EEWORLDEEWORLDEEWORLD

Part Number

Search

142-0593-401

Description
CONNECTOR, PANEL MOUNT, CABLE TERMINATED, FEMALE, SMA CONNECTOR, SOLDER, JACK
CategoryThe connector    The connector   
File Size935KB,3 Pages
ManufacturerArtysen Embedded Technologies
Download Datasheet Parametric Compare View All

142-0593-401 Online Shopping

Suppliers Part Number Price MOQ In stock  
142-0593-401 - - View Buy Now

142-0593-401 Overview

CONNECTOR, PANEL MOUNT, CABLE TERMINATED, FEMALE, SMA CONNECTOR, SOLDER, JACK

142-0593-401 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresINSERTION LOSS MAX AT 10GHZ
Body/casing typeJACK
Characteristic impedance50 Ω
Connector typeRF SMA CONNECTOR
Contact to complete cooperationGOLD (30)
Contact completed and terminatedGOLD (30)
Contact point genderFEMALE
Coupling typeTHREADED
DIN complianceNO
Filter functionNO
IEC complianceNO
Insertion loss0.09 dB
insulator materialPTFE FLUOROCARBON/PFA
JESD-609 codee4
MIL complianceNO
Manufacturer's serial numberSMA
Installation methodSTRAIGHT
Installation typeCABLE
Maximum operating frequency26.5 GHz
OptionsGENERAL PURPOSE
Panel mountingYES
Termination typeSOLDER
voltage standing wave ratio1.35
Base Number Matches1
SMA 50 Ohm
Straight Solder Type Bulkhead Jack
INCHES (MILLIMETERS)
CUSTOMER DRAWINGS AVAILABLE UPON REQUEST
CABLE TYPE
.086
Semi-Rigid
VSWR & FREQ. RANGE
0-18 GHz:
1.07 + .008 f (GHz)
26.5 GHz: 1.35 Max
GOLD PLATED NICKEL PLATED
142-0593-401
142-0593-406
Mounting hole layout
CABLE GROUP
RG-405/u
(.086 semi-rigid)
PART NUMBER
142-0593-401/406
“A”
.070 (1.78)
1.
Identify connector parts. (2 piece parts)
2.
Strip cable to dimensions shown. Do not nick
center conductor.
3.
Place center contact on center conductor
making sure contact bottoms against cable
insulation. Solder center conductor to center
contact through solder hole. Solder
must
not
be allowed to run on outside of contact.
Use a minimum amount of solder for a good
joint.
.020 (0.51) diameter solder is
recommended.
Trim excess insulation.
4.
Insert contact and cable into body assembly
making sure cable is bottomed against
insulator in body. Solder body to cable. Use
a minimum amount of heat to minimize cable
insulation movement.
Emerson Network Power Connectivity Solutions
299 Johnson Avenue SW, Waseca, MN 56093 • 800 -247- 8256 • +1 (507) 833-8822 • www.EmersonConnectivity.com

142-0593-401 Related Products

142-0593-401 142-0593-406
Description CONNECTOR, PANEL MOUNT, CABLE TERMINATED, FEMALE, SMA CONNECTOR, SOLDER, JACK CONNECTOR, PANEL MOUNT, CABLE TERMINATED, FEMALE, SMA CONNECTOR, SOLDER, JACK
Reach Compliance Code unknown unknown
ECCN code EAR99 EAR99
Other features INSERTION LOSS MAX AT 10GHZ INSERTION LOSS MAX AT 10GHZ
Body/casing type JACK JACK
Characteristic impedance 50 Ω 50 Ω
Connector type RF SMA CONNECTOR RF SMA CONNECTOR
Contact to complete cooperation GOLD (30) GOLD (30)
Contact completed and terminated GOLD (30) GOLD (30)
Contact point gender FEMALE FEMALE
Coupling type THREADED THREADED
DIN compliance NO NO
Filter function NO NO
IEC compliance NO NO
Insertion loss 0.09 dB 0.09 dB
insulator material PTFE FLUOROCARBON/PFA PTFE FLUOROCARBON/PFA
JESD-609 code e4 e4
MIL compliance NO NO
Manufacturer's serial number SMA SMA
Installation method STRAIGHT STRAIGHT
Installation type CABLE CABLE
Maximum operating frequency 26.5 GHz 26.5 GHz
Options GENERAL PURPOSE GENERAL PURPOSE
Panel mounting YES YES
Termination type SOLDER SOLDER
voltage standing wave ratio 1.35 1.35
Base Number Matches 1 1
Help: IP and gateway are in different network segments
I encountered such a problem during development: The network where the device is located is quite special, and the gateway and IP are not in the same network segment. For example, IP: 192.168.0.2 mask...
liuxin00738 Embedded System
Analyzing the faults caused by the throttle valve
A Shanghai Volkswagen POL01.4L sedan was repaired because the EPC light was on and off. The fault diagnosis instrument Cheboshi A-2600 was connected to check the fault and found an occasional fault. T...
sertoip Automotive Electronics
MSP430 Program Library Digital Tube Display
Digital tubes are also one of the most commonly used output devices in single-chip microcomputer systems (along with liquid crystals, light-emitting diodes, etc.). Seven-segment (here we use eight seg...
tiankai001 Microcontroller MCU
Digital electronic clock!!!!
There are simulations and programs. Link: [url]http://pan.baidu.com/s/1bntnj0z[/url] Password: vklf...
火星撞地球 51mcu
About I2C Controller
Experts, I just learned FPGA not long ago, I have a question to ask you now How to write a multi-byte I2C controller? Verilog HDL is preferred...
jokeboy999 FPGA/CPLD
[Automatic clock-in walking timer system based on face recognition] Unboxing (1): SiPEED Maix Bit (K210)
Today, the development board of Digi-Key's Innovation Design Competition has finally arrived. I am full of excitement and anticipation! Here is an unboxing report and a hands-on experience! (I'll tell...
alanlan86 DigiKey Technology Zone

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1015  325  2159  832  2477  21  7  44  17  50 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号