EEWORLDEEWORLDEEWORLD

Part Number

Search

TSOP4840SS1BS21

Description
Photo IC, TRANSISTOR-STAGE OUTPUT PHOTO IC,LED-7B
CategoryLED optoelectronic/LED    photoelectric   
File Size134KB,7 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

TSOP4840SS1BS21 Overview

Photo IC, TRANSISTOR-STAGE OUTPUT PHOTO IC,LED-7B

TSOP4840SS1BS21 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
JESD-609 codee3
Installation featuresTHROUGH HOLE MOUNT
Maximum operating temperature85 °C
Minimum operating temperature-25 °C
Maximum slew rate0.00105 mA
Nominal supply voltage4.1 V
surface mountNO
Terminal surfaceTin (Sn) - with Silver (Ag) barrier
Base Number Matches1
New TSOP48.., TSOP44..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Low supply current
• Photo detector and preamplifier in one
package
• Internal filter for PCM frequency
• Improved shielding against EMI
1
2
3
16672
• Supply voltage: 2.7 V to 5.5 V
• Improved immunity against ambient light
• Insensitive to supply voltage ripple and noise
• Compliant to RoHS directive 2002/95/EC and in
accordance to WEEE 2002/96/EC
MECHANICAL DATA
Pinning
1 = OUT, 2 = GND, 3 = V
S
DESCRIPTION
The TSOP48.., TSOP44.. series are miniaturized receivers
for infrared remote control systems. A PIN diode and a
preamplifier are assembled on a lead frame, the epoxy
package acts as an IR filter.
The demodulated output signal can be directly decoded by
a microprocessor. The TSOP48.. is compatible with all
common IR remote control data formats. The TSOP44.. is
optimized to suppress almost all spurious pulses from
energy saving fluorescent lamps but will also suppress
some data signals.
This component has not been qualified according to
automotive specifications.
PARTS TABLE
CARRIER FREQUENCY
30 kHz
33 kHz
36 kHz
36.7 kHz
38 kHz
40 kHz
56 kHz
STANDARD APPLICATIONS (AGC2/AGC8)
TSOP4830
TSOP4833
TSOP4836
TSOP4837
TSOP4838
TSOP4840
TSOP4856
VERY NOISY ENVIROMENTS (AGC4)
TSOP4430
TSOP4433
TSOP4436
TSOP4437
TSOP4438
TSOP4440
TSOP4456
BLOCK DIAGRAM
16833_5
APPLICATION CIRCUIT
17170_7
R
1
IR receiver
V
S
+ V
S
C
1
OUT
GND
V
O
µC
GND
3
33 kΩ
V
S
1
Input
AGC
Band
pass
Demo-
dulator
OUT
Transmitter
with
TSALxxxx
2
PIN
Control circuit
GND
The external components R
1
and C
1
are optional
to improve the robustnes against electrical overstress
(typical values are R
1
= 100
Ω,
C
1
= 0.1 µF).
The output voltage V
O
should not be pulled down to a level
below 1 V by the external circuit.
The capacitive load at the output should be less than 2 nF.
Document Number: 82090
Rev. 2.6, 11-Nov-09
Circuit
www.vishay.com
1
[Project Outsourcing] Implementing TCP/IP IPV4 or IPV6 protocol stack in FPGA
Implementing TCP/IP IPV4 or IPV6 protocol stack in FPGAProject budget:¥ 3,000~20,000 Development cycle: 45 days Project Category: Embedded Bidding requirements:Project tags:Xilinx FPGA TCP/IP protocol...
CSTO项目交易 FPGA/CPLD
Say a celebrity silently and the computer will guess it for you
[url]http://en.akinator.com/#[/url]...
凯哥 Talking
S5PV210 mounts two peripherals on IIC1 s3c-i2c s3c2440-i2c.1: cannot get bus (error -110) error
s3c-i2c s3c2440-i2c.1: cannot get bus (error -110) ——But it can be used normally under wince, I don’t know why, it’s really annoying, now reducing the speed of IIC1 doesn’t work. Just disconnect one I...
gooogleman Embedded System
Why is it so difficult to put out a fire when a new energy vehicle catches fire?
[i=s]This post was last edited by alan000345 on 2018-7-2 13:08[/i] It turns out that Mr. Zhang, the chief designer of electric vehicles, said that the design of lithium battery packs for electric vehi...
alan000345 Automotive Electronics
【Using IP core to realize D/A conversion in measurement and control system】
Abstract: Digital technology is used to realize D/A conversion in the measurement and control system with IP core, and it is implemented in a programmable logic device. It is not affected by temperatu...
dfjso9 Analog electronics
Under wince5.0, the hard disk file system must be reloaded every time the computer is turned on.
I wrote a hard disk driver under wince5.0, which can load a 16G hard disk. However, every time I boot up, I have to wait 10 minutes to load the file system. The serial port output is constantly readin...
hurdy Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 757  130  2916  1478  90  16  3  59  30  2 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号