3 Terminals Low ESL Chip Multilayer Ceramic Capacitors (EMIFIL) for General Purpose
NFM18CC223R1C3_ (0603, 22000pF, DC16V)
_: packaging code
1.Scope
Reference Sheet
This product specification is applied to 3 Terminals Low ESL Chip Multilayer Ceramic Capacitorss (EMIFIL) used for General Electronic equipment.
2.MURATA Part NO. System
(Ex.)
NFM
18
(1)L/W
Dimensions
CC
(2)Features
223
(3)Nominal
Capacitance
R
1C
3
(6)Electrode
D
(7)Packaging Code
(4)Characteristics
(5)DC Rated Voltage
3. Type & Dimensions
a)Equivalent Circuit
(1)-1 L
i
1.6±0.1
0.4±0.1
(1)-2 W
j
0.8±0.1
0.2±0.1
T
0.6±0.1
e
0.25±0.1
(Unit:mm)
g
0.2 min.
4.Rated value
(3) Nominal Capacitance
Capacitance Tolerance
(5)
DC Rated
Voltage
Rated
Current
(mA)
DC
Resistance
Insulation
Resistance
Specifications and Test Methods
(Operating /Storage Temp. Range)
22000 pF
±20 %
DC 16 V
1A(DC)
50mΩmax. 1000MΩmin.
-55 to 125 °C / -55 to 125 °C
5.Package
mark
D
(7) Packaging
f180mm
Reel
PAPER W8P4
Packaging Unit
4000 pcs./Reel
Product specifications in this catalog are as of Dec.7,2017,and are subject to change or obsolescence without notice.
Please consult the approval sheet before ordering.
Please read rating and !Cautions first.
NFM18CC223R1C3-01
1
■SPECIFICATIONS
AND TEST METHODS
Electrical Performance
Item
No
1 Capacitance
(Cap.)
Specification
Shown in Rated value.
Test Method
Frequency
22 to 47pF : 1±0.1MHz
100 to 22000pF : 1±0.1kHz
Voltage : 1±0.2V(rms)
Voltage : Rated Voltage
Time : 2 minutes max.
Measured with 100mA max.
Products shall not be damaged.
Test Voltage : Rated Voltage x 300%
Time : 1 to 5 s
Charge Current : 50mA max.
Includes self-heating
2 Insulation
Resistance(I.R.)
3 DC Resistance
4 Withstanding Voltage
5 Operating Temperature Shown in Rated value.
6 Storage Temperature
Standard Testing Condition
< Unless otherwise specified >
Temperature : Ordinary Temp. / 15 °C to 35 °C
Humidity: Ordinary Humidity / 25 %(RH) to 85 %(RH)
< In case of doubt >
Temperature: 20 °C ± 2 °C
Humidity: 60 %(RH) to 70 %(RH)
Atmospheric pressure: 86 kPa to 106 kPa
JEMCPS-02209D
2
■SPECIFICATIONS
AND TEST METHODS
Mechanical Performance
Item
No
1 Appearance and
Dimensions
2 Solderability
Specification
Appearance:No defects or abnormalities.
Dimensions:Within the specified dimensions.
Electrodes shall be at least 90% covered with
new solder coating.
Test Method
Appearance:Visual inspection.
Dimensions:Using Measuring instrument of dimension.
Flux : Solution of rosin ethanol 25(mass)%
Pre-heat : 150±10°C, 60 to 90s
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 240±3°C
Immersion Time : 3±1s
Immersion and emersion rates : 25mm/s
Flux : Solution of rosin ethanol 25(mass)%
Pre-heat : 150±10°C, 60 to 90s
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 270±5°C
Immersion Time : 10±1s
Immersion and emersion rates : 25mm/s
Initial values : About 100 to 22000pF,
measured after heat treatment (150+0/-10 °C,1hour) and
exposure in the room condition for 48±4 hours.
Then measured after exposure in the room condition for
following hours.
22 to 47pF : 24±2 hours
100 to 22000pF : 48±4 hours
It shall be soldered on the glass-epoxy substrate(t=1.0mm).
Deflection : 2mm
Keeping Time : 30s
Pressure jig
R340
3 Resistance to
soldering heat
Meet Table 1.
Table 1
Appearance
Cap. Change
I.R.
22 to 2200pF
Rdc
22000pF
No damaged
Within ±7.5%
Meet the initial rated value.
0.5
max.
0.05
max.
4 Bending Strength
Meet Table 2.
Table 2
Appearance
Cap. Change
22 to 2200pF
Rdc
22000pF
No damaged
Within ±7.5%
0.5
max.
0.05
max.
F
Deflection
45
45
Product
(in mm)
5 Drop
Products shall be no failure after tested.
It shall be dropped on concrete or steel board.
Method : Free fall
Height : 1m
Attitude from which the product is dropped : 3 directions
The Number of Time : 3 times for each direction
(Total 9 times)
It shall be soldered on the glass-epoxy substrate.
Applying Force (F) : 9.8N
Applying Time : 30s
0.5
6 Bonding Strength
The electrodes shall be no failure after tested.
0.6
(in mm)
0.4
1.6
7 Vibration
Meet Table 3.
Table 3
Appearance
Capacitance
22 to 2200pF
Rdc
22000pF
No damaged
Meet the initial rated value.
0.5
max.
0.05
max.
