ATMEGA16-8AC datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Microcontrollers and processors> ATMEGA16-8AC

ATMEGA16-8AC: DescriptionRISC Microcontroller, 8-Bit, FLASH, 8MHz, CMOS, PQFP44, 10 X 10 MM, 1 MM HEIGHT, 0.80 MM PITCH, PLASTIC, MS-026ACB, TQFP-44; CategoryMicrocontrollers and processors; File Size344KB，14 Pages; ManufacturerAtmel (Microchip)

Download Datasheet Parametric Compare View All

ATMEGA16-8AC Overview

RISC Microcontroller, 8-Bit, FLASH, 8MHz, CMOS, PQFP44, 10 X 10 MM, 1 MM HEIGHT, 0.80 MM PITCH, PLASTIC, MS-026ACB, TQFP-44

ATMEGA16-8AC Parametric

Parameter Name	Attribute value
Is it lead-free?	Contains lead
Is it Rohs certified?	incompatible
Maker	Atmel (Microchip)
Parts packaging code	QFP
package instruction	TQFP,
Contacts	44
Reach Compliance Code	not_compliant
core architecture	AVR
Device core	AVR
clock speed	16
Memory	1
flash memory	16
were able	0
Adc channel	8
ADC resolution	10
Is Samacsys	N
Has ADC	YES
Address bus width
bit size	8
maximum clock frequency	8 MHz
DAC channel	NO
DMA channel	NO
External data bus width
JESD-30 code	S-PQFP-G44
JESD-609 code	e0
length	10 mm
Humidity sensitivity level	3
Number of I/O lines	32
Number of terminals	44
On-chip program ROM width	16
Maximum operating temperature	70 °C
Minimum operating temperature
PWM channel	YES
Package body material	PLASTIC/EPOXY
encapsulated code	TQFP
Package shape	SQUARE
Package form	FLATPACK, THIN PROFILE
Peak Reflow Temperature (Celsius)	240
Certification status	Not Qualified
RAM (bytes)	1024
rom(word)	8192
ROM programmability	FLASH
Maximum seat height	1.2 mm
speed	8 MHz
Maximum supply voltage	5.5 V
Minimum supply voltage	2.7 V
surface mount	YES
technology	CMOS
Temperature level	COMMERCIAL
Terminal surface	Tin/Lead (Sn/Pb)
Terminal form	GULL WING
Terminal pitch	0.8 mm
Terminal location	QUAD
Maximum time at peak reflow temperature	30
width	10 mm
uPs/uCs/peripheral integrated circuit type	MICROCONTROLLER, RISC
Base Number Matches	1

Preview

Download Datasheet

View All

Features

•

High-performance, Low-power AVR

8-bit Microcontroller

•

Advanced RISC Architecture

– 130 Powerful Instructions – Most Single-clock Cycle Execution

– 32 x 8 General Purpose Working Registers

– Fully Static Operation

– Up to 16 MIPS Throughput at 16 MHz

– On-chip 2-cycle Multiplier

Nonvolatile Program and Data Memories

– 16K Bytes of In-System Self-Programmable Flash

Endurance: 1,000 Write/Erase Cycles

– Optional Boot Code Section with Independent Lock Bits

In-System Programming by On-chip Boot Program

True Read-While-Write Operation

– 512 Bytes EEPROM

Endurance: 100,000 Write/Erase Cycles

– 1K Byte Internal SRAM

– Programming Lock for Software Security

JTAG (IEEE std. 1149.1 Compliant) Interface

– Boundary-scan Capabilities According to the JTAG Standard

– Extensive On-chip Debug Support

– Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface

Peripheral Features

– Two 8-bit Timer/Counters with Separate Prescalers and Compare Modes

– One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture

Mode

– Real Time Counter with Separate Oscillator

– Four PWM Channels

– 8-channel, 10-bit ADC

8 Single-ended Channels

7 Differential Channels (TQFP Package Only)

2 Differential Channels with Programmable Gain (1x, 10x, 200x) (TQFP Package

Only)

