8 SO ............................................................. -40°C to +105°C
14 SO ........................................................... -40°C to +125°C
TSSOP.......................................................... -40°C to +125°C
Junction Temperature ......................................................+150°C
Storage Temperature Range ............................ -65°C to +150°C
Lead Temperature (soldering, 10s) ................................. +300°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Package Thermal Characteristics
(Note 1)
Junction-to-Case Thermal Resistance (θ
JC
)
Junction-to-Ambient Thermal Resistance (θ
JA
)
8 SO ............................................................................38°C/W
8 SO ..........................................................................132°C/W
14 SO ..........................................................................34°C/W
14 SO ..........................................................................84°C/W
I have used it and it works. According to a forum, it should be installed in the INF of C: so I did that. I haven't verified whether it can be installed elsewhere. Haha. Share it with everyone! [[i] T...
Hey guys, I have a question about ADS. I want to run ARM 2440 naked, but when I use AXD debugging, it reports DBE Warning 00056: The statement into which was stepped is singular (ie it has no exit). T...
1: Basic variables in Verilog are wire net type and register type. Wire net type variables are synthesized into wire, while registers may be synthesized into WIRE, latch and flip-flop. 2: Mapping of V...
1. Principle 1. Infrared emission protocol There are many infrared communication protocols. This experiment uses the NEC protocol. This protocol uses PWM modulation and uses pulse width to represen...[Details]
Today, under the guidance of a low-level expert, I learned how to configure the PWM module! Woof! First open the file configured last time, as follows: Then, we need to use TIM1 to set PWM: Then,...[Details]
I used STM32CubeMX V4.22.1 to generate a project including EHT and Lwip. The debugging has been abnormal. After careful inspection, the following problems were found: 1. The hardware uses LAN8720A, b...[Details]
Overview
Lightning is a strong discharge phenomenon that occurs between thunderstorm clouds and between thunderstorm clouds and the earth due to severe convective weather. Lightning is gen...[Details]
There has been a lot of news about Huawei
phones
recently
. At the
Huawei
Global Analyst Conference
on the 17th
,
Huawei
announced that it will launch
5G
phones
in the seco...[Details]
The photovoltaic inverter is the core equipment of the photovoltaic system. Its main function is to convert the direct current generated by the photovoltaic modules into alternating current that meets...[Details]
Superconductors have physical properties such as zero resistance effect, Meissner effect and Josephson effect, which make them have broad application prospects and unparalleled advantages in many b...[Details]
In the project, CPLD is needed to complete part of the algorithm design. The parameters are given by AVR, so the communication between AVR and CPLD needs to be completed. Therefore, a test program is...[Details]
Why does MCU have a watchdog? With this question, let's learn about watchdogs. Even the 51 single-chip microcomputer has a watchdog, which shows that this dog has a special meaning to us. The purpose...[Details]
LiDAR: Autonomous driving from the perspective of optoelectronic technology LiDAR and competing sensor technologies (camera, radar, and ultrasonic) intensify the need for sensor fusion and the need...[Details]
Introduction: As a power electronic device, the photovoltaic inverter mainly converts the direct current generated by the photovoltaic module into alternating current. Because there are thousands o...[Details]
ADI has established long-term good relationships with car manufacturers and Tier 1 component suppliers. Based on its previous long-term successful cooperation with new energy vehicles and suppliers a...[Details]
The clock system of STM32 can be directly summarized in a diagram (from the STM32F10X reference manual). The following is an analysis of this diagram 1. STM32 input clock source 1.1 Function of cl...[Details]
Summary of STM32 peripheral DMA usage: 1. Select DAM mode according to your needs: (1) Circular mode—DMA_Mode = DMA_Mode_Circular (2) Normal mode—DMA_Mode = DMA_Mode_Normal 2. For Chanel3 of DMA1, t...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
