LCW896-1029-30AB95 datasheet, PDF

Datasheet> All Categories > The connector> socket> LCW896-1029-30AB95

LCW896-1029-30AB95: DescriptionIC Socket, BGA896, 896 Contact(s), ROHS COMPLIANT; CategoryThe connector socket; File Size1MB，8 Pages; ManufacturerActel; Websitehttp://www.actel.com/; Environmental Compliance

Download Datasheet Parametric View All

LCW896-1029-30AB95 Overview

IC Socket, BGA896, 896 Contact(s), ROHS COMPLIANT

LCW896-1029-30AB95 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
package instruction	ROHS COMPLIANT
Reach Compliance Code	compliant
Is Samacsys	N
Contact to complete cooperation	GOLD/TIN
Contact completed and terminated	GOLD/TIN
Contact material	BERYLLIUM COPPER
Device slot type	IC SOCKET
Type of equipment used	BGA896
Shell material	CERAMIC
JESD-609 code	e4/e3
Manufacturer's serial number	LCW
Number of contacts	896
Base Number Matches	1

Preview

Download Datasheet

View All

Socket Mounting Recommendations and Reflow Profile

Purpose

This document is meant to serve as a guide for mounting E-tec surface mount device (SMD)

sockets to the printed circuit board (PCB). The recommendations described here are guidelines

only, and modifications may be needed for your particular socket, PCB, and process.

Application

The sockets this document applies to are as follows: Clam Shell, Knob Lock, Screw Lock, Twist

Lock, Quick Lock and Lever Lock in SMD style. These sockets utilize the E-tec patented spring-

pin technology. This technology allows the pins to be soldered to the PCB while still providing

compliance to the device under test (DUT) via springs located at the other end of the pin. The

pins themselves do not have solder pre-forms as a BGA would with its solder balls. However, the

sockets are designed to mount to the same PCB footprint and pads as required by the BGA, or

any other IC package the socket was designed for (except if locating pegs are used; see ‘Locating

Pegs’ section of this document). When compared to mounting a BGA, an extra volume of solder

paste is required to mount the sockets to the PCB. To effect this, a properly dimensioned stencil

is required. Once the paste has been applied, a standard reflow process is then used to solder the

socket to the PCB. After the socket is verified to have proper electrical connection to the PCB,

the system is then ready to be used.

Locating Pegs

Although designed to mount to the same footprint as the IC, with just a small amount of

additional keep-out area, E-tec sockets can also be offered with locating pegs. The sockets are

typically mounted with two locating pegs, which require two thru-holes drilled into the PCB.

These pegs help to align the socket on the PCB, and hence align the socket’s pins to the PCB’s

pads, during the soldering process. Furthermore, plating the thru-holes allows the locating pegs

to be soldered to the PCB for better mechanical stability during everyday use and handling of the

socket. If the PCB design permits, E-tec recommends the use of these locating pegs. For fine-

pitch, low pin-count sockets without locating pegs, the mechanical strength of the solder joints

may be insufficient. In these cases, it is recommended to epoxy the socket body to the PCB. 3M

Scotch-Weld 2216 B/A is a suitable epoxy. In any case, the proper volume of solder paste is

required to ensure mechanical and electrical integrity. Recommended stencil dimensions are

given in the next section of this document.

E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland

Phone +41-21-781 08 10 ·

www.e-tec.com

info@e-tec.com

E-tec Socket Mounting Recommendations

PRELIMINARY

Recommended Resources

Hi-end power amplifier circuit

Using silicon rectifier electroplating appliances

Producing RF modulator circuit for Zhongbao camcorder

Phase detection circuit

Bidirectional thyristor speed regulating circuit

810 computer motherboard circuit diagram_09

Comparator NTE919D input and output are abnormal: This is my first time to use the comparator NTE919D. Two questions: 1. Input problem: My negative input terminal is connected to a bipolar triangle wave, and the positive terminal is connected to DC. ...; 抬头 Analog electronics

Let's play with Raspberry Pi 3+ and turn the Raspberry Pi into a powerful router: [align=left] Earlier, we implemented the function of portable WiFi based on the bridge mode. Now I will use another way to implement it, using openwrt to build a more powerful wireless router. [/align...; shenlan1986 Embedded System

Play Basic with micro:bit: This year marks the 57th anniversary of the Basic language, and many people's first programming was done with Basic on Commodore PET, Sinclair ZX Spectrum or Apple 2 in the 1970s and 1980s. It is wort...; dcexpert MicroPython Open Source section

PIC32MX250F128B please help?: I have a question about PIC32MX250F128B. I recently used this chip in a new project and need some development information. Where can I find it?...; zhanweiming Microchip MCU

Serial port sends and receives garbled data: My microcontroller's serial port always produces garbled characters when sending and receiving data. I have tried various baud rate settings, but it's still the same. How can I solve this problem?...; greenhabit Embedded System

Please tell me about the font of CPEN.: I would like to ask you about the CPEN font problem~ I am a novice who is new to WINCE. Now I want to draw a line under WINCE 5.0. My CODE is as follows. The definition of g_nPenStyle is to switch the...; yydwhy Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components