– Byte-oriented 2-wire Serial Interface

– Programmable Serial USART

– Master/Slave SPI Serial Interface

– Programmable Watchdog Timer with Separate On-chip Oscillator

– On-chip Analog Comparator

Special Microcontroller Features

– Power-on Reset and Programmable Brown-out Detection

– Internal Calibrated RC Oscillator

– External and Internal Interrupt Sources

– Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby

and Extended Standby

I/O and Packages

– 32 Programmable I/O Lines

– 40-pin PDIP and 44-lead TQFP

Operating Voltages

– 2.7 - 5.5V (ATmega16L)

– 4.5 - 5.5V (ATmega16)

Speed Grades

– 0 - 8 MHz (ATmega16L)

– 0 - 16 MHz (ATmega16)

•

8-bit

Microcontroller

with 16K Bytes

In-System

Programmable

Flash

ATmega16

ATmega16L

Preliminary

Summary

•

Rev. 2466AS–08/01

Note: This is a summary document. A complete document is

available on our web site at

www.atmel.com.

The AVR core combines a rich instruction set with 32 general purpose working registers.

All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing

two independent registers to be accessed in one single instruction executed in one clock

cycle. The resulting architecture is more code efficient while achieving throughputs up to

ten times faster than conventional CISC microcontrollers.

The ATmega16 provides the following features: 16K bytes of In-System Programmable

Flash with Read-While-Write capabilities, 512 bytes EEPROM, 1K byte SRAM, 32 gen-

eral-purpose I/O lines, 32 general purpose working registers, a JTAG interface for

Boundary-scan, On-chip Debugging support and programming, three flexible

timer/counters with compare modes, internal and external interrupts, a serial program-

mable USART, a byte oriented 2-wire Serial Interface, an 8-channel, 10-bit ADC with

optional differential input stage with programmable gain (TQFP package only), a pro-

grammable Watchdog Timer with internal oscillator, an SPI serial port, and six software

selectable power saving modes. The Idle mode stops the CPU while allowing the

SRAM, timer/counters, SPI port, and interrupt system to continue functioning. The

Power-down mode saves the register contents but freezes the oscillator, disabling all

other chip functions until the next interrupt or hardware reset. In Power-save mode, the

asynchronous timer continues to run, allowing the user to maintain a timer base while

the rest of the device is sleeping. The ADC Noise Reduction Mode stops the CPU and

all I/O modules except asynchronous timer and ADC, to minimize switching noise during

ADC conversions. In Standby mode, the crystal/resonator oscillator is running while the

rest of the device is sleeping. This allows very fast start-up combined with low-power

consumption. In Extended Standby mode, both the main oscillator and the asynchro-

nous timer continue to run.

The device is manufactured using Atmel’s high density nonvolatile memory technology.

The On-chip ISP Flash allows the program memory to be reprogrammed in-system

through an SPI serial interface, by a conventional nonvolatile memory programmer, or

by an On-chip Boot program running on the AVR core. The boot program can use any

interface to download the application program in the Application Flash memory. Soft-

ware in the Boot Flash section will continue to run while the Application Flash section is

updated, providing true Read-While-Write operation. By combining an 8-bit RISC CPU

with In-System Self-Programmable Flash on a monolithic chip, the Atmel ATmega16 is

a powerful microcontroller that provides a highly-flexible and cost-effective solution to

many embedded control applications.

The ATmega16 AVR is supported with a full suite of program and system development

tools including: C compilers, macro assemblers, program debugger/simulators, in-circuit

emulators, and evaluation kits.

Pin Descriptions

VCC

GND

Port A (PA7..PA0)

Digital supply voltage.

Ground.

Port A serves as the analog inputs to the A/D Converter.

Port A also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used.

Port pins can provide internal pull-up resistors (selected for each bit). The Port A output

buffers have symmetrical drive characteristics with both high sink and source capability.

When pins PA0 to PA7 are used as inputs and are externally pulled low, they will source

current if the internal pull-up resistors are activated. The Port A pins are tristated when a

reset condition becomes active, even if the clock is not running.

