BCW896-0670-30AB95 datasheet, PDF

Datasheet> All Categories > The connector> socket> BCW896-0670-30AB95

BCW896-0670-30AB95: DescriptionIC Socket, BGA896, 896 Contact(s), ROHS COMPLIANT; CategoryThe connector socket; File Size1MB，8 Pages; ManufacturerActel; Websitehttp://www.actel.com/; Environmental Compliance

Download Datasheet Parametric View All

BCW896-0670-30AB95 Overview

IC Socket, BGA896, 896 Contact(s), ROHS COMPLIANT

BCW896-0670-30AB95 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	Actel
package instruction	ROHS COMPLIANT
Reach Compliance Code	compliant
Contact to complete cooperation	GOLD/TIN
Contact completed and terminated	GOLD/TIN
Contact material	BERYLLIUM COPPER
Device slot type	IC SOCKET
Type of equipment used	BGA896
Shell material	CERAMIC
JESD-609 code	e4/e3
Manufacturer's serial number	BCW
Number of contacts	896
Base Number Matches	1

Preview

Download Datasheet

View All

Socket Mounting Recommendations and Reflow Profile

Purpose

This document is meant to serve as a guide for mounting E-tec surface mount device (SMD)

sockets to the printed circuit board (PCB). The recommendations described here are guidelines

only, and modifications may be needed for your particular socket, PCB, and process.

Application

The sockets this document applies to are as follows: Clam Shell, Knob Lock, Screw Lock, Twist

Lock, Quick Lock and Lever Lock in SMD style. These sockets utilize the E-tec patented spring-

pin technology. This technology allows the pins to be soldered to the PCB while still providing

compliance to the device under test (DUT) via springs located at the other end of the pin. The

pins themselves do not have solder pre-forms as a BGA would with its solder balls. However, the

sockets are designed to mount to the same PCB footprint and pads as required by the BGA, or

any other IC package the socket was designed for (except if locating pegs are used; see ‘Locating

Pegs’ section of this document). When compared to mounting a BGA, an extra volume of solder

paste is required to mount the sockets to the PCB. To effect this, a properly dimensioned stencil

is required. Once the paste has been applied, a standard reflow process is then used to solder the

socket to the PCB. After the socket is verified to have proper electrical connection to the PCB,

the system is then ready to be used.

Locating Pegs

Although designed to mount to the same footprint as the IC, with just a small amount of

additional keep-out area, E-tec sockets can also be offered with locating pegs. The sockets are

typically mounted with two locating pegs, which require two thru-holes drilled into the PCB.

These pegs help to align the socket on the PCB, and hence align the socket’s pins to the PCB’s

pads, during the soldering process. Furthermore, plating the thru-holes allows the locating pegs

to be soldered to the PCB for better mechanical stability during everyday use and handling of the

socket. If the PCB design permits, E-tec recommends the use of these locating pegs. For fine-

pitch, low pin-count sockets without locating pegs, the mechanical strength of the solder joints

may be insufficient. In these cases, it is recommended to epoxy the socket body to the PCB. 3M

Scotch-Weld 2216 B/A is a suitable epoxy. In any case, the proper volume of solder paste is

required to ensure mechanical and electrical integrity. Recommended stencil dimensions are

given in the next section of this document.

E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland

Phone +41-21-781 08 10 ·

www.e-tec.com

info@e-tec.com

E-tec Socket Mounting Recommendations

PRELIMINARY

Recommended Resources

Using 8255 port to form matrix keyboard circuit

Relationship diagram of the main components of DC brush motor

tristable circuit

555 warehouse temperature measurement and alarm circuit

Computer motherboard circuit diagram 815 2_25

I drew a circuit diagram. Please take a look to see if there is anything wrong. Thank you.: This is the first time I draw the preamplifier circuit and the reverse amplifier circuit. Please give me more advice, especially on impedance matching. Thank you....; 黏三皮黏三皮 PCB Design

About the experience of using STM32F301: Recently, I needed an MCU that can realize dynamic adjustment of op amps, with comparators and 32-bit timers. I finally found STM32F301 through ST-MCU-FINDER. This chip is very cheap on Taobao, and yo...; cxzs1234 stm32/stm8

LCD screen, RS232/RS422 converter, Ethernet to RS232/RS485/RS422 module: [i=s]This post was last edited by zhoupxa on 2013-12-26 18:44[/i] 1. 8 disassembled TRULY brand 12864 dot matrix LCD screens, model MCG12864C2-3, with negative pressure and backlight, specification an...; zhoupxa Buy&Sell

A TI friend's suggestion for your reference~~~: You can consider using TI's UCD3028 series digital power supply. UCD3028 has a complete solution, and it will be easier to develop based on the solution. The UCD3K series is an isolated power supply s...; soso DIY/Open Source Hardware

Accurate Fuel Gauge for All Portable Electronic Devices: [align=left]Have you ever had this experience: every time before going out, you have to check the battery level of your phone, fearing that the battery level is not enough to support a day's use? Or w...; 德州仪器_视频 Analogue and Mixed Signal

High-Speed PCB Design Guidelines: High-speed PCB design guide, a total of eight chapters, word document, worth reading...; ybbfn PCB Design

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components