EEWORLDEEWORLDEEWORLD

Part Number

Search

PI2EQX3232B

Description
3.2Gbps, 2-Port, SATAi/m, Serial Re-Driver
File Size457KB,7 Pages
ManufacturerPericom Semiconductor Corporation (Diodes Incorporated)
Websitehttps://www.diodes.com/
Download Datasheet Compare View All

PI2EQX3232B Overview

3.2Gbps, 2-Port, SATAi/m, Serial Re-Driver

PI2EQX3232B
3.2Gbps, 2-Port, SATAi/m, Serial Re-Driver
Features
Supports data rates up to 3.2Gbps on each lane
Adjustable Transmiter De-Emphasis & Amplitude
Adjustable Receiver Equalization
Spectrum Reference Clock Buffer Output
Optimized for SATAi/m applications
Input signal level detection & output squelch on all channels
100-Ohm Differential CML I/O’s
Low Power (100mW per Channel)
Standby Mode – Power Down State
V
DD
Operating Range: 1.8V +/-0.1V
Packaging (Pb-free & Green):48-contact TQFN
Description
Pericom Semiconductor’s PI2EQX3232B is a low power, signal
Re-Driver. The device provides programmable equalization,
amplification, and de-emphasis, to optimize performance over a
variety of physical mediums by reducing Inter-Symbol Interference
(ISI). PI2EQX3232B supports four 100-Ohm Differential CML
data I/O’s between the Protocol ASIC to a switch fabric, across
a backplane, or to extend the signals across other distant data
pathways on the user’s platform.
The integrated equalization circuitry provides
exibility with
signal integrity of the signal before the Re-Driver. Whereas the
integrated de-emphasis circuitry provides
exibility with signal
integrity of the signal after the Re-Driver.
A low-level input signal detection and output squelch function
is provided for all four channels. Each channel operates fully
independantly. When a channel is enabled (EN_x=1) and
operating, that channels input signal level (on xI+/-) determines
whether the output is enabled. If the input level of the channel
falls below the active threshold level (Vth-) then the output driver
switches off, and the pin is pulled to VDD via a high impedance
resistor. If the input level of the channel falls below the active
threshold level (Vth-) then the outputs are driven to the common
mode voltage.
In addition to providing signal re-conditioning, Pericom’s
PI2EQX3232B also provides power management Stand-by mode
operated by an Enable pin.
Block Diagram
Signal Detect
Pin Description
Sel_EQ_A
Sel_EQ_B
Sel_DE_A
Sel_DE_B
Sel_OL_A
Sel_OL_B
EN_C
39
EN_D
38
EN_A
EN_B
VDD
48
47
46
45
44
43
42
41
40
CML
CML
xI+
Equalizer
xI-
SEL_EQ
_x
EN_x
Power
Management
SEL_OL_x
SEL_DE_ x
Limiting
Amp
xO-
xO+
AI+
AI-
VDD
BO
+
BO-
VDD
CI+
CI-
VDD
DO
+
DO-
VDD
1
2
3
4
5
6
7
8
9
10
11
12
36
35
34
33
32
31
37
VDD
AO
+
AO -
VDD
BI+
BI-
VDD
CO
+
CO
-
VDD
DI+
DI-
GND
GND
30
29
28
27
26
25
-- Repeated 4 times --
CKIN-
CKIN+
Buffer
EN_
CLK
13
OUT-
OUT+
14
15
16
17
18
19
20
21
22
23
CKIN-
Sel_EQ_C
Sel_EQ_D
OUT+
Sel_OL_C
Sel_OL_D
Sel_DE_C
EN_CLK
CKIN+
Sel_DE_D
IREF
07-0225
1
OUT
-
PS8889D
IREF
24
10/03/07

PI2EQX3232B Related Products

PI2EQX3232B PI2EQX3232BZDE
Description 3.2Gbps, 2-Port, SATAi/m, Serial Re-Driver 3.2Gbps, 2-Port, SATAi/m, Serial Re-Driver
What is the difference between the principles of switching power supply and DC-DC
Below is the schematic diagram of a DC/DC power supply. The voltage of RL can be controlled by adjusting the pulse width of PWM. If the 220V pulsating DC is adjusted through PWM, can the DC output vol...
bigbat Power technology
MT8888 can correctly send DTMF signals to TEA1062, and TEA1062 also successfully drives DTMF to the telephone line, but the dialing is unsuccessful and there is no prompt tone.
I built a board according to the classic telephone circuit, the schematic diagram is shown below. MT8888 is a DTMF transceiver, and TEA1062 is a telephone voice chip with a dialing interface. The TONE...
中流砥拄 Embedded System
Help with the problem that F2802 cannot be run after being burned
I am using the F2802-60 device. The program I wrote runs well when it is simulated in RAM using the emulator and CCS3.3. However, after changing the flash configuration cmd file, compilation and downl...
dorna Microcontroller MCU
Lock-in amplifier intelligent detection system
[p=22, null, left][color=rgb(60, 60, 60)][font=微软雅黑, Tahoma,]1 Overview[/font][/color][/p][p=22, null, left][color=rgb(60, 60, 60)][font=微软雅黑, Tahoma,] In order to reduce the tedious process of manual...
qwqwqw2088 Analogue and Mixed Signal
Ask a question about spi, urgent!!
Our project is to do an embedded simulation. When I read the SPI manual of s3c2410, I don't understand the following questions. I would be grateful if any expert can give me some advice! ! Here are th...
mcd511786450 Embedded System
The computer is incredibly slow to respond
My computer was shut down several times due to power outages. As a result, it was very slow when I turned it on in the afternoon. It took more than ten minutes to boot up. I couldn't open it with anti...
SONGQY Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2400  1473  1362  1645  1561  49  30  28  34  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号