MC74F195
4-BIT PARALLEL
ACCESS SHIFT REGISTER
The functional characteristics of the MC74F195 4-Bit Parallel Access Shift
Register are indicated in the Logic Diagram and Function Table. The device
is useful in a wide variety of shifting, counting, and storage applications. It per-
forms serial, parallel, serial-to-parallel, or parallel-to-serial data transfers at
very high speeds.
The MC74F195 operates in two primary modes, shift right (Q0-Q1) and par-
allel load, which are controlled by the state of the Parallel Enable (PE) input.
Serial data enters the first flip-flop (Q0) via the J and K inputs when the PE
input is HIGH, and is shifted 1 bit in the direction Q0-Q1-Q2-Q3 following each
LOW-to-HIGH clock transition. The J and K inputs provide the flexibility of the
JK type input is made for special applications, and by tying the two pins togeth-
er the simple D-type input is made for general applications. The device ap-
pears as four common clocked D flip-flops when the PE input is LOW. After
the LOW-to-HIGH clock transition, data on the parallel inputs (D0-D3) is trans-
ferred to the respective Q0-Q3 outputs. Shift left operation (Q3-Q2) can be
achieved by tying the Qn outputs to the Dn-1 inputs and holding the PE input
LOW.
All parallel and serial data transfers are synchronous, occurring after each
LOW-to-HIGH clock transition. The MC74F195 utilizes edge-triggering;
therefore, there is no restriction on the activity of the J, K, Dn, and PE inputs
for logic operation, other than the setup and hold time requirements.
A LOW on the asynchronous Master Reset (MR) input sets all Q outputs
LOW, independent of any other input condition.
•
Shift Right and Parallel Load Capability
•
J-K (D-Type) Inputs to First Stage
•
Complement Output from Last Stage
•
Asynchronous Master Reset
4-BIT PARALLEL
ACCESS SHIFT REGISTER
FAST™ SCHOTTKY TTL
J SUFFIX
CERAMIC
CASE 620-09
16
1
16
1
N SUFFIX
PLASTIC
CASE 648-08
16
1
D SUFFIX
SOIC
CASE 751B-03
ORDERING INFORMATION
CONNECTION DIAGRAM DIP
VCC
16
Q0
15
Q1
14
Q2
13
Q3
12
Q3
11
CP
10
PE
9
MC74FXXXJ
MC74FXXXN
MC74FXXXD
Ceramic
Plastic
SOIC
LOGIC SYMBOL
9
2
1
MR
2
J
3
K
4
D0
5
D1
6
D2
7
D3
8
GND
10
3
J
4 5
6
7
PE D0 D1 D2 D3
11
Q3
CP
K
MR Q0 Q1 Q2 Q3
1 15 14 13 12
VCC = PIN 16
GND = PIN 8
FAST AND LS TTL DATA
4-104
MC74F195
GUARANTEED OPERATING RANGES
Symbol
VCC
TA
IOH
IOL
Supply Voltage
Operating Ambient Temperature Range
Output Current
High
Output Current
Low
Parameter
74
74
74
74
Min
4.5
0
Typ
5.0
25
Max
5.5
70
–1.0
20
Unit
V
°C
mA
mA
LOGIC DIAGRAM
J
PE
K
D0
D1
D2
D3
CP
MR
R
RD
Q
R
RD
R
RD
R
RD
Q
CP
S
Q
Q0
CP
S
Q
Q1
CP
S
Q
Q2
CP
S
Q
Q3 Q3
FUNCTION TABLE
Inputs
Operating Modes
Asynchronous Reset
Shift, Set First Stage
Shift, Reset First Stage
Shift, Toggle First Stage
Shift, Retain First Stage
Parallel Load
MR
L
H
H
H
H
H
CP
X
↑
↑
↑
↑
↑
PE
X
h
h
h
h
l
J
X
h
l
h
l
X
K
X
h
l
l
h
X
Dn
X
X
X
X
X
dn
Q0
L
H
L
q0
q0
d0
Q1
L
q0
q0
q0
q0
d1
Outputs
Q2
L
q1
q1
q1
q1
d2
Q3
L
q2
q2
q2
q2
d3
Q3
H
q2
q2
q2
q2
d3
H = HIGH Voltage Level
L = LOW Voltage Level
X = Don’t Care
dn (qn) = Lower case letters indicate the state of the referenced input (or output) one setup time prior to the LOW-to-HIGH clock transition.
↑
= LOW-to-HIGH clock transition
FAST AND LS TTL DATA
4-105
MC74F195
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE
(unless otherwise specified)
Limits
Symbol
VIH
VIL
VIK
VOH
Parameter
Input HIGH Voltage
Input LOW Voltage
Input Clamp Diode Voltage
Output HIGH Voltage
74
74
VOL
IIH
Output LOW Voltage
Input HIGH Current
2.5
2.7
0.5
20
100
IIL
IOS
ICC
Input LOW Current
Output Short Circuit Current (Note 2)
Power Supply Current
–60
–0.6
–150
38
mA
mA
mA
Min
2.0
0.8
–1.2
Typ
Max
Unit
V
V
V
V
V
V
µA
IOL = 20 mA
VIN = 2.7 V
VIN = 7.0 V
VCC = MAX
VOUT = 0 V
VCC = MAX
VCC = MAX
Test Conditions
Guaranteed Input HIGH Voltage
Guaranteed Input LOW Voltage
IIN = –18 mA
IOH = –1.0 mA
VCC = MIN
VCC = 4.5 V
VCC = 4.75 V
VCC = 4.5 V
VCC = MAX
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under guaranteed operating ranges.
2. Not more than one output should be shorted at a time, nor for more than 1 second.
AC CHARACTERISTICS
54/74F
TA = + 25°C
VCC = + 5.0 V
CL = 50 pF
Symbol
fmax
tPLH
tPHL
tPHL
tPLH
Propagation Delay
CP to Q/Q
Propagation Delay, MR to Q
Propagation Delay, MR to Q
Parameter
Min
105
2.5
2.5
3.0
3.0
7.0
8.0
10
10.5
Max
Min
90
2.5
2.5
3.0
3.0
8.0
9.0
11
11
ns
ns
74F
TA = 0°C to + 70°C
VCC = 5.0 V
±
10%
CL = 50 pF
Max
Unit
MHz
ns
FAST AND LS TTL DATA
4-106
MC74F195
AC OPERATING REQUIREMENTS
74F
TA = + 25°C
VCC = + 5.0 V
CL = 50 pF
Symbol
ts (H)
ts (L)
th (H)
th (L)
ts (H)
ts (L)
th (H)
th (L)
tw (H)
tw (L)
trec
CP Pulse Width, HIGH
MR Pulse Width, LOW
Recovery Time, MR to CP
Hold Time, HIGH or LOW PE to CP
Setup Time, HIGH or LOW PE to CP
Hold Time, HIGH or LOW J, K, D to CP
Parameter
Setup Time, HIGH or LOW J, K, D to CP
Min
4.0
4.0
0
0
8.0
8.0
0
0
5.0
5.0
7.0
Max
Min
4.0
4.0
1.0
1.0
9.0
9.0
0
0
5.5
5.0
8.0
ns
ns
ns
ns
ns
ns
74F
TA = 0°C to + 70°C
VCC = 5.0 V
±
10%
CL = 50 pF
Max
Unit
ns
FAST AND LS TTL DATA
4-107
Talking
京公网安备 11010802033920号
EEWORLD