It shall be soldered on the glass-epoxy substrate.
Oscillation Frequency : 10 to 2000 to 10Hz for 20 minutes.
Total amplitude 1.5 mm or Acceleration amplitude 196m/s2
whichever is smaller.
Time : A period of 2 hours in each of 3 mutually
perpendicular directions. (Total 6 hours)
Initial values : About 100 to 22000pF,
measured after heat treatment (150+0/-10 °C,1hour)
and exposure in the room condition for 48±4 hours.
Then measured after exposure in the room condition for
following hours.
22
to 47pF
: 24±2 hours
100
to 22000pF : 48±4 hours
JEMCPS-02209D
3
■SPECIFICATIONS
AND TEST METHODS
Environment Performance
It shall be soldered on the glass-epoxy substrate.
Item
No
Specification
1 Temperature Cycling Meet Table 1.
Test Method
1 Cycle
1 step : -55+0/-3℃ / 30+3/-0 min
2 step : Room Temperature / within 3 min
3 step : +125+3/-0℃ / 30+3/-0 min
4 step : Room Temperature / within 3 min
Total of 10 cycles
Initial values : About 100 to 22000pF, measured after heat
treatment(150+0/-10°C,1hour) and exposure in the room
condition for 48±4 hours.
Then measured after exposure in the room condition for
following hours.
22
to 47pF
: 24±2 hours
100
to 22000pF : 48±4 hours
About 100 to 22000pF, If it’s doubt, measured after heat
treatment (150+0/-10 °C,1hour) and exposure in the room
condition for 48±4 hours.
Temperature : 40±2°C
Humidity : 90 to 95%(RH)
Time : 500+24/-0 hours
Initial values : About 100 to 22000pF,measured after heat
treatment (150+0/-10 °C,1hour), and exposure in the room
condition for 48±4 hours.
Then measured after exposure in the room condition for
following hours.
22
to 47pF
: 24±2 hours
100
to 22000pF : 48±4 hours
About 100~22000pF, If it’s doubt, measured after heat
treatment (150+0/-10 °C,1hour) and exposure in the room
condition for 48±4 hours.
Temperature : 125±2°C
Test Voltage : Rated Voltage x 200%
Charge Current : 50mA max.
Time : 1000+48/-0 hours
Initial values : About 100 to 22000pF,measured after voltage
treatment (Maximum Operating Temperature±2°C, Rated
Voltage x 200%, 1hour) and exposure in the room condition
for 48±4 hours.
Then measured after exposure in the room condition for
following hours.
22 to 47pF
: 24±2 hours
100
to 22000pF : 48±4 hours
Temperature : -55±2°C
Time : 500+24/-0 hours
Initial values : About 100 to 22000pF,measured after heat
treatment (150+0/-10 °C,1hour), and exposure in the room
condition for 48±4 hours.
Then measured after exposure in the room condition for
following hours.
22
to 47pF : 24±2 hours
100
to 22000pF : 48±4 hours
About 100 to 22000pF, If it’s doubt, measured after heat
treatment (150+0/-10 °C,1hour) and exposure in the room
condition for 48±4 hours.
2 Humidity
Meet Table 4.
Table 4
Appearance
Cap. Change
I.R.
22 to 2200pF
Rdc
22000pF
No damaged
Within ±12.5%
Meet the initial rated value.
0.5
max.
0.05
max.
Appearance
Cap. Change
I.R.
Rdc
1,2
3 Heat Life
4 Cold Resistance
JEMCPS-02209D
4
PACKAGING
NFM18 Type
f
1.5±
0.1
0
Sporocket Hole
4.0±0.1
1.75±0.1
1. Appearance and Dimensions (8mm-wide paper tape)
3.5±0.05
1.85±0.1
8.0±0.3
Chip thickness
(T)
0.8
0.6
Dimension
(a)
1.1max
0.9max
(in mm)
1.05±0.1
4.0±0.1
2.0±0.05
0.9max.
2. Specification of Taping
Direction of feed
(1) Packing quantity (standard quantity)
4000 pcs. / reel
(2) Packing Method
Products shall be packaged in the cavity of the base tape and sealed by top tape and bottom tape.
(3) Sprocket Hole
The sprocket holes are to the right as the tape is pulled toward the user.
(4) Base tape and Top tape
The base tape and top tape have no spliced point.
(5) Cavity
There shall not be burr in the cavity.
(6) Missing components number
Missing components number within 0.1% of the number per reel or 1 pc., whichever is greater,and are not continuous.
The specified quantity per reel is kept.
3. Pull Strength of Top Tape
5Nmin.(※Only for NFM18PS, 8Nmin.)
4. Peeling off force of top tape
0.1N to 0.6N (minimum value is typical)
165
Speed of Peeling off : 300 mm / min
a
to 180 degree
Top tape
F
Bottom tape
Base tape
5. Dimensions of Leader-tape, Trailer and Reel
There shall be leader-tape (top tape and empty tape) and trailer-tape (empty tape) as follows.
Trailer
2.0±0.5
160 min.
Leader
Label
190 min.
Empty tape
f
13.0±0.2
210 min.
Top tape
f
60±
0
f
21.0±0.8
1
9±
1
0
13±1.4
f
180±
3
0
Direction of feed
(in mm)
JEMCPP-02231A
5
京公网安备 11010802033920号
EEWORLD
