FUJITSU SEMICONDUCTOR
DATA SHEET
DS07-12609-3E
8-bit Microcontroller
CMOS
F
2
MC-8FX MB95160M Series
MB95F168M/F168N/F168J/FV100D-103
■
DESCRIPTION
The MB95160M series is general-purpose, single-chip microcontrollers. In addition to a compact instruction set,
the microcontrollers contain a variety of peripheral functions.
Note : F
2
MC is the abbreviation of FUJITSU Flexible Microcontroller.
■
FEATURE
•
F
2
MC-8FX CPU core
Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instruction
• Bit manipulation instructions etc.
•
Clock
• Main clock
• Main PLL clock
• Sub clock
• Sub PLL clock
(Continued)
Be sure to refer to the “Check Sheet” for the latest cautions on development.
“Check Sheet” is seen at the following support page
URL : http://www.fujitsu.com/global/services/microelectronics/product/micom/support/index.html
“Check Sheet” lists the minimal requirement items to be checked to prevent problems beforehand in system
development.
Copyright©2007 FUJITSU LIMITED All rights reserved
MB95160M Series
(Continued)
•
Timer
• 8/16-bit compound timer
×
2 channels
Can be used to interval timer, PWC timer, PWM timer and input capture.
• 8/16-bit PPG
×
2 channels
• 16-bit PPG
×
1 channel
• Time-base timer
×
1 channel
• Watch prescaler
×
1 channel
•
LIN-UART
×
1 channel
• LIN function, clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
• Full duplex double buffer
•
UART/SIO
×
1 channel
• Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
• Full duplex double buffer
2
C*
×
1 channel
•
I
Built-in wake-up function
•
External interrupt
×
8 channels
• Interrupt by edge detection (rising, falling, or both edges can be selected)
• Can be used to recover from low-power consumption (standby) modes.
•
8/10-bit A/D converter
×
8 channels
8-bit or 10-bit resolution can be selected.
•
LCD controller (LCDC)
• 32 SEG
×
4 COM (Max 128 pixels)
• With blinking function
•
Low-power consumption (standby) mode
• Stop mode
• Sleep mode
• Watch mode
• Time-base timer mode
•
I/O port
• The number of maximum ports : Max 53
• Port configuration
- General-purpose I/O ports (N-ch open drain) : 2 ports
- General-purpose I/O ports (CMOS)
: 51 ports
•
Programmable input voltage levels of port
Automotive input level
/
CMOS input level
/
hysteresis input level
•
Flash memory security function
Protects the content of Flash memory
* : Purchase of Fujitsu I
2
C components conveys a license under the Philips I
2
C Patent Rights to use, these
components in an I
2
C system provided that the system conforms to the I
2
C Standard Specification as defined
by Philips.
2
MB95160M Series
■
PRODUCT LINEUP
Part number*
1
Parameter
Type
ROM capacity
RAM capacity
Reset output
Option*
2
Clock system
Low voltage
detection reset
Clock supervisor
No
No
Yes
Dual clock
Yes
Yes
MB95F168M
MB95F168N
Flash memory product
60 Kbytes
2 Kbytes
No
MB95F168J
CPU functions
Number of basic instructions
: 136
Instruction bit length
: 8 bits
Instruction length
: 1 to 3 bytes
Data bit length
: 1, 8, and 16 bits
Minimum instruction execution time : 61.5 ns (at machine clock frequency 16.25
MHz)
Interrupt processing time
: 0.6
µs
(at machine clock frequency 16.25 MHz)
General-purpose I/O port (N-ch open drain) : 2 ports
General-purpose I/O port (CMOS)
: 51 ports
Programmable input voltage levels of port :
Automotive input level
/
CMOS input level
/
hysteresis input level
Interrupt cycle : 0.5 ms, 2.1 ms, 8.2 ms, 32.8 ms (at main oscillation clock 4 MHz)
Reset generated cycle
At main oscillation clock 10 MHz
: Min 105 ms
At sub oscillation clock 32.768 kHz (for dual clock product) : Min 250 ms
Capable of replacing 3 bytes of ROM data
Master/slave sending and receiving
Bus error function and arbitration function
Detecting transmitting direction function
Start condition repeated generation and detection functions
Built-in wake-up function
Data transfer capable in UART/SIO
Full duplex double buffer,
variable data length (5/6/7/8-bit), built-in baud rate generator
NRZ type transfer format, error detected function
LSB-first or MSB-first can be selected.
