CRA06P
www.vishay.com
Vishay
Thick Film Chip Resistor Array
FEATURES
• Concave terminal array with square corners
• 4 and 8 terminal package with isolated resistors
• Wide ohmic range: 10R to 1M0
• AEC-Q200 qualified
CRA06P thick film resistor array is constructed on a high
grade ceramic body with concave terminations. A small
package enables the design of high density circuits. The
single component reduces board space, component counts
and assembly costs.
• Material categorization: for definitions of compliance
please see
www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
CIRCUIT
POWER RATING
P
70 °C
W
0.063
LIMITING ELEMENT
VOLTAGE MAX.
V
50
TEMPERATURE
COEFFICIENT
±
ppm/K
100
200
TOLERANCE
±
%
1
2; 5
RESISTANCE
RANGE
10 to 1M
E-SERIES
24 + 96
24
CRA06P
03
Zero-Ohm-Resistor:
R
max.
= 50 m,
I
max.
= 1 A
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
CRA06P
03 CIRCUIT
Rated dissipation at 70 °C
(2)
W per element
0.063
(1)
Limiting element voltage
V
50
Insulation voltage (1 min)
V
DC/AC
peak
100
Category temperature range
°C
-55 to +155
Insulation resistance
> 10
9
Notes
(1)
Rated voltage:
P
x
R
(2)
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: CRA06P08347K0JTA
(1)
C
R
A
TERMINAL
STYLE
P
0
6
P
0
8
3
4
7
K
0
J
T
A
MODEL
CRA06
PIN
04
08
CIRCUIT
3
= 03
VALUE
R
= decimal
K
= thousand
M
= million
0000
= 0
jumper
473
TOLERANCE
F
=±1%
G
=±2%
J
=±5%
Z
= 0
jumper
J
TOLERANCE
F
=±1%
G
=±2%
J
=±5%
Z
= 0
jumper
PACKAGING
(2)
TA
TC
SPECIAL
Up to 2 digits
Product Description: CRA06P 08 03 473 J RT1 e3
CRA06P
MODEL
CRA06P
08
TERMINAL COUNT
04
08
03
CIRCUIT TYPE
03
RT1
PACKAGING
(4)
RT1
RT6
e3
LEAD (Pb)-FREE
e3
= pure tin
termination finish
RESISTANCE VALUE
473
= 47 k
4702
= 47 k
10R0
= 10
100
= 10
000
= 0
jumper
First two digits (3 for 1 %)
are significant. Last digit
is the multiplier.
(1)
(2)
Notes
Preferred way for ordering products is by use of the PART NUMBER
Please refer to the table PACKAGING, see next page
Document Number: 31047
1
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Revison: 23-Feb-17
CRA06P
www.vishay.com
Vishay
PACKAGING CODE
PACKAGING
MODEL
TAPE WIDTH
DIAMETER
PITCH
PIECES/REEL
PART NUMBER
180 mm/7"
CRA06P
8 mm
330 mm/13"
4 mm
20 000
TC
RT6
4 mm
5000
TA
PAPER TAPE
PRODUCT DESCRIPTION
RT1
CIRCUIT
DERATING
Rated Power in %
120
100
03 CIRCUIT
80
60
40
20
0
- 55
4 pin
8
pin
- 25
0
25
50
75
70
100
125
155 175
Ambient Temperature in °C
DIMENSIONS
PIN
NO#
DIMENSIONS
in millimeters
L
1.60
3.20
A
0.30
0.30
B
0.40
0.40
C
0.40
0.40
P
0.80
0.80
-
T
0.60
0.60
W
1.60
1.60
A
w
C
4
8
Tol.
± 0.20 ± 0.20 ± 0.15 ± 0.20
± 0.10 ± 0.15
P
L
B
T
SOLDER PAD DIMENSIONS
in millimeters
c
c
w
w
2.6
p
0.8
a
0.4
b
0.9
WAVE
0.8
b
p
a
Revison: 23-Feb-17
Document Number: 31047
2
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
CRA06P
www.vishay.com
Vishay
EN 60115-1
TEST PROCEDURES AND REQUIREMENTS
REQUIREMENTS
PERMISSIBLE CHANGE (R/R)
(1)
STABILITY
CLASS 1 OR BETTER
CRA06P
Resistance (4.5)
Temperature coefficient (4.8.4.2)
Overload (4.13)
Solderability (4.17.5)
(2)
TEST
(clause)
CONDITIONS OF TEST
STABILITY
CLASS 2 OR BETTER
10
to 1 M
± 2 %; ± 5 %
± 200 ppm/K
± (0.5 %
R
+ 0.05
)
Stability for product types:
-
(20 / -55 / 20) °C and
(20 / 125 / 20) °C
U
= 2.5 x (P
70
x
R)
1/2
2 x
U
max.
