1. The SRAM is immune to latchup to particles >111MeV-cm
2
/mg.
2. 90% worst case particle environment, Geosynchronous orbit, 100 mils of
Aluminum and default EDAC scrub rate.
SUPPLY SEQUENCING
No supply voltage sequencing is required between V
DD1
and
V
DD2
.
POWER-UP REQUIREMENTS
During power-up of the UT8ER512K32 device, the power
supply voltages will transverse through voltage ranges where
the device is not guaranteed to operate before reaching final
levels. Since some circuits on the device will start to operate at
lower voltage levels than others, the device may power-up in an
unknown state. To eliminate this with most power-up situations,
the device employs an on-chip power-on-reset (POR) circuit.
The POR, however, requires time to complete the operation.
Therefore, it is recommended that all device activity be delayed
by a minimum of 100ms, after both V
DD1
and V
DD2
supplies
have reached their respective minimum operating voltage.
4
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD1
V
DD2
V
I/O
T
STG
P
D2
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage (Core)
DC supply voltage (I/O)
Voltage on any pin
Storage temperature
Maximum package power dissipation
permitted @ Tc = +125
o
C
Maximum junction temperature
Thermal resistance, junction-to-case
2
DC input current
LIMITS
-0.3 to 2.1V
-0.3 to 3.8V
-0.3 to 3.8V
-65 to +150°C
5W
+150°C
5°C/W
±
10 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Per MIL-STD-883, Method 1012, Section 3.4.1, P
D
= (T
JC
(max) - Tc (max))
Θ
JC
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD1
V
DD2
T
C
V
IN
PARAMETER
DC supply voltage (Core)
DC supply voltage (I/O)
Case temperature range
DC input voltage
LIMITS
1.7 to 1.9V
1
3.0 to 3.6V
(C) Screening: -55 to +125°C
(W) Screening: -40 to +125°C
0V to V
DD2
Notes:
1. For increased noise immunity, supply voltage V
DD1
can be increased to 2.0V. All characteristics contained herein are guaranteed by characterization at V
Has anyone used the file system to read and write SD cards? For example, if I write something now, how can I continue writing to that location next time?...
Main features: Support ISO7816 standard and can operate up to 6 SAM cards (PSAM or ESAM) at the same time. The ASIC chip supports high-speed (38400) and low-speed (9600) SAM cards. The package form is...
[i=s] This post was last edited by dontium on 2016-2-3 23:51 [/i] [align=left]1. msp430x2274 uses I2C bus to control DLP [/align] [align=left] The block diagram analysis of DLP LightCrafter Display 30...
After the last article on TCP, I am very close to connecting to Alibaba Cloud. Today I tried to connect to Alibaba Cloud platform. I would like to thank a big guy here: Part of the code of sipower clo...
introduction
my country has a vast territory and a large population. The scale of housing construction is huge, and the amount of residential construction is large and wide. It is still on t...[Details]
1 Introduction
The high temperature tester is mainly used for temperature tracking measurement and data acquisition during the heating process. By systematically analyzing the test data, the...[Details]
As a wireless broadband metropolitan area network standard, WiMAX technology has greater advantages than previous 3.5GHz MMDS products in terms of non-line-of-sight transmission and spectrum utiliz...[Details]
The Mobile Industry Processor Interface (MIPI) Alliance is an organization responsible for promoting the standardization of software and hardware in mobile devices. It has released the D-PHY specif...[Details]
introduction
For the voltage regulator modules (VRMs) that power the latest computer central processing units (CPUs), power supply designers have historically used multiphase interleaved b...[Details]
1 Introduction
Ultrasonic waves have strong directivity, slow energy consumption, and can propagate over long distances in a medium, so they are used for distance measurement. Ultrasonic detec...[Details]
The automotive lighting and signal control system is responsible for controlling the vehicle's lighting, signal lights, electric horns, reversing and brake buzzers. Traditional automotive lighting...[Details]
The typical fault troubleshooting listed below is for reference of maintenance personnel.
When the computer is turned on, the indicator light is off and there is no screen display
Mainte...[Details]
Among the many members of the single-chip microcomputer family, the MCS-51 series of single-chip microcomputers has occupied the main market of industrial measurement and control and automation eng...[Details]
From the previous section, we have learned that the timer/counter in the microcontroller can have multiple uses, so how can I make them work for the purpose I need? This requires setting the timer/...[Details]
In today's body control module (BCM) designs, savvy engineers are moving away from electromechanical relays whenever possible. Their next step is to eliminate fuses. But is eliminating fuses a nece...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
Today, with energy becoming increasingly scarce, the utilization of natural energy has become the focus of people's attention. Among various natural energies, the endless solar energy is highly fav...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
