input protection. It drives an external N-channel MOSFET
to replace a power Schottky diode. Its very low quiescent
current and fast transient response meet the tough require-
ments in automotive applications where AC input signals
of up to 100kHz are present. These signals are rectified
with minimum power dissipation on the external FET,
simplifying thermal management on the PCB.
With a drop of only 20mV, the LT8672 solution eases the
minimum input voltage requirement during cold crank
and start-stop, allowing simpler and more efficient cir-
cuits. If the input power source fails or is shorted, a fast
turn-off minimizes reverse current transients. An available
shutdown mode reduces the quiescent current to 3.5μA.
An integrated auxiliary boost regulator provides the re-
quired boost voltage to turn the external FET fully on. A
power good pin signals when the external FET is ready to
take load current.
L,
LT, LTC, LTM, Linear Technology, the Linear logo and Silent Switcher are registered
trademarks of Analog Devices, Inc. All other trademarks are the property of their respective
owners.
n
n
n
n
n
n
Reverse Input Protection to –40V
Improved Performance Compared to a
Schottky Diode:
n
Reduce Power Dissipation by >90%
n
Reduce Drop to 20mV
Ultrafast Transient Response
n
Rectifies 6V
P-P
Up to 50kHz
n
Rectifies 2V
P-P
Up to 100kHz
Wide Operating Voltage Range: 3V to 42V
Low 20µA Quiescent Current in Operation
Low 3.5µA Shutdown Current
Accurate 1.21V Enable Pin Threshold
Available in Small 10-Lead MSOP
APPLICATIONS
n
n
n
Automotive Battery Protection
Industrial Supplies
Portable Instrumentation
TYPICAL APPLICATION
12V, 5A Automotive Reverse Battery Protection
V
BATT
12V
SMBJ33A
33V
SMBJ15A
SOURCE GATE DRAIN AUX
15V
LT8672
ON OFF
EN/UVLO
GND
8672 TA01a
Rectification of Input Ripple
V
OUT
5A
470µF
V
OUT
2V/DIV
V
BATT
2V/DIV
IPD100N06S4-03
TO SYSTEM LOADS
1 F
100 H
4.7µF
+
AUXSW
PG
500µs/DIV
8672 TA01b
For more information
www.linear.com/LT8672
1
8672f
LT8672
ABSOLUTE MAXIMUM RATINGS
(Notes 1 and 2)
PIN CONFIGURATION
TOP VIEW
EN/UVLO
GND
PG
GND
NC
1
2
3
4
5
10
9
8
7
6
GATE
SOURCE
DRAIN
AUX
AUXSW
DRAIN ...................................................... –0.3V to 42V
SOURCE, EN/UVLO ................................... –40V to 42V
DRAIN–SOURCE ......................................... –5V to 54V
AUX .......................................................... V
DRAIN
+ 13V
GATE .........................V
SOURCE
– 0.3V to V
SOURCE
+ 17V
GATE ................................... V
AUX
– 67V to V
AUX
+ 0.3V
PG .............................................................. –0.3V to 5V
Operating Junction Temperature Range (Notes 3, 4)
E-, I-Grades ..................................... −40°C to 125°C
H-Grades ......................................... −40°C to 150°C
Storage Temperature Range ................ −65°C to 150°C
Lead Temperature (Soldering, 10 sec)
MS Package .................................................... 300°C
MS PACKAGE
10-LEAD PLASTIC MSOP
T
JMAX
= 150°C,
θ
JA
= 160°C/W
ORDER INFORMATION
LEAD FREE FINISH
LT8672EMS#PBF
LT8672IMS#PBF
LT8672HMS#PBF
TAPE AND REEL
LT8672EMS#TRPBF
LT8672IMS#TRPBF
LT8672HMS#TRPBF
http://www.linear.com/product/LT8672#orderinfo
PART MARKING*
LTGYT
LTGYT
LTGYT
PACKAGE DESCRIPTION
10-Lead Plastic MSOP
10-Lead Plastic MSOP
10-Lead Plastic MSOP
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/.
Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
2
8672f
For more information
www.linear.com/LT8672
LT8672
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
SOURCE
= V
DRAIN
= 12V, unless otherwise noted. (Note 3)
PARAMETER
Minimum Drain Voltage
Total System Quiescent Current
V
EN/UVLO
= 0V
l
ELECTRICAL CHARACTERISTICS
CONDITIONS
l
MIN
TYP
2.85
3.5
20
20
MAX
3
5
15
26
39
1.34
1.26
0.1
0.1
UNITS
V
µA
µA
µA
µA
V
V
mV
µA
µA
Ω
V
mA
Ω
V
V
EN/UVLO
= 2V, Active Rectifier Controller
In Regulation (Note 4)
EN/UVLO Pin Threshold High
EN/UVLO Pin Threshold Low
EN/UVLO Pin Hysteresis
EN/UVLO Pin Current
PG Pin Leakage
PG Pull-Down Resistance
Auxiliary Boost Regulator
Regulation Voltage V
AUX
– V
DRAIN
Power NMOS Current Limit
Power NMOS On-Resistance
Catch Diode Forward Voltage
AUXSW Pin Leakage
Active Rectifier Controller
SOURCE–DRAIN Regulation Voltage
SOURCE–DRAIN Fast Pull-Up Threshold
DRAIN Current
SOURCE Current
Maximum Gate Drive (GATE–SOURCE)
Gate Pull-Up Current
Gate Pull-Down Current
Gate-Source Off Voltage for Reverse SOURCE
Gate Turn-Off Delay Time
Gate Turn-On Delay Time
Maximum Frequency of AC Input Signal to Be
Rectified
Fault Condition, V
SOURCE
= –5V, I
GATE
= 1mA
Fault Condition, V
SOURCE
= –40V, I
GATE
= 1mA
Step (V
SOURCE
–V
DRAIN
) from –70mV to 130mV
V
GATE
–V
SOURCE
< 1V, C
GATE–SOURCE
= 10nF
Step (V
SOURCE
–V
DRAIN
) from 130mV to −70mV
V
GATE
–V
SOURCE
> 5V , C
GATE–SOURCE
= 10nF
AC Input Ripple < 6V
P-P
, C
GATE–SOURCE
= 10nF
AC Input Ripple < 2V
P-P
, C
GATE–SOURCE
= 10nF
With Gate Driver in Regulation
With Gate Driver in Regulation
Fault Condition, V
SOURCE
= –40V
I
DIODE
= 100mA
V
AUXSW
= 12V
V
EN/UVLO
= 2V
V
PG
= 3.3V
V
PG
= 0.1V
Pin Voltage Rising
Pin Voltage Falling
l
l
l
1.22
1.16
–0.1
–0.1
1.28
1.21
70
l
650
10.2
75
11
100
2
0.8
–0.2
2000
11.8
120
l
l
0.2
20
75
12
5
–1
11.8
25
90
µA
mV
mV
µA
µA
mA
V
mA
mA
l
l
10
60
l
10.2
–26
170
11
–50
300
0.01
0.01
0.6
1.7
l
l
l
l
l
l
0.3
0.3
1.1
3.1
V
V
µs
µs
kHz
kHz
50
100
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect the device
reliability and lifetime.
Note 2:
Positive currents flow into pins, negative currents flow out of pins.
Minimum and Maximum values refer to absolute values.
Note 3:
The LT8672E is guaranteed to meet performance specifications
from 0°C to 125°C junction temperature. Specifications over the −40°C
to 125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LT8672I is guaranteed over the full −40°C to 125°C operating junction
temperature range. The LT8672H is guaranteed over the full −40°C to
150°C operating junction temperature range.
Note 4:
Total system current with active rectifier controller in regulation.
Whether a motherboard is good or not, players have the most say, but why a motherboard can be so good, we have to look at some more in-depth things. Today, the editor of HR Connector Technology will t...
error:Unknown error. Win32 error code:126 It tells me that there is a problem with the path, but how do I set the path? My download directory is already set to \. Where else should I change it? Please...
Starbucks has launched a wireless charging coffee table. You can charge your phone by connecting it to a charging ring and placing it on a specific coffee table induction area. The trial has already b...
By chance, I was wandering around the electronics market and received an HP54645D oscilloscope with logic analyzer function. It was considered a magical device back then, and it was the pinnacle of HP...
Course link: Become an FPGA Designer in 4 Hours (ODSWBECOME) [url=http://www.altera.com.cn/education/training/courses/ODSWBECOME]http://www.altera.com.cn/education/training/courses/ODSWBECOME[/url] [c...
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
In recent years, the market for mobile/portable devices such as smartphones and laptops has continued to grow rapidly. While these products continue to integrate more new features to enhance the ...[Details]
1. Introduction
Light control circuit plays a vital role in urban street lamps or corridor lighting. With light control circuit, the lights can be automatically turned on and off according to ...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
Liquid crystal display (LCD) panels have a wide range of applications, from small portable electronic devices to large fixed devices, including digital cameras, laptops, personal data assistants, d...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
1. Proposal of
reconfigurable
measurement and control system
The measurement and control system generally refers to a system based on
computers
to realize data acquisition a...[Details]
The DisplayPort interface standard is approved by the Video Electronics Standards Association (VESA) to provide an open, scalable standard for the entire industry. The development of DisplayPort ca...[Details]
Integrated technical exchanges
京公网安备 11010802033920号
EEWORLD
