EEWORLDEEWORLDEEWORLD

Part Number

Search

DWM-04-56-G-D-505

Description
Board Stacking Connector, 8 Contact(s), 2 Row(s), Male, Straight, Solder Terminal,
CategoryThe connector    The connector   
File Size130KB,1 Pages
ManufacturerSAMTEC
Websitehttp://www.samtec.com/
Environmental Compliance  
Download Datasheet Parametric View All

DWM-04-56-G-D-505 Overview

Board Stacking Connector, 8 Contact(s), 2 Row(s), Male, Straight, Solder Terminal,

DWM-04-56-G-D-505 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Reach Compliance Codecompliant
ECCN codeEAR99
Connector typeBOARD STACKING CONNECTOR
Contact to complete cooperationGOLD (10) OVER NICKEL (50)
Contact completed and terminatedGOLD FLASH OVER NICKEL (50)
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee4
MIL complianceNO
Manufacturer's serial numberDWM
Plug informationNO
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of rows loaded2
OptionsGENERAL PURPOSE
Terminal pitch1.27 mm
Termination typeSOLDER
Total number of contacts8
Base Number Matches1
【AT-START-F403A Review】II. Exploration of Simulated Virtual Serial Port
In the last review, I installed a virtual serial port. Of course, it was installed automatically, not by my own will. At that time, I had a question mark in my mind, I thought, ATLINK can actually cre...
ddllxxrr Domestic Chip Exchange
I want to make a control board with DSP28335. Can anyone give me some advice?
I am a beginner in DSP and don't know anything. I want to make a control board using 28335 to control two motors. The drivers of the motors are already available, so I just need to use CAN to send ins...
flyfish1986 Microcontroller MCU
Ask: About cross-compiling Perl
I now want to use perl5.10.0 on a mipsel board. I read the Cross-compilation section in the INSTALL document in its source code (you can also see http://search.cpan.org/~rgarcia/perl/INSTALL#Cross-com...
losty Embedded System
When amplifying small signals, is it better to use three op amps or a direct follower + op amp?
[i=s] This post was last edited by paulhyde on 2014-9-15 04:16 [/i] I have a question: Now I want to amplify a 5mv voltage signal. Is it better to use three op07s to build a three-op-amp amplifier cir...
truy203 Electronics Design Contest
Touch screen wooden radio
Touch-type wooden radio The shell of this cool radio is made entirely of wood. There are some wavy folds on the top. When we slide our fingers over these wavy folds, we can adjust the volume and chang...
xyh_521 Creative Market
Interrupt signal generation and clearing after acknowledgement
always @(negedge rstn or posedge clk_in)beginif (rstn == 1'b0)beginapp_int_sts_rapp_int_reqendelsebeginapp_int_sts_rif (app_int_sts_buf == 1'b1 & app_int_sts_r == 1'b0)beginapp_int_reqendelse if (app_...
eeleader FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 365  1341  2334  1794  910  8  27  47  37  19 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号