TD1600ALF-4
Tuner module for digital terrestrial (OFDM) applications
Rev.c — 23-04-2007
Preliminary data sheet
1. General description
TD1600ALF-4 belong to the new generation of terrestrial tuners designed to cope with
digital COFDM and analog transmission standards.
From function point-of-view these tuners can be divided into two high-frequency
sections, a RF-loopthrough and a single conversion tuner part.
In the loopthrough section broadband low-noise amplifiers are used. The loopthrough
frequency response covers the entire frequency range from VHF to UHF.
The RF-downstream section is equipped with a state-of-the-art single conversion tuner,
which makes use of a highly integrated MOPLL IC that provides the required high level
of performance necessary for COFDM signal processing.
The tuners are provided with a DC/DC converter to generate the tuning voltage
internally.
The internal 4MHz PLL crystal reference frequency is fed through one of the pin-
nd
terminals and can be used as a clock for a 2 device e.g. the channel decoder.
Two IF-outputs are provided, one is a wideband, non filtered IF-output, while the other,
narrow-band IF-output is equipped with a SAW-filter and a gain controllable IF-amplifier.
This narrow-IF-output matches the A-to-D converter input of currently available channel
decoders.
All tuners out of this family can be equipped with two standard IEC-connectors, RF-in is
IEC-female, RF-out is IEC-male. The tuner housing is available in a vertical or
horizontal mountable execution; the pinning pitch corresponds to the World Standard
Pinning convention.
Apart from the RF-connectors, all other terminals are made with wire pins at the bottom
side of the tuner.
NXP Semiconductors
TD1600ALF-4
Tuner module for digital terrestrial (OFDM) applications
Table 1.
Parameter
Frequency allocation table
TD1611ALF-4/ TD1311ALF-4
174 MHz – 230 MHz
474 MHz – 858 MHz
(*)
TD1344ALF-4
474 MHz – 858 MHz
(*)
RF frequency range
Channel bandwidth
RF-loopthrough range
IF-center frequency
RF input connector
RF output connector
(*)
7/8MHz
ch E2 - ch E69
36.16 MHz
IEC female
IEC male
8 MHz
ch E2 - ch E69
36.16 MHz
IEC female
IEC male
data refer to RF-channel center frequency.
2. Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
TD1600ALF-4
Highly integrated RF-module, 3-band tuner plus active loopthrough
+5V supply voltage only; no external tuning voltage required
Tuners for horizontal and vertical mounting available
Option with DC – power output through input connector (e.g. indoor antenna supply)
Tuners comply with relevant CENELEC standards with regard to requirements
concerning signal handling capability and immunity
Superior low noise and high sensitivity performance
RF-in to RF-out loopthrough amplifiers
Low noise and excellent linearity
Full VHF to UHF frequency range coverage
Standard connectors for in- and output e.g. IEC, F-connector, RCA
High performance and cost effective single conversion tuner
I2C programmable
400kHz Bus compliant
Fast PLL tuning speed (programmable step size e.g. 62.5kHz and 166.67kHz)
Tuner internal gain control loop with selectable TakeOverPoint settings via I2C Bus
External gain control possible with internal loop disabled
4.0V (max. gain) to 0V (min. gain) gain control voltage
Flat overall frequency response
High PLL loop bandwidth which ensures very low oscillator phase noise
4 MHz crystal reference frequency output
SAW-filter and IF-amplifier included
Switchable 7/8 MHz SAW filter
Fixed 8 MHZ SAW filter
IF-amplification controllable over a wide range
© NXP B.V. 2006. All rights reserved.
Preliminary data sheet
Rev.c — 23-04-2007
2 of 27
NXP Semiconductors
TD1600ALF-4
Tuner module for digital terrestrial (OFDM) applications
•
Differential, filtered (SAW) ‘digital’ IF-output to directly drive the channel decoder
3. Ordering information
Table 2.