; 0.5 s
Aging 4 h at 155 °C, dryheat
Solder bath method; 235 °C; 2 s
Visual examination
Solder bath method;
(260 ± 5) °C; (10 ± 1) s
30 min at LCT = -55 °C;
30 min at UCT = 125 °C; 5 cycles
(40 ± 2) °C; 56 days;
(93 ± 3) % RH
16 h at UCT = 125 °C; 1 cycle at 55 °C;
2 h at LCT = -55 °C;
1 h/1 kPa at 15 °C to 35 °C;
5 cycles at 55 °C
U
= (P
70
x
R)
1/2
U
=
U
max.
; whichever is less severe
U
= (P
70
x
R)
1/2
U
=
U
max.
; whichever is less severe
1.5 h “ON”; 0.5 h “OFF”;
70 °C; 1000 h
Duration extended to 8000 h
UCT = 125 °C; 1000 h
10
to 1 M
±1%
± 100 ppm/K
± (0.25 %
R
+ 0.05
)
Good tinning ( 95 % covered)
no visible damage
± (0.25 %
R
+ 0.05
)
± (0.25 %
R
+ 0.05
)
± (1 %
R
+ 0.05
)
± (0.5 %
R
+ 0.05
)
± (0.5 %
R
+ 0.05
)
± (2 %
R
+ 0.1
)
Resistance to soldering heat (4.18.2)
Rapid change of temperature (4.19)
Damp heat, steady state (4.24)
Climatic sequence (4.23)
± (1 %
R
+ 0.05
)
± (2 %
R
+ 0.1
)
Endurance at 70 °C (4.25.1)
Extended endurance (4.25.1.8)
Endurance at upper category
temperature (4.25.3)
± (1 %
R
+ 0.05
)
± (2 %
R
+ 0.1
)
± (1 %
R
+ 0.05
)
± (2 %
R
+ 0.1
)
± (4 %
R
+ 0.1
)
± (2 %
R
+ 0.1
)
Notes
(1)
Figures are given for a single element
(2)
Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years
APPLICABLE SPECIFICATIONS
• EN 60115-1
• EN 140400
• EN 140401-802
• IEC 60068-2-X
• EIA 481
Generic specification
Sectional specification
Detail specification
Variety of environmental test procedures
Packaging of SMD components
Revison: 23-Feb-17
Document Number: 31047
3
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 08-Feb-17
1
Document Number: 91000
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Vishay
:
CRA06P0832K20JTA CRA06P083680RJTA CRA06P08315R0JTA CRA06P08333R0JTA CRA06P08315K0JTA
CRA06P083100RJTA CRA06P08310K0JTA CRA06P0833K30JTA CRA06P0831K00JTA CRA06P0834K70JTA
CRA06P08328R0JTA CRA06P08322R0JTA CRA06P08333R2FTA CRA04P08035R10JRT7 CRA04P08037R50JRT7
CRA06P0803470JRT1 CRA06P08347K0JTA CRA06P083470KJTA CRA06P080349R9FRT1 CRA04P08310R0JTD
CRA06P083100KJTA CRA06P083120KJTA CRA06P083150RJTA CRA06P083180RJTA CRA06P08327K0JTA
CRA06P0832K70JTA CRA06P083330KJTA CRA06P08333K0JTA CRA06P08347R0JTA CRA06P08356R0JTA
CRA06P0835K60JTA CRA06P08310K0FTA CRA06P08322R0FTA CRA06P08349R9FTA CRA06P08339R2FTA
CRA06P083499RFTA CRA06P08351R0FTA CRA06P083698RFTA CRA06P083845RFTA
京公网安备 11010802033920号
EEWORLD
