EEWORLDEEWORLDEEWORLD

Part Number

Search

530EB106M250BG

Description
LVPECL Output Clock Oscillator, 106.25MHz Nom, ROHS COMPLIANT, SMD, 6 PIN
CategoryPassive components    oscillator   
File Size268KB,15 Pages
ManufacturerSilicon Laboratories Inc
Environmental Compliance  
Download Datasheet Parametric View All

530EB106M250BG Overview

LVPECL Output Clock Oscillator, 106.25MHz Nom, ROHS COMPLIANT, SMD, 6 PIN

530EB106M250BG Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerSilicon Laboratories Inc
Reach Compliance Codeunknown
Is SamacsysN
maximum descent time0.35 ns
Frequency Adjustment - MechanicalNO
frequency stability20%
JESD-609 codee4
Manufacturer's serial number530
Installation featuresSURFACE MOUNT
Nominal operating frequency106.25 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVPECL
physical size177.8mm x 127.0mm x 41.91mm
longest rise time0.35 ns
Maximum supply voltage2.75 V
Minimum supply voltage2.25 V
Nominal supply voltage2.5 V
surface mountYES
maximum symmetry55/45 %
Terminal surfaceNickel/Gold (Ni/Au)
Base Number Matches1
S i 5 3 0 / 5 31
C
R Y S TA L
O
S C I L L A T O R
(XO)
(10 M H
Z T O
1.4 G H
Z
)
Features
Available with any-rate output
frequencies from 10 MHz to 945 MHz
and select frequencies to 1.4 GHz
3rd generation DSPLL
®
with superior
jitter performance
3x better frequency stability than
SAW-based oscillators
Internal fixed crystal frequency
ensures high reliability and low
aging
Available CMOS, LVPECL,
LVDS, and CML outputs
3.3, 2.5, and 1.8 V supply options
Industry-standard 5 x 7 mm
package and pinout
Pb-free/RoHS-compliant
Si5602
Ordering Information:
See page 7.
Applications
SONET/SDH
Networking
SD/HD video
Test and measurement
Clock and data recovery
FPGA/ASIC clock generation
Pin Assignments:
See page 6.
(Top View)
NC
OE
GND
1
2
3
6
5
4
V
DD
Description
The Si530/531 XO utilizes Silicon Laboratories’ advanced DSPLL circuitry
to provide a low jitter clock at high frequencies. The Si530/531 is available
with any-rate output frequency from 10 to 945 MHz and select frequencies to
1400 MHz. Unlike a traditional XO, where a different crystal is required for
each output frequency, the Si530/531 uses one fixed crystal to provide a
wide range of output frequencies. This IC based approach allows the crystal
resonator to provide exceptional frequency stability and reliability. In addition,
DSPLL clock synthesis provides superior supply noise rejection, simplifying
the task of generating low jitter clocks in noisy environments typically found in
communication systems. The Si530/531 IC based XO is factory configurable
for a wide variety of user specifications including frequency, supply voltage,
output format, and temperature stability. Specific configurations are factory
programmed at time of shipment, thereby eliminating long lead times
associated with custom oscillators.
®
CLK–
CLK+
Si530 (LVDS/LVPECL/CML)
OE
NC
GND
1
2
3
6
5
4
V
DD
Functional Block Diagram
V
DD
CLK– CLK+
NC
CLK
Si530 (CMOS)
Fixed
Frequency
XO
Any-rate
10–1400 MHz
DSPLL
®
Clock
Synthesis
OE
NC
GND
1
2
3
6
5
4
V
DD
CLK–
CLK+
Si531 (LVDS/LVPECL/CML)
OE
GND
Rev. 1.0 7/06
Copyright © 2006 by Silicon Laboratories
Si530/531
About the address of IOCON_SCKLOC in LPC1100 routine
When operating the spi function of SSP, I found the following statement in lpc1100.h in the example program. #define IOCON_SCKLOC (*(volatile unsigned long *)(IOCON_BASE + 0x110)) That is to say, the ...
eeleader MCU
STM32G timer setting problem
I used STM32CUBE to develop an experimental program for STM32G431. I felt that the setting was 1K Hz, and the TIM6 clock was very slow. About 50 interrupt cycles, that is, 1S, was 10 times slower. Bec...
bigbat stm32/stm8
AHB Configuration
I want to use AHB mode and GPIO register mapping to turn on the light. Which registers do I need to configure? (I am using arm cortex M3 LM3S9B96) I configured the following, but it does not work. Is ...
jiangsh FPGA/CPLD
I am confused! A newbie encountered a strange problem! Even ordinary loop statements are giving me trouble!
In Keil compilation environment, in main, besides the initialization statement, there is only one loop: unsigned char i; for(i=0;i<10;i++) {Serial_One_SendData(i); } It should loop 10 times, and outpu...
y_s_k0404 Embedded System
Solution for invalid crystal oscillator configuration of M8
Yesterday I helped a friend write something. It was my first time using Zhifeng. I accidentally locked the crystal oscillator of M8 to an external clock, and I couldn't download the program. I was ver...
heicnhei Microchip MCU
How to add test points to a schematic
Experts, how do I add test points in the schematic? Are they the round test points? Can they be packaged? Can they be directly imported into the PCB? If I add test points in the PCB, it is easy to mis...
papermay PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2754  1523  2145  636  844  56  31  44  13  17 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号