Ordering information
Table description (optional)
Type number
Package
Name
Description
Version
TD1611ALF/IVP-4
3112 297 15531
VHF 3 – UHF PLL tuner, Loopthrough,
antenna power, Screw hole, DC/DC converter, -
IEC connector, vertical mount
VHF 3 – UHF PLL tuner, Loopthrough,
antenna power, Screw hole, DC/DC converter, -
IEC connector, horizontal mount
VHF 3 – UHF PLL tuner, Loopthrough,
antenna power, DC/DC converter, IEC
connector, vertical mount
VHF 3 – UHF PLL tuner, Loopthrough,
antenna power, DC/DC converter, IEC
connector, horizontal mount
UHF only PLL tuner, loopthrough, antenna
power, Screw hole, DC/DC converter, IEC
connector, vertical mount
UHF only PLL tuner, Loopthrough, antenna
power, Screw hole, DC/DC converter, IEC
connector, horizontal mount
UHF only PLL tuner, Loopthrough, antenna
power, DC/DC converter, IEC connector,
vertical mount
UHF only PLL tuner, Loopthrough, antenna
power, DC/DC converter, IEC connector,
horizontal mount
TD1611ALF/IHP-4
3112 297 15521
TD1311ALF/IVP-4
3112 297 15491
-
TD1311ALF/IHP-4
3112 297 15481
-
TD1644ALF/IVP-4
3112 297 15631
-
TD1644ALF/IHP-4
3112 297 15621
-
TD1344ALF/IVP
-4
3112 297 15511
-
TD1344ALF/IHP-4
3112 297 15501
-
TD1311AF/PHP-4
3112 297 15691
VHF 3 – UHF PLL tuner, antenna power,
DC/DC converter, phono connector, horizontal -
mount
TD1600ALF-4
© NXP B.V. 2006. All rights reserved.
Preliminary data sheet
Rev.c — 23-04-2007
3 of 27
TD1600ALF-4
V
tune
.
33V
PLL
AGC
loop
5V
DC-power for
indoor antenna
AGC
(2)
+5V tuner
supply voltage
( 7)
I C - BUS
(4/5)
2
4MHz
crystal reference
M O P LL
Preliminary data sheet
NXP Semiconductors
4. Block diagram
low-band
low
osc.
AGC
loop
mid-band
mid
Fig 1. Block diagram of TD1616ALF
osc.
high
high-band
RF-input
Rev.c — 23-04-2007
osc.
SAW
RF- output
reference IF - output IF - AGC IF - output
frequency (broadband)
(narrowband)
output
(6)
(8)
(9)
(10/11)
Tuner module for digital terrestrial (OFDM) applications
© NXP B.V. 2006. All rights reserved.
(1)
TD1600ALF-4
4 of 27
NXP Semiconductors
TD1600ALF-4
Tuner module for digital terrestrial (OFDM) applications
5. Pinning information
5.1 Pinning
Fig 2. Pinning diagram
5.2 Pin description
Table 3.
Pin description
Table description (optional)
Pin
1
2
3
4
5
6
7
8
9
10
11
[1]
[2]
[3]
[4]
[5]
Description
DC-power option for tuners with P-extension
[1]
External RF-gain control voltage (0.5V - 4.0V)
PLL chip address select (I
2
C / tuner)
[3]
SCL (I
2
C / tuner)
SDA (I
2
C / tuner)
4MHz reference frequency output
[4]
+5V
±
5% supply tuner (V
TU
)
'broadband' IF – output
[4]
IF-gain control voltage
[5]
'narrowband' IF – output 1
[4]
'narrowband' IF – output 2
[4]
Max. permissible current: 35mA
Max. permissible control voltage source impedance limited to 200ohms (see application notes)
see application notes
AC coupled
max. gain at 3V,min. gain at 0V (see application notes)
[2]
TD1600ALF-4
© NXP B.V. 2006. All rights reserved.
Preliminary data sheet
Rev.c — 23-04-2007
5 of 27
京公网安备 11010802033920号
EEWORLD
