EEWORLDEEWORLDEEWORLD

Part Number

Search

TM201-D23

Description
150- 200 WATT MEDICAL POWER SUPPLIES
File Size327KB,3 Pages
ManufacturerTRUMPower
Websitehttp://www.trumpower.com/
Download Datasheet View All

TM201-D23 Overview

150- 200 WATT MEDICAL POWER SUPPLIES

TRUMPower
D E SCR IPTION
150- 200 WATT MEDICAL POWER SUPPLIES
TM201 SERIES
( LV D )
The TM201 series comprising single and multiple
output models for 150 to 200 watts of continuous
output power is specially designed for dental and
medical applications. They operate at 90 to
264VAC input voltage without the need of a
selector strap. All auxiliary outputs are with
magnetic amplifier linear regulator to keep
regulation. The units are constructed on a printed
circuit board with a U-bracket for mechanical
support and heat sinking. A cover-and-fan
assembly can be added during manufacturing.
RoHS
F EATU R E S
Low safety ground leakage current
M e e t E N 5 5 0 11 a n d F C C C l a s s B
Pow er Factor 0.98 typical
Short-circuit protection
Pow er Fail Detect
PFD
signal
100% burn-in at full rated load
Optional cover-and-fan assembly
Remote inhibit - TTL high disables output
C o m p l i a n t w i t h R o H S r e q u i r e m e n ts
Saf et y Sta n da rd A ppr o va ls:
UL 60601-1
CSA C22.2 No. 601.1
TÜV EN60601-1
ENVIRONMENTAL SPECIFICATIONS
IN PUT S PE C IF ICAT ION S
9 0 t o 2 6 4 VA C
47 to 63Hz
3 . 2 A
r m s
f o r 11 5 VA C
1 . 6 A
r m s
f o r 2 3 0 VA C
E a r t h l e a k a g e c u r r e n t
9 0 µ A m a x . @ 11 5 VA C , 6 0 H z
1 5 0 µ A m a x . @ 2 3 0 VA C , 5 0 H z
I n p u t v o l ta g e
Input frequency
Input current
Operating temperature:
Storage temperature:
Relative humidity:
Derating:
Cooling:
0ºC to +70ºC
-40ºC to +85ºC
5% to 95% non-condensing
Derate from 100% at +50ºC
linearly to 50% at +70ºC
10.8 CFM forced air provided on “C”
version; 25 CFM forced air to be
provided for U-bracket version by
user.
OUTPUT SPECIFICATIONS
Output voltage/current:
Total output power:
Ripple and noise:
Overvoltage protection:
See rating chart
200 watts maximum
2% peak to peak maximum
Provided on output #1 only;
set at 112-132% of its nominal
output voltage
All outputs protected to short
circuit conditions
All outputs ±0.04/ºC maximum
Maximum excursion of 4% or
better on all models,
recovering to 1% of final
value within 500µs after a
25% step load change
TTL logic high for normal
operation and TTL logic low
upon loss of input power. This
signal appears at least 1ms
prior to +5V output dropping
5% below its nominal value.
This signal also provides a
minimum delay of 100ms after
+5V is within regulation.
GENERAL SPECIFICATIONS
Switching frequency:
Efficiency:
Hold-up time:
Line regulation:
Inrush current:
Withstand voltage:
88 KHz –112 KHz
70% minimum on all models
20 msec minimum at 110VAC
±0.5% maximum at full load
20 amps @ 115VAC or 40 amps
@ 230VAC, at 25ºC cold start
Overcurrent protection:
Temperature coefficient:
Transient response:
PFD signal:
4000VAC from input to output
1500VAC from input to ground
500VAC from output to ground
MTBF:
350,000 hours at full load at
25ºC ambient, calculated per
MIL-HDBK-217F
EMC Performance (EN60601-1-2: 2001)
E N 5 5 0 11 :
Class B conducted, Class B
radiated
EN61000-3-2:
Harmonic distortion, Class A and D
EN61000-3-3:
Line flicker
EN61000-4-2:
ESD, ±8KV air and ±6KV contact
EN61000-4-3:
Radiated immunity, 3V/m
EN61000-4-4:
Fast transient/burst, ±2KV
EN61000-4-5:
Surge, ±1KV diff, ±2KV com.
EN61000-4-6:
Conducted immunity, 3Vrms
EN61000-4-8:
Magnetic field immunity, 3A/m
E N 6 1 0 0 0 - 4 - 11 :
Voltage dips, 30% reduction for
500ms, 60% reduction for 100ms
and >95% reduction for 10ms
Tumbler Technologies + TRUMPower
3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA
Phone: 408-988-6616
Fax: 408-988-6622
email: sales@trumpower.com
Website: www.TRUMPower.com
Stray test line loss problem?
[color=#333333]Is there a problem with the line loss in stray test? Sometimes the measured value is a range, how to determine the line loss? [/color]...
gurou1 RF/Wirelessly
IO simulates serial port, the program runs a little unstable, I hope the expert can give me some advice
/***************************************************Program function: IO port simulates serial port. The clock is 30K and the baud rate is 9600.Sometimes it works stably, and sometimes it's all garble...
hider Microcontroller MCU
I would like to ask about the resistance of dynamic display.
I am not very good at this, so I can only draw some intuitive pictures to illustrate the problem. The following picture is my understanding. The current flows from +5V to P0 port. How big should the c...
zxpla MCU
Ten Golden Rules of PCB Design
[align=left] Despite the increasing integration of semiconductors, the availability of readily available systems-on-chips for many applications, and the increasing availability of powerful, ready-to-u...
ohahaha PCB Design
Students and experts who are familiar with BeagleBone please come in
I have a beaglebone blue. After I got it, I read a tutorial and updated the system. Then I couldn't open the cloud9 ide on the web. I couldn't connect to the address 192.168.7.2:3000. How can I solve ...
lidingding Embedded System
Fujitsu FRAM Experience Submission
The samples were received on Monday, 5 PCS in total, model number MB85RC256VPF-G-JNERE2. Now I have made a board and added FRAM to the circuit board. It will be back this week. I will compile the prog...
youzizhile Integrated technical exchanges

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2106  917  986  2405  2052  43  19  20  49  42 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号