MV64V2CD1.500MHZ datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> MV64V2CD1.500MHZ

MV64V2CD1.500MHZ: DescriptionOscillator, 1.5MHz Min, 155.52MHz Max, 1.5MHz Nom; CategoryPassive components oscillator; File Size59KB，1 Pages; ManufacturerMtronPTI; Websitehttp://www.mtronpti.com

Download Datasheet Parametric View All

MV64V2CD1.500MHZ Overview

Oscillator, 1.5MHz Min, 155.52MHz Max, 1.5MHz Nom

MV64V2CD1.500MHZ Parametric

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
package instruction	DIP4/14,.3
Reach Compliance Code	unknown
Installation features	THROUGH HOLE MOUNT
Number of terminals	4
Maximum operating frequency	155.52 MHz
Minimum operating frequency	1.5 MHz
Nominal operating frequency	1.5 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Package body material	METAL
Encapsulate equivalent code	DIP4/14,.3
power supply	5 V
Certification status	Not Qualified
Maximum slew rate	35 mA
Nominal supply voltage	5 V
surface mount	NO
Base Number Matches	1

Preview

Download Datasheet

View All

MV Series

14 DIP, 5.0 Volt, HCMOS/TTL, VCXO

•

General purpose VCXO for Phase

Lock Loops (PLL), Clock Recovery,

Reference Signal Tracking and

Synthesizers

•

Frequencies up to 160 MHz and tri-

state option

*Contact factory for availability.

Pin Connections

Frequencies above 90 MHz utilize a PLL design. Fundamental and PLL designs are available for other frequencies. Contact factory.

TTL load - see load circuit diagram #1 on page 148. HCMOS load - see load circuit diagram #2 on page 148.

Symmetry is measured at 1.4 V with TTL load, and at 50% with HCMOS load.

Rise/Fall times are measured between 0.5 V and 2.4 V for TTL load, and between 10% Vdd and 90% Vdd for HCMOS load.

MtronPTI reserves the right to make changes to the product(s) and service(s) described herein without notice. No liability is assumed as a result of their use or application.

Please see

www.mtronpti.com

for our complete offering and detailed datasheets. Contact us for your application specific requirements: MtronPTI

1-800-762-8800.

Recommended Resources

Single-phase electric water pump water level control point card

Dual op amp three-stage tone processing circuit diagram

Wireless microphone circuit

Shengfeng DNL-L80A automatic rotating quartz electric heater circuit diagram

Fish tank oxygenation timer circuit

High input-high output voltage integrated regulated power supply circuit 3

Why can't I download the debugger directly to NANDFLASH under VS2005+CE60 (EVC+CE50 can)? Must I add a prefix like CSIDL_XXX? How to add NANDFLASH: Why can't I download the debugger directly to NANDFLASH under VS2005+CE60 (EVC+CE50 can)? Must I add a prefix like CSIDL_XXX? NANDFLASH still doesn't work even if I add a prefix like this?...; torresgerrard Embedded System

Ask, precision rectifier circuit problem: I would like to ask you all, the output of my precision rectifier circuit is asymmetrical. When the input is 1V, the output is about 1.5V, and when the input is 2V, the output is about 2.5V. When the ...; danielpeng Analog electronics

Debugging issues with Simple socket server routines: I'm using the Cyclone III FPGA Development Kit to debug the Simple Socket Sever example, but it has been several days since I've been able to debug it. The network cable is fine, the IP settings are f...; eeleader FPGA/CPLD

How to crack the code limit of CW5.0-CW5.2 XGATE: [backcolor=rgb(239, 245, 249)]As the title says[/backcolor] [backcolor=rgb(239, 245, 249)]Use cw5.2 to develop s12x series MCU, but the amount of code in xgate is limited, and only supports 512 bytes ...; xinjitmzy NXP MCU

[Surprising Gift] Participate in the WEBENCH Design Competition and experience the true meaning of design easily!: [b][color=#ff0000]Activity Name: [/color][/b][font=微软雅黑][color=#000000]Participate in the WEBENCH Design Contest and easily experience the true meaning of design with a surprise gift! [/color][/font] ...; EEWORLD社区 Analogue and Mixed Signal

Tip: The macro prompt of .h is not defined: The .h file is included in .c, but the prompt says that the macro defined in .h is not defined, but .c includes the .h file; .c uses the macro of .h; but the prompt says that the macro is not defined....; liuhuaqiang1118 NXP MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components