CAT5113Y-50 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> converter> CAT5113Y-50

CAT5113Y-50: DescriptionDigital Potentiometer, 1 Func, 50000ohm, Increment/decrement Control Interface, 100 Positions, CMOS, PDSO8, LEAD FREE AND HALOGEN FREE, TSSOP-8; CategoryAnalog mixed-signal IC converter; File Size451KB，9 Pages; ManufacturerCatalyst; Websitehttp://www.catalyst-semiconductor.com/; Environmental Compliance

Download Datasheet Parametric View All

CAT5113Y-50 Overview

Digital Potentiometer, 1 Func, 50000ohm, Increment/decrement Control Interface, 100 Positions, CMOS, PDSO8, LEAD FREE AND HALOGEN FREE, TSSOP-8

CAT5113Y-50 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Parts packaging code	SOIC
package instruction	TSSOP, TSSOP8,.25
Contacts	8
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	NONVOLATILE MEMORY
control interface	INCREMENT/DECREMENT
Converter type	DIGITAL POTENTIOMETER
JESD-30 code	R-PDSO-G8
JESD-609 code	e3
length	4.4 mm
Humidity sensitivity level	1
Number of functions	1
Number of positions	100
Number of terminals	8
Maximum operating temperature	70 °C
Minimum operating temperature
Package body material	PLASTIC/EPOXY
encapsulated code	TSSOP
Encapsulate equivalent code	TSSOP8,.25
Package shape	RECTANGULAR
Package form	SMALL OUTLINE, THIN PROFILE, SHRINK PITCH
Peak Reflow Temperature (Celsius)	260
power supply	3/5 V
Certification status	Not Qualified
resistance law	LINEAR
Maximum resistor tolerance	20%
Maximum resistor terminal voltage	3 V
Minimum resistor terminal voltage
Maximum seat height	1.2 mm
Nominal supply voltage	3 V
surface mount	YES
technology	CMOS
Nominal temperature coefficient	300 ppm/°C
Temperature level	COMMERCIAL
Terminal surface	MATTE TIN
Terminal form	GULL WING
Terminal pitch	0.65 mm
Terminal location	DUAL
Maximum time at peak reflow temperature	40
Nominal total resistance	50000 Ω
width	3 mm
Base Number Matches	1

Preview

Download Datasheet

View All

CAT5113

100-Tap Digitally Programmable Potentiometer (DPP™)

FEATURES

100-position linear taper potentiometer

Non-volatile EEPROM wiper storage

10nA ultra-low standby current

Single supply operation: 2.5V-6.0V

Increment Up/Down serial interface

Resistance values: 1kΩ ,10kΩ , 50kΩ and 100kΩ

Ω

Available in PDIP, SOIC, TSSOP and MSOP packages

GEN

ALO

APPLICATIONS

Automated product calibration

Remote control adjustments

Offset, gain and zero control

Tamper-proof calibrations

Contrast, brightness and volume controls

Motor controls and feedback systems

Programmable analog functions

DESCRIPTION

The CAT5113 is a single digitally programmable

potentiometer (DPP™) designed as a electronic

replacement for mechanical potentiometers and trim

pots. Ideal for automated adjustments on high volume

production lines, they are also well suited for

applications where equipment requiring periodic

adjustment is either difficult to access or located in a

hazardous or remote environment.

The CAT5113 contains a 100-tap series resistor array

connected between two terminals R

and R

. An up/

down counter and decoder that are controlled by three

input pins, determines which tap is connected to the

wiper, R

. The wiper setting, stored in nonvolatile

memory, is not lost when the device is powered

down and is automatically reinstated when power

is returned. The wiper can be adjusted to test

new system values without effecting the stored

setting. Wiper-control of the CAT5113 is

accomplished with three input control pins,

CS,

U/D,

and

INC.

The

INC

input increments the wiper in the

direction which is determined by the logic state of

the U/D input. The

input is used to select the

device and also store the wiper position prior to

power down.

The digitally programmable potentiometer can be

used as a three-terminal resistive divider or as a

two-terminal variable resistor. DPPs bring variability and

programmability to a wide variety of applications

including control, parameter adjustments, and

signal processing.

FUNCTIONAL DIAGRAM

Vcc

(Supply Voltage)

U/D

INC

7-BIT

UP/DOWN

COUNTER

/ V

7-BIT

NONVOLATILE

MEMORY

ONE

ONE HUNDRED

DECODER

UP/DOWN

(U/D)

INCREMENT

(INC)

DEVICE SELECT

(CS)

POR

Control

and

Memory

/ V

TRANSFER

GATES

RESISTOR

ARRAY

/ R

/ V

Vcc

STORE AND

RECALL

CONTROL

CIRCUITRY

GND

GENERAL

/ V

/ R

GENERAL

DETAILED

ELECTRONIC POTENTIOMETER

IMPLEMENTATION

Characteristics subject to change without notice

Doc. No. 2009, Rev. R

Recommended Resources

TA8200AH power amplifier circuit drawing schematic diagram

Phone in use indicator light circuit

555 contactless timing circuit

Potentiometer pressure sensor two-wire transmission circuit

Amplified exposurer circuit

Push-pull switching regulated power supply circuit composed of CW1524

ucOS-II transplantation: I have compiled the uCOS-II porting source code, mainly including the porting source code for 51, AVR, LPC, Freescale and Fustu models! I hope it will be helpful to everyone...; wstrom Real-time operating system RTOS

Some experience and routines of using MSP430FR2000: Some time ago, I came into contact with the MSP430FR2000 microcontroller for a project. Because I used the MSP430F5529 most of the time before, it was relatively simple to get started with this microc...; yg776 Microcontroller MCU

Wavecom sends Chinese text messages with errors: I refer to many examples on the Internet, my steps are as follows: 1.at+enter //return OK 2.at+csca=13800240500 +enter //return OK (SMS service center in Shenyang area) 3.at+cmgf=0 +enter //return OK ...; 大漠孤烟 Embedded System

Reasons why the IAR simulation 430 timer does not interrupt: I would like to ask you, I am now using IAR to simulate MSP430F135. The soft simulation cannot generate interrupts, but the hard simulation can. However, the interrupt is entered again as soon as it r...; tangwenwenit Microcontroller MCU

#Meet friends by disassembling# Disassembling a HITECH HMI: [size=4]I have two industrial HMIs, one of which is a HMI from HITECH, model PWS6500S-S. See the appearance and parameters in the figure below (from Baidu)[/size] [size=4][/size] [size=4] [/size] [siz...; wo4fisher Making friends through disassembly

How to combine hot-swap and e-fuses: [align=left][color=#000]When designing a power supply, the question of protection often arises. How much protection do you need? How do you implement it? If you are still using fuses for protection, c...; maylove Analogue and Mixed Signal

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components