TVS diode 1.5SMC110A/1.5SMC110CA, SMC/DO-214AB package, peak pulse power 1500W, used in overvoltage protection of sensitive electronic parts, covering automotive electronics, consumer electronics, industrial equipment, household appliances, communication equipment and other fields.
TVS diode 1.5SMC110A/1.5SMC110CA, SMC/DO-214AB package, peak pulse power 1500W, used in overvoltage protection of sensitive electronic parts, covering automotive electronics, consumer electronics, industrial equipment, household appliances, communication equipment and other fields.
I used C2000's SPI to drive ADS8332. I've had success in the past, but it was on a different PCB. However, when I tried it again, I ran into a lot of problems. [/font] Phenomenon: When the sampling an...
Question 1: Is it necessary to install the initial value of the timer in the main function? I seem to have tried it and it works fine without it. Question 2: If timer 0 is turned off in timer 1, do I ...
When I assign a 20-bit address 0x10000 to a pointer variable, it always says that it is out of the range of 0 to 0xFFFF.This is possible in assembly language, because MSP430X provides instructions wit...
Please help me analyze this:the crystal oscillator is not working properly. It does not oscillate at first. Then I touch it with a soldering iron and it works normally for a while. Then it does not os...
As the title says. Now the program runs in pure DOS booted by virtual floppy drive. The program written in 2000 with bc31 runs smoothly in 2000, but it is very stuck in DOS. I want to compile it in DO...
Recently, the U.S. Department of Commerce announced that it would prohibit companies in the country from selling any electronic technology or communication components to ZTE, a Chinese communicatio...[Details]
ZTE,
caught
in the vortex of
the US ban on the sale
of chips
, has sounded the alarm for China's information technology industry and revealed China's "chip disease". Let's follow the ...[Details]
1.MAX31865 (1 Introduction The MAX31865 is an easy-to-use thermistor-to-digital converter optimized for platinum resistance temperature detectors (RTDs). External resistors set the RTD sensitivity, a...[Details]
1. Function prototype In the function library officially provided by STM32, you can find functions like HAL_Delay(). This function uses a timer to achieve a more accurate time delay and provides it...[Details]
Using Systick timer to achieve delay 1. SysTick timer characteristics The SysTick timer is a 24-bit down counter, that is, when vlue is decremented to 0, an interrupt is triggered and the load va...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
Analysts have sorted out some interesting phenomena. Let's follow the embedded editor to learn about the relevant content.
Huawei emerged as a star in the all-
flash
array sales ra...[Details]
With the development of the automobile industry, more and more automotive electronic components are being used in modern cars, providing better safety, comfort and economy for cars. In the past, cars...[Details]
If you do not use an external crystal on the STM32, the connection method of OSC_IN and OSC_OUT If you use the internal RC oscillator instead of an external crystal, please follow the following metho...[Details]
1) ADC multi-channel acquisition: (Multi-channel acquisition must use scanning mode. In scanning mode, the channels of the rule group share a register, so DMA transmission must be used; to prevent da...[Details]
DMA： 1. When using DAC, when the converted analog signal is output through the IO port, why is the IO port also configured to input mode? PS: The stm32 manual defines that PA4 and PA5 are connected...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
The following comes from - "cortex-M3 Definitive Guide" Special function register group: Program Status Registers (PSRs or xPSRs) Interrupt mask register group (PRIMASK, FAULTMASK, and BASEPRI) ...[Details]
China Energy Storage Network News:
2017 is the year when China's energy internet policy was implemented. Since the National Energy Administration issued the "Notice on the Announcement of the...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