ATmega16(L)

2466AS–08/01

ATmega16(L)

Port B (PB7..PB0)

Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each

bit). The Port B output buffers have symmetrical drive characteristics with both high sink

and source capability. As inputs, Port B pins that are externally pulled low will source

current if the pull-up resistors are activated. The Port B pins are tristated when a reset

condition becomes active, even if the clock is not running.

Port B also serves the functions of various special features of the ATmega16 as listed

on page 55.

Port C (PC7..PC0)

Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each

bit). The Port C output buffers have symmetrical drive characteristics with both high sink

and source capability. As inputs, Port C pins that are externally pulled low will source

current if the pull-up resistors are activated. The Port C pins are tristated when a reset

condition becomes active, even if the clock is not running. If the JTAG interface is

enabled, the pull-up resistors on pins PC5(TDI), PC3(TMS) and PC2(TCK) will be acti-

vated even if a reset occurs.

Port C also serves the functions of the JTAG interface and other special features of the

ATmega16 as listed on page 58.

Port D (PD7..PD0)

Port D is an 8-bit bidirectional I/O port with internal pull-up resistors (selected for each

bit). The Port D output buffers have symmetrical drive characteristics with both high sink

and source capability. As inputs, Port D pins that are externally pulled low will source

current if the pull-up resistors are activated. The Port D pins are tristated when a reset

condition becomes active, even if the clock is not running.

Port D also serves the functions of various special features of the ATmega16 as listed

on page 60.

RESET

Reset input. A low level on this pin for longer than the minimum pulse length will gener-

ate a reset, even if the clock is not running. The minimum pulse length is given in Table

15 on page 35. Shorter pulses are not guaranteed to generate a reset.

Input to the inverting oscillator amplifier and input to the internal clock operating circuit.

Output from the inverting oscillator amplifier.

This is the supply voltage pin for Port A and the A/D Converter. It should be externally

connected to VCC, even if the ADC is not used. If the ADC is used, it should be con-

nected to VCC through a low-pass filter.

This is the analog reference pin for the A/D Converter.

