Take serial port interrupt as an example: like: void serial() interrupt 4 { } and void serial_uart() interrupt 4 { } The functions of both functions are to define the serial port interrupt function. ...[Details]
According to Kyodo News, Japan's NTT Institute for Physical Science and others announced on November 20 that they had successfully developed a new ultra-high-performance
quantum computer
th...[Details]
According to the design requirements, the maximum voltage gain ≥ 60dB is achieved within a wide signal bandwidth (0-10MHz), and the ability to continuously adjust the gain or preset the gain in 5dB...[Details]