Over recommended operating conditions unless otherwise stated.
Symbol
R
POT
R
POT
R
POT
R
POT
Parameter
Potentiometer Resistance (-00)
Potentiometer Resistance (-50)
Potentiometer Resistance (-10)
Potentiometer Resistance (-2.5)
Potentiometer Resistance
Tolerance
R
POT
Matching
Power Rating
Wiper Current
Wiper Resistance
Wiper Resistance
Voltage on any R
H
or R
L
Pin
Resolution
Absolute Linearity
(5)
Relative Linearity
(6)
Temperature Coefficient of R
POT
Ratiometric Temp. Coefficient
Potentiometer Capacitances
Frequency Response
Test Conditions
Min
Typ
100
50
10
2.5
±20
25°C, each pot
I
W
= ±3mA @ V
CC
= 3V
I
W
= ±3mA @ V
CC
= 5V
V
SS
= 0V
R
W(n)(actual)
- R
(n)(expected)(8)
R
W(n+1)
- [R
W(n) + LSB
]
(8)
(4)
(4)
(4)
R
POT
= 50kΩ
(4)
±300
20
10/10/25
0.4
1
50
±6
300
150
V
CC
±1
±0.2
Max
Units
kΩ
kΩ
kΩ
kΩ
%
%
mW
mA
Ω
Ω
V
%
LSB
(7)
LSB
(7)
ppm/ºC
ppm/ºC
pF
MHz
Ratings
+2.5 to +6
-40 to +85
Units
V
°C
Ratings
-55 to +125
-65 to +150
-2.0 to +V
CC
+ 2.0
-2.0 to +7.0
1.0
300
±12
Units
ºC
°C
V
V
W
ºC
mA
I
W
R
W
R
W
V
TERM
80
GND
1.6
TC
RPOT
TC
RATIO
C
H
/C
L
/C
W
fc
Notes:
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this
specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.
(2) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20ns. Maximum DC
voltage on output pins is V
CC
+0.5V, which may overshoot to V
CC
+2.0V for periods of less than 20ns.
(3) Latch-up protection is provided for stresses up to 100mA on address and data pins from –1V to V
CC
+1V.
(4) This parameter is tested initially and after a design or process change that affects the parameter.
(5) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a potentiometer.
(6) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentio-
As the title says, negative polarity current signal pulse width: 10~20ns amplitude: about 20uA. To achieve I/V conversion, I plan to use OP643 operational amplifier. The circuit diagram is implemented...
[size=4] Hex 80 is sent as a sync character before each transmission. The device acknowledges with hex 90. The data frame is then sent. Each frame begins with a header byte = hex 80. The other bytes o...
I wrote an algorithm function using LM3S9B96 and downloaded it to the on-chip Flash. The execution time is 35us, which is far from the design goal. How can I put this function into RAM to run? When th...
[align=left]1. The P0 port of 51 single-chip microcomputer is very special. 2. The operation of 51 single-chip microcomputer is essentially the operation of registers, and the same is true for other s...
Many years ago, a developer, seeking a deeper understanding of embedded systems, asked this question: How can I know and understand what my system is doing?
I was a little surprised by this question b...
Designing for automotive LCD displays larger than 5" can be complex. The display source driver requires a supply rail called analog voltage device drain (AVDD) in the 10V to 15V range and two supply ...[Details]
In order to strengthen the management of new energy vehicle charging facilities in our city, prevent and reduce accidents, protect the lives and property of the people, and improve the public safet...[Details]
I have always wanted to write some posts and blogs, but I just couldn't bear to do it as I just graduated. After some preparation, I decided to write down some of the things I learned in the past few...[Details]
Development Background: 1. Main chip - STM32F207VCT6; 2. TCP/IP protocol stack - LWIP, transplanted based on ST routines; 3. Operating system - none (bare metal); Anomalies: 1. Power on the device wi...[Details]
Time flies. Since the beginning of 2018, news related to home appliance companies have repeatedly made headlines, and competition in the home appliance market continues to intensify. In order to be...[Details]
As many companies listed with
the concept of
touch screen
begin to "transform and upgrade", the official voice of the TP industry is getting smaller and smaller. At the same time, the list o...[Details]
With the implementation of the first version of the NR sub-6GHz draft of 3GPP in December 2017, and the subsequent Phase 2 drafts, semiconductor manufacturers and terminal manufacturers began to ...[Details]
As the brain of a mobile phone, the mobile phone processing chip is of great importance. Xiaomi, which started out as the MIUI company, has long been keenly aware of the gap between China and devel...[Details]
When Amazon quietly launched a product called Elastic Computing Cloud 12 years ago, the Internet industry in China, across the ocean, also ushered in an unprecedented development opportunity. Let's...[Details]
In recent years, in addition to Huawei Kirin
chips
in the mobile phone industry
, Xiaomi's own processor Pengpai S1, AI
chip
start-ups such as Cambrian, Horizon, and Deephi Technolo...[Details]
I used the bit definition in my 51 program: bit flag. After defining it this way, I ran the program and downloaded it to the circuit board. I found that the flag was not the value I set, which led to...[Details]
ADC Introduction: ADC (Analog-to-Digital Converter). That is, converting analog signals into digital signals for processing. When storing or transmitting, analog-to-digital converters are almost ...[Details]
The Vatican Secret Archives is one of the world's greatest historical collections, but many of its documents have never been transcribed. Recently, a project called Codice Ratio used a
combination...[Details]
When STM32 uses JTMS (PA13) and JTCK (PA14) as normal I/O ports, add the following code before initialization (the order cannot be reversed): RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE); G...[Details]
Interrupts and timers implement a 24-hour clock. The program is as follows: #include reg52.h #define PORTLEN P0 sbit bit_select = P2^0; sbit seg_select = P2^1; unsigned char src = {0x3f,0x06,0...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
