To order, simply select desired option from each category and place in the appropriate box. Available options are shown and
described on pages L-13 thru L-17. For additional options not shown in catalog, consult Customer Service Center.
Switch Function
MA00
SP, 10 pos., 36°
MA02
SP, 2 pos., 36°
MA03
SP, 3 pos., 36°
MA04
SP, 4 pos., 36°
MA05
SP, 5 pos., 36°
MA06
SP, 6 pos., 36°
MA10
SP, 10 pos., 36°
MB00
DP, 5 pos., 36°
MB03
DP, 3 pos., 36°
MB04
DP, 4 pos., 36°
MB05
DP, 5 pos., 36°
MC00
SP, 12 pos., 30°
MC03
SP, 3 pos., 30°
MC07
SP, 7 pos., 30°
MC12
SP, 12 pos., 30°
MD00
DP, 6 pos., 30°
MD06
DP, 6 pos., 30°
ME00
SP, 10 pos., 36°
ME04
SP, 4 pos., 36°
MF00
DP, 5 pos., 36°
MG00
SP, 12 pos., 30°
MH00
DP, 6 pos., 30°
Actuator & Bushing
L1
.650"
long, flatted
L2
Screwdriver slot, flush
L3
.650" long, round
S1
.650" long, flatted
S2
Screwdriver slot, flush
S3
.650" long, round
S6
.785" long, slot
Short/Non-short
N
Non-shorting contacts
Terminations
Z
Solder lug
C
PC Thru-hole
Contact Material
Q
Silver
G
Gold over silver
Seal
D
No seal
F
Splashproof shaft & panel seal
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
L–12
www.ittcannon.com
C&K M Series
Half-inch Rotary Switches
SWITCH FUNCTION
36º INDEXING
MODEL NO.
WITH STOP
PINS
MODEL NO.
WITH STOP
RINGS
SP MODELS 36º INDEXING
SCHEMATIC
30º INDEXING
MODEL NO.
WITH STOP
PINS
MODEL NO.
WITH STOP
RINGS
NO.
POLES
SWITCH
FUNCTION
10 Positions
No Stops
2 Positions
3 Positions
4 Positions
5 Positions
6 Positions
10 Positions
5 Positions
No Stops
3 Positions
SP MODELS 30º INDEXING
SCHEMATIC
DP MODELS 36º INDEXING
SCHEMATIC
NO.
POLES
SWITCH
FUNCTION
12 Positions
No Stops
3 Positions
7 Positions
12 Positions
6 Positions
No Stops
6 Positions
MA00
MA02
MA03
SP
ME00
—
—
MC00
SP
MG00
—
—
—
MC03
MC07
MC12
MD00
MA04
MA05
MA06
MA10
MB00
MB03
ME04
—
—
—
MH00
—
DP
MD06
MF00
DP
MB04
MB05
—
—
4 Positions
5 Positions
DP MODELS 30º INDEXING
SCHEMATIC
All models
with all options when ordered with S1-SB stainless steel actuator options.
NOTE:
Number of positions or stops preset at factory (NOTE: MX00 models have full 360 rotation with no stops. Stop pins or stop rings supplied for user-selectable stops, see above).
All terminals present regardless of number of switch positions. Hardware is available separately, see section “Technical Data and Additional Hardware”.
L
Rotary
Rotary
SP, 36º Indexing
Actuator Shown In Pos. 1
DP, 36º Indexing
Terminal Numbers Marked
On Side Of Housing
Part number shown: MA00L1NZQD
SP, 30º Indexing
Actuator Shown In Pos. 1
DP, 30º Indexing
Terminal Numbers Marked
On Side Of Housing
Part number shown: MC00L1NZQD
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
L–13
www.ittcannon.com
C&K M Series
Half-inch Rotary Switches
ACTUATOR (ZINC ALLOY)
L1
.650" LONG, FLATTED
L2
SCREWDRIVER SLOT, FLUSH
L3
.650" LONG, ROUND
All actuators shown in pos. 1
L
Rotary
S1
.650" LONG, FLATTED
ACTUATOR (STAINLESS STEEL)
S2
SCREWDRIVER SLOT, FLUSH
S3
.650" LONG, ROUND
S6
.785" LONG, SLOT
All actuators shown in pos. 1
All models UL/CSA when ordered with stainless steel actuators.
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
L–14
www.ittcannon.com
C&K M Series
Half-inch Rotary Switches
SHORTING/NON-SHORTING CONTACTS
N
NON-SHORTING CONTACTS
Break-before-make
TERMINATIONS
Z
SOLDER LUG
SP
DP
C
PC THRU-HOLE
SP
DP
PANEL MOUNTING
WITH FLATS
0.213
(5.41)
PC MOUNTING
36
º
INDEXING
SP
DP
WITHOUT FLATS
0.260 DIA
(6.59)
0.260 DIA
(6.60)
SP
Hardware: All models, one mounting nut and lockwasher
supplied standard. MA00 thru MD00 models: two stop pins
and adhesive mylar washer supplied. ME00 thru MH00
models: two stop rings supplied. Hardware is available
separately, see section “Technical Data and Additional
Hardware”.