XTAL1

XTAL2

AVCC

AREF

2466AS–08/01

ATMEGA16-8AC Related Products

	ATMEGA16-8AC	ATMEGA16-8PL	ATMEGA16-8PI	ATMEGA16-8AU	ATMEGA16-8AL	ATMEGA16-8AI	ATMEGA16-8PU	ATMEGA16-8PC
Description	RISC Microcontroller, 8-Bit, FLASH, 8MHz, CMOS, PQFP44, 10 X 10 MM, 1 MM HEIGHT, 0.80 MM PITCH, PLASTIC, MS-026ACB, TQFP-44	RISC Microcontroller, 8-Bit, FLASH, 8MHz, CMOS, PDIP40, 0.600 INCH, PLASTIC, DIP-40	RISC Microcontroller, 8-Bit, FLASH, 8MHz, CMOS, PDIP40, 0.600 INCH, PLASTIC, DIP-40	RISC Microcontroller, 8-Bit, FLASH, 8MHz, CMOS, PQFP44, 10 X 10 MM, 1 MM HEIGHT, 0.80 MM PITCH, PLASTIC, MS-026ACB, TQFP-44	RISC Microcontroller, 8-Bit, FLASH, 8MHz, CMOS, PQFP44, 10 X 10 MM, 1 MM HEIGHT, 0.80 MM PITCH, PLASTIC, MS-026ACB, TQFP-44	RISC Microcontroller, 8-Bit, FLASH, 8MHz, CMOS, PQFP44, 10 X 10 MM, 1 MM HEIGHT, 0.80 MM PITCH, PLASTIC, MS-026ACB, TQFP-44	RISC Microcontroller, 8-Bit, FLASH, 8MHz, CMOS, PDIP40, 0.600 INCH, PLASTIC, DIP-40	RISC Microcontroller, 8-Bit, FLASH, 8MHz, CMOS, PDIP40, 0.600 INCH, PLASTIC, DIP-40
Is it lead-free?	Contains lead	Lead free	Contains lead	Lead free	Lead free	Contains lead	Lead free	Contains lead
Is it Rohs certified?	incompatible	conform to	incompatible	conform to	conform to	incompatible	conform to	incompatible
Parts packaging code	QFP	DIP	DIP	QFP	QFP	QFP	DIP	DIP
package instruction	TQFP,	DIP,	DIP,	TQFP,	TQFP,	10 X 10 MM, 1 MM HEIGHT, 0.80 MM PITCH, PLASTIC, MS-026ACB, TQFP-44	DIP,	DIP,
Contacts	44	40	40	44	44	44	40	40
Reach Compliance Code	not_compliant	compliant	not_compliant	compliant	compliant	not_compliant	compliant	not_compliant
core architecture	AVR	AVR	AVR	AVR	AVR	AVR	AVR	AVR
Device core	AVR	AVR	AVR	AVR	AVR	AVR	AVR	AVR
clock speed	16	16	16	16	16	16	16	16
Memory	1	1	1	1	1	1	1	1
flash memory	16	16	16	16	16	16	16	16
Adc channel	8	8	8	8	8	8	8	8
ADC resolution	10	10	10	10	10	10	10	10
Has ADC	YES	YES	YES	YES	YES	YES	YES	YES
bit size	8	8	8	8	8	8	8	8
maximum clock frequency	8 MHz	8 MHz	8 MHz	8 MHz	8 MHz	8 MHz	8 MHz	8 MHz
DAC channel	NO	NO	NO	NO	NO	NO	NO	NO
DMA channel	NO	NO	NO	NO	NO	NO	NO	NO
JESD-30 code	S-PQFP-G44	R-PDIP-T40	R-PDIP-T40	S-PQFP-G44	S-PQFP-G44	S-PQFP-G44	R-PDIP-T40	R-PDIP-T40
JESD-609 code	e0	e3	e0	e3	e3	e0	e3	e0
length	10 mm	52.325 mm	52.325 mm	10 mm	10 mm	10 mm	52.325 mm	52.325 mm
Humidity sensitivity level	3	1	1	3	3	3	1	1
Number of I/O lines	32	32	32	32	32	32	32	32
Number of terminals	44	40	40	44	44	44	40	40
On-chip program ROM width	16	16	16	16	16	16	16	16
Maximum operating temperature	70 °C	70 °C	85 °C	85 °C	70 °C	85 °C	85 °C	70 °C
PWM channel	YES	YES	YES	YES	YES	YES	YES	YES
Package body material	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY
encapsulated code	TQFP	DIP	DIP	TQFP	TQFP	TQFP	DIP	DIP
Package shape	SQUARE	RECTANGULAR	RECTANGULAR	SQUARE	SQUARE	SQUARE	RECTANGULAR	RECTANGULAR
Package form	FLATPACK, THIN PROFILE	IN-LINE	IN-LINE	FLATPACK, THIN PROFILE	FLATPACK, THIN PROFILE	FLATPACK, THIN PROFILE	IN-LINE	IN-LINE
Peak Reflow Temperature (Celsius)	240	260	225	260	260	240	245	225
Certification status	Not Qualified	Not Qualified	Not Qualified	Not Qualified	Not Qualified	Not Qualified	Not Qualified	Not Qualified
RAM (bytes)	1024	1024	1024	1024	1024	1024	1024	1024
rom(word)	8192	8192	8192	8192	8192	8192	8192	8192
ROM programmability	FLASH	FLASH	FLASH	FLASH	FLASH	FLASH	FLASH	FLASH
Maximum seat height	1.2 mm	4.83 mm	4.83 mm	1.2 mm	1.2 mm	1.2 mm	4.83 mm	4.83 mm
speed	8 MHz	8 MHz	8 MHz	8 MHz	8 MHz	8 MHz	8 MHz	8 MHz
Maximum supply voltage	5.5 V	5.5 V	5.5 V	5.5 V	5.5 V	5.5 V	5.5 V	5.5 V
Minimum supply voltage	2.7 V	2.7 V	2.7 V	2.7 V	2.7 V	2.7 V	2.7 V	2.7 V
surface mount	YES	NO	NO	YES	YES	YES	NO	NO
technology	CMOS	CMOS	CMOS	CMOS	CMOS	CMOS	CMOS	CMOS
Temperature level	COMMERCIAL	COMMERCIAL	INDUSTRIAL	INDUSTRIAL	COMMERCIAL	INDUSTRIAL	INDUSTRIAL	COMMERCIAL
Terminal surface	Tin/Lead (Sn/Pb)	MATTE TIN	Tin/Lead (Sn/Pb)	Matte Tin (Sn)	Matte Tin (Sn)	Tin/Lead (Sn/Pb)	Matte Tin (Sn)	Tin/Lead (Sn/Pb)
Terminal form	GULL WING	THROUGH-HOLE	THROUGH-HOLE	GULL WING	GULL WING	GULL WING	THROUGH-HOLE	THROUGH-HOLE
Terminal pitch	0.8 mm	2.54 mm	2.54 mm	0.8 mm	0.8 mm	0.8 mm	2.54 mm	2.54 mm
Terminal location	QUAD	DUAL	DUAL	QUAD	QUAD	QUAD	DUAL	DUAL
Maximum time at peak reflow temperature	30	30	30	40	40	30	NOT SPECIFIED	30
width	10 mm	15.24 mm	15.24 mm	10 mm	10 mm	10 mm	15.24 mm	15.24 mm
uPs/uCs/peripheral integrated circuit type	MICROCONTROLLER, RISC	MICROCONTROLLER, RISC	MICROCONTROLLER, RISC	MICROCONTROLLER, RISC	MICROCONTROLLER, RISC	MICROCONTROLLER, RISC	MICROCONTROLLER, RISC	MICROCONTROLLER, RISC
Maker	Atmel (Microchip)	-	Atmel (Microchip)	Atmel (Microchip)	Atmel (Microchip)	Atmel (Microchip)	Atmel (Microchip)	Atmel (Microchip)

