EEWORLDEEWORLDEEWORLD

Part Number

Search

RBTVSS9EBS

Description
Power/Signal Relay, Momentary, 0.02A (Coil), 9VDC (Coil), 180mW (Coil), 1A (Contact), 28VDC (Contact), DC Input, DC Output, Through Hole-Straight Mount,
CategoryMechanical and electronic products    relay   
File Size518KB,5 Pages
ManufacturerFirst Switchtech
Download Datasheet Parametric View All

RBTVSS9EBS Overview

Power/Signal Relay, Momentary, 0.02A (Coil), 9VDC (Coil), 180mW (Coil), 1A (Contact), 28VDC (Contact), DC Input, DC Output, Through Hole-Straight Mount,

RBTVSS9EBS Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
body height9.5 mm
Body length or diameter8.5 mm
Maximum coil current (DC)0.02 A
Coil power180 mW
Coil resistance400 Ω
Maximum coil voltage (DC)9 V
Coil/Input Power TypeDC
Maximum contact current (DC)1 A
Contact (DC) maximum rated R load1A@28VDC
Maximum contact voltage (DC)28 V
Contact/Output Power TypeDC
Electrical life10000 Cycle(s)
JESD-609 codee3
Installation featuresTHROUGH HOLE-STRAIGHT MOUNT
operating hours5.5 ms
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
GuidelineCECC; MIL-R-39016/11, MIL-R-39016/16, MIL-R-39016/21
Relay actionMOMENTARY
Relay typePOWER/SIGNAL RELAY
release time9 ms
surface mountNO
Terminal surfaceTIN
Termination typeSOLDER
Base Number Matches1
Series TV
Sensitive ultraminiature
«TO 5 transistor size»
non latching relays
28 V / 1 A pick-up power
<
60 mW
APPLICATION SPECIFICATIONS
MIL-R-39016/11 -/16 -/21
CECC 1601-016
General characteristics
N° of pole
Volume
Mass
2 Pdt
0,54 cm
3
2,7 g with leads 38 mm[1.500] lenght
2,3 g with leads 4,75 mm[.187] lenght
2,7 g with spreader pad, leads 4,75 mm[.187] lenght
Switching characteristics
Life at rated load
Nominal contact rating on power supply 28 V d c
1 x 10
5
operations mini
1 A resistive load
0,2 A inductive load (inductance 320 mH)
Lamp: 0,10 A at 28 Vdc
4 ms max
2 ms max
7,5 ms max
1,5 ms max
2 Amperes
Operating time at 25° C
Release time at 25° C T
TV S - TV SS
Bounce time at 25° C
Overload (100 cycles )
Environmental characteristics
Temperature range
Vibration
Shock
Opening contact maxi
Leak rate
- 65° C to + 125° C
30 g 3 000 Hz
75 g 6 ms
10 µs
1 x 10
- 8
atm . cm
3
/ s
Electrical characteristics
Contact resistance ( measured at 3,2 mm from the header)
- Initial
- After life
Dielectric strength (see level)
Between contacts and case
Between coil and case
Between open contact
Between terminals at 22 000 m altitude
Insulation resistance
(at 20°C, 50% relative humidity)
Coil / case at 125 °C
Coil data
0,10
max
0,20
max
500
500
500
125
V
V
V
V
Relay with spreader pad
0,12
max
0,22
max
rms
rms
rms
rms
> 10 000 M
at 500 V dc
> 1 000 M
see page 4
22, rue des Chaises
45 140 SAINT JEAN DE LA RUELLE - FRANCE
www.stpigroup.com
Tél : +33 (0)2 38 70 45 00
series TV
page 1 / 5
Conversion between different versions of iar
Maybe when we used the lower versions IAR4.41 IAR4.42 to do a lot of work and a lot of projects, but with the update of simulation tools, the old versions can no longer inherit the new simulation tool...
m200200 stm32/stm8
How to disable all interrupts in STM32 processor
I have never found the function of all interrupts in STM32. I want to ask if it is impossible to implement it. Or is there any way to implement this function? It is very troublesome to turn off each o...
aphonline stm32/stm8
MSP430 (F149) study notes - infrared reception
Using MSP430 (F149) to receive infrared is simpler than sending. The infrared sensor I use is HS0038B. This component outputs a low level when receiving 38K infrared, otherwise it outputs a high level...
girlkoo Microcontroller MCU
Confusion about device models
Many data sheets describe a series, such as the msp430X1XX series. After reading them, you may find problems in the process of using them. For example, the msp430F149 series data sheet says that it ha...
zhangdaoyu Microcontroller MCU
How to adjust the COM port number if it is too large?
I am using BSL downloader to connect to the computer and it is displayed as COM12, but in the BSL download software there is a serial port selection with the highest being COM8, what should I do :Sad:...
王一天 Microcontroller MCU
atmega32 read and write sd card problem, please guide
I have just started learning AVR and my level is limited. Now I want to use the SPI mode of Atmega32 to read and write SD cards. At present, I am doing simple reading and writing without adding a file...
vsunl Microchip MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2330  2557  1250  1155  1310  47  52  26  24  27 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号