PC MOUNTING
30
º
INDEXING
DP
L
Rotary
Rotary
NOTE:
Q contact material standard. Terminal numbers marked on side of housing.
All terminals insert molded. All terminals present regardless of number of switch positions.
Actuators and schematics shown in pos. 1.
CONTACT MATERIAL
OPTION
CODE
RoHS
COMPLIANT*
YES
RoHS
COMPATIBLE*
YES
YES
CONTACT
MATERIAL
SILVER
1, 2
TERMINAL
PLATING
SILVER
2
RATING
POWER
LOW LEVEL/DRY CIRCUIT
OR POWER
CARRY: 6 AMPS CONTINUOUS. SWITCH: 250 mA @ 125 V AC
or 28 V DC.
0.4 VA MAX. @ 20 V AC or DC MAX. or, CARRY: 6 AMPS
CONTINUOUS. SWITCH: 250 mA @ 125 V AC or 28 V DC.
Q
G
YES
GOLD
OVER
SILVER
3,
4
GOLD
4
* Note: See Technical Data section of this catalog for RoHS compliant and compatible definition and specifications.
This program completes the task of writing to EEPROM using IIC. First, it writes the address of IIC slave, then writes the address of EEPROM, and finally writes data. However, I don't understand the p...
[align=left][backcolor=rgb(255,255,255)]After the multi-core processor is triggered to communicate by an interrupt, the corresponding registers are configured to complete the communication. TMS320C667...
A small ultra-wideband low-noise transistor amplifier was designed and manufactured. It adopts all-microstrip matching network and negative feedback technology, uses a new transistor device HEMT, and ...
1. Identify the interface . Like the 56Kbps kitten, the ADSL Modem (also called the big cat) also has three options: built-in, USB interface and Ethernet interface. The built-in method uses the PCI ...
This post mainly shares a typical case encountered in an actual project. It briefly introduces the project purpose, demand analysis, and main technical implementation. Welcome everyone to learn and gu...
Dong Yang, executive vice president of the China Association of Automobile Manufacturers, said on the 26th that according to the authorization of the Ministry of Industry and Information Technology...[Details]
In our common sense, the word technology often has two definitions. The first is the technology sealed in the laboratory. They are like flowers on the mountain top. Only a few people on the mountai...[Details]
1. Problem When developing STM32 with IAR, I found that I could not print floating point numbers by redirecting printf to the serial port. The code is as follows: The output is as follows: It can...[Details]
background After the hardware engineer completed the PCB and schematic design, the routine was modified according to the tutorial of Zhengdian Atom to verify the correctness of the hardware. STM32F...[Details]
In the development of artificial intelligence, talent reserve is undoubtedly an important part. Artificial intelligence should be a bottom-level technology that can be deeply embedded in any indust...[Details]
What is SYSTICK: This is a 24-bit system tick timer, SysTick, with automatic reload and overflow interrupt functions. All microcontrollers based on the Cortex_M3 processor can obtain a certain time ...[Details]
The day before yesterday, another mainland technology company submitted a prospectus to the Hong Kong Stock Exchange. The company is called "Jia Nan Creative (hereinafter referred to as 'Jia Nan')"...[Details]
When Amazon quietly launched a product called Elastic Computing Cloud 12 years ago, the Internet industry in China, across the ocean, also ushered in an unprecedented development opportunity. Let's...[Details]
Independent watchdog (IWDG) and low power mode are often used in STM32 development. The watchdog is to detect and solve faults caused by software errors, and the low power mode is to enter sleep mode...[Details]
When STM32 uses JTMS (PA13) and JTCK (PA14) as normal I/O ports, add the following code before initialization (the order cannot be reversed): RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE); G...[Details]
The first one is a DMA mode of multiple channel acquisition void ADC_DMA_Config(void) { ADC_InitTypeDef ADC_InitStructure; RCC_HSICmd(ENABLE); while (RCC_GetFlagStatus(RCC_FLAG_HSIRDY) == RESET); ...[Details]
****************************************************************** 1. The operand is in register, R0--R7 2. Operands are in internal RAM 3. Operands are in external RAM But they are all similar. For ...[Details]
One addend is in the on-chip RAM 40H, 41H, 42H units, the other addend is in the on-chip RAM 43H, 44H, 45H, and the sum is stored in the 50H, 51H, 52H units, with the carry bit stored in 00H. Please ...[Details]
Design a second and minute pulse generator for a single-chip microcomputer using the interrupt method. Assume that P1.0 generates a positive pulse of one machine cycle per second, and P1.1 generates ...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
