EEWORLDEEWORLDEEWORLD

Part Number

Search

MIC2211-2.8/2.8BML

Description
IC,VOLT REGULATOR,FIXED,DUAL +2.8V,CMOS,LLCC,10PIN,PLASTIC
CategoryPower/power management    The power supply circuit   
File Size757KB,10 Pages
ManufacturerMicrochip
Websitehttps://www.microchip.com
Download Datasheet Parametric View All

MIC2211-2.8/2.8BML Overview

IC,VOLT REGULATOR,FIXED,DUAL +2.8V,CMOS,LLCC,10PIN,PLASTIC

MIC2211-2.8/2.8BML Parametric

Parameter NameAttribute value
package instructionSON, SOLCC10,.11,20
Reach Compliance Codecompli
AdjustabilityFIXED
Nominal dropback voltage 10.24 V
Maximum absolute input voltage7 V
JESD-30 codeR-PDSO-N10
Maximum grid adjustment rate0.0286%
Output times2
Number of terminals10
Maximum output current 10.15 A
Nominal output voltage 12.8 V
Nominal output voltage 22.8 V
Package body materialPLASTIC/EPOXY
encapsulated codeSON
Encapsulate equivalent codeSOLCC10,.11,20
Package shapeRECTANGULAR
Package formSMALL OUTLINE
Certification statusNot Qualified
surface mountYES
technologyCMOS
Terminal formNO LEAD
Terminal pitch0.5 mm
Terminal locationDUAL
Maximum voltage tolerance2%
Base Number Matches1
MIC2211
Micrel, Inc.
MIC2211
Dual
µCap
LDO in 3mm
×
3mm MLF™
General Description
The MIC2211 is a dual
µCap
low dropout regulator. The first
regulator is capable of sourcing 150mA, while the second
regulator can source up to 300mA.
Ideal for battery operated applications, the MIC2211 offers 1%
accuracy, extremely low dropout voltage (80mV @ 100mA),
and extremely low ground current (only 48µA total). Equipped
with TTL logic compatible enable pins, the MIC2211 can be
put into a zero-off-mode current state, drawing no current
when disabled. Separate enable pins allow individual control
of each output voltage.
The MIC2211 is a
µCap
design, operating with very small
ceramic output capacitors for stability, reducing required
board space and component cost.
The MIC2211 is available in fixed output voltages in the
10-pin 3mm
×
3mm MLF™ leadless package.
Features
• Input voltage range: 2.25V to 5.5V
• Stable with ceramic output capacitor
• 2 LDO outputs:
• Output 1 - 150mA output current
• Output 2 - 300mA output current
• Low dropout voltage of 80mV @ 100mA
Ultra-low quiescent current of 48µA total (24µA/LDO)
• High output accuracy:
• +1.0% initial accuracy
• +2.0% over temperature
• Thermal shutdown protection
• Current limit protection
Tiny 10-pin 3mm
×
3mm MLF™ package
Applications
• Cellular phones
• Wireless modems
• PDAs
Typical Application
MIC2211-xxBML
VIN
OFF ON
VOUT1
VOUT2
1 F
Ceramic
1 F
V
I/O
V
CORE
Baseband
Processor
EN1
EN2
CBYP
OFF ON
0.01 F
GND
MIC2211 Typical Cell Phone Application
MicroLeadFrame
and MLF are trademarks of Amkor Technology, Inc.
Micrel, Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
October 2005
1
M9999-101805
Prize-winning survey | Keysight Technologies’ entry-level R&D oscilloscope EXR is now online with a surprise!
Before introducing the newly released entry-level RD oscilloscope EXR from Keysight Technologies, Please allow me to introduce how to participate in this prize-winning survey~ [bowing]!Scan the QR cod...
EEWORLD社区 Test/Measurement
Help, how to connect FPGA-to-SDRAM to qsys, and how to read and write data to FPGA.
First, let me talk about my ideas. If I say something wrong, I hope you can help correct it: 1. Reserve a space in the DDR of the hps end, specifically set uboot bootargs mem=512M. 2. Then the fpga re...
tc317891209 FPGA/CPLD
Regarding the problem of sources.cmn and sources, please help me, thank you!
Hello everyone, may I ask: 1. What is the difference between sources.cmn and sources? 2. What do these environment variables in sources.cmn represent? ? ? I hope everyone can give a comment! ! ! ! ! T...
xiaoyevinne Embedded System
Question: How to access arm7 IO port?
I'm currently using LPC2220, a Philips model. There are 4 GPIO ports, P0 to P3. How do I access the P3 port? For example, how do I set pin P3.27 to 0 or 1?...
painache ARM Technology
Delay according to the timer value
Given that TH2 and TL2 are the timing values for a workpiece to rotate one circle, and I want to sample 128 points equidistantly on the workpiece, then the interval between two sampling points is obta...
lzj000008 Embedded System
In the driver loader, after StartService(), GetLastError() returns 3 errors (〖3〗-The system cannot find the specified path.)
In the driver loader, [color=#FF0000] after StartService(), GetLastError() returns 3 (〖3〗-The system cannot find the specified path.) [/color][b][/b] When running in a virtual machine, it is fine at t...
0211liucheng Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2005  2607  1897  1720  321  41  53  39  35  7 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号