Recommended Resources

Design of infrared communication circuit based on single chip microcomputer

Safe and reliable delay switch circuit

STK436 power amplifier circuit

555 brightness display circuit

Emitter follower and inverter combined application circuit

MAXl898 single-cell Li+ battery linear charger

Show off the USB flash drive prizes for community activities: [font="][size=16px][b] I received a USB flash drive as a prize from TE's EDM series promotion activities. I would like to express my gratitude to the community and TE! Here are some of the prizes I re...; windworld Talking

The circuit is quite classic. Can anyone explain it to me?: It feels a bit difficult to learn analog electronics. Which expert can help me analyze this circuit? For example, the lm393 at the back (Figure 1) should be a square wave generator. After welding the ...; 110107110 Analog electronics

[Help Post] ADS1115 reads differential pressure transmitter data, and zero point drift and zero point attenuation are found after mean filtering: ADS1115 reads the data of the differential pressure transmitter. After mean filtering, it is found that the zero point drifts, and the zero point output voltage decays with operation. The zero point c...; onwayer stm32/stm8

940nm transmitting and receiving tube: [table=98%] [tr][td] I'm urgently looking for the model and manufacturer of the transmitting tube and receiving tube with a wavelength of 940nm, a remote control integrated head, and a fundamental wav...; kissjiangs Analog electronics

LED light strip positive and negative internal resistance detection: [color=#333333][font=微软雅黑]Hello everyone: There are LED light strip products available, powered by 36V, with a total current of about 4~5A. It is necessary to detect the internal resistance of the pos...; wzk198005 MCU

Is zero-crossing detection still required after using MOC3041?: The whole circuit is a single-chip temperature control system. I want to use MOC3041+BT136 to control the start and stop of the heating rod. Doesn't MOC3041 have the function of zero-crossing detectio...; wll711 MCU

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components