Clock synchronous (SIO) or clock asynchronous (UART) serial data transfer capable
Dedicated reload timer allowing a wide range of communication speeds to be set.
Full duplex double buffer.
Capable of serial data transfer synchronous or asynchronous to clock signal.
LIN functions available as the LIN master or LIN slave.
Ports (Max 53 ports)
Time-base timer
(1 channel)
Watchdog timer
Wild register
Peripheral functions
I
2
C
(1 channel)
UART/SIO
(1 channel)
LIN-UART
(1 channel)
8/10-bit A/D converter
8-bit or 10-bit resolution can be selected.
(8 channels)
(Continued)
3
MB95160M Series
(Continued)
Part number*
1
Parameter
MB95F168M
MB95F168N
MB95F168J
LCD controller
(LCDC)
COM output
: 4 (Max)
SEG output
: 32 (Max)
LCD drive power supply (bias) pin
:4
32 SEG
×
4 COM : 128 pixels can be displayed.
Duty LCD mode
Operable in LCD standby mode
With blinking function
Built-in division resistance for LCD drive
Each channel of the timer can be used as “8-bit timer
×
2 channels” or “16-bit timer
×
1 channel”.
Built-in timer function, PWC function, PWM function, capture function, and square
wave form output
Count clock : 7 internal clocks and external clock can be selected.
PWM mode or one-shot mode can be selected.
Counter operating clock : Eight selectable clock sources
Support for external trigger start
Each channel of the PPG can be used as
“
8-bit PPG
×
2 channels
”
or
“
16-bit PPG
×
1
channel
”
.
Counter operating clock : Eight selectable clock sources
Count clock : Four selectable clock sources (125 ms, 250 ms, 500 ms, or 1 s)
Counter value can be set from 0 to 63. (Capable of counting for 1 minute when
selecting clock source 1 second and setting counter value to 60)
4 selectable interval times (125 ms, 250 ms, 500 ms, or 1 s)
Interrupt by edge detection (rising, falling, or both edges can be selected.)
Can be used to recover from standby modes.
Supports automatic programming, Embedded Algorithm
Write/Erase/Erase-Suspend/Resume commands
A flag indicating completion of the algorithm
Number of write/erase cycles (Minimum) : 10000 times
Data retention time: 20 years
Erase can be performed on each block
Block protection with external programming voltage
Flash Security Feature for protecting the content of the Flash
Sleep, stop, watch, and time-base timer
Peripheral functions
4
8/16-bit compound
timer (2 channels)
16-bit PPG
(1 channel)
8/16-bit PPG
(2 channels)
Watch counter
Watch prescaler
(1 channel)
External interrupt
(8 channels)
Flash memory
Standby mode
*1 : MASK ROM products are currently under consideration.
*2 : For details of option, refer to “■ MASK OPTION”.
Note : Part number of evaluation product in MB95160M series is MB95FV100D-103. When using it, the MCU board
(MB2146-303A) is required.
MB95160M Series
■
OSCILLATION STABILIZATION WAIT TIME
The initial value of the main clock oscillation stabilization wait time is fixed to the maximum value. The maximum
value is shown as follows.
Oscillation stabilization wait time
Remarks
(2
14
-2) /F
CH
Approx. 4.10 ms (at main oscillation clock 4 MHz)
■
PACKAGES AND CORRESPONDING PRODUCTS
Part number
Package
FPT-64P-M23
FPT-64P-M24
BGA-224P-M08
: Available
: Unavailable
MB95F168M/F168N/F168J
MB95FV100D-103
5
京公网安备 11010802033920号
EEWORLD
