EEWORLDEEWORLDEEWORLD

Part Number

Search

HI9P0506-5

Description
16-CHANNEL, SGL ENDED MULTIPLEXER, PDSO28
Categorysemiconductor    Analog mixed-signal IC   
File Size740KB,24 Pages
ManufacturerIntersil ( Renesas )
Websitehttp://www.intersil.com/cda/home/
Download Datasheet Parametric View All

HI9P0506-5 Overview

16-CHANNEL, SGL ENDED MULTIPLEXER, PDSO28

HI9P0506-5 Parametric

Parameter NameAttribute value
Number of functions1
Number of terminals28
Maximum operating temperature75 Cel
Minimum operating temperature0.0 Cel
Minimum supply/operating voltage10 V
Rated supply voltage15 V
Processing package descriptionPlastic, MS-013-AE, SOIC-28
stateDISCONTINUED
CraftsmanshipCMOS
packaging shapeRectangle
Package SizeSMALL OUTLINE
surface mountYes
Terminal formGULL WING
Terminal spacing1.27 mm
terminal coatingtin lead
Terminal locationpair
Packaging MaterialsPlastic/Epoxy
Temperature levelCOMMERCIAL EXTENDED
Number of inputs16
Maximum on-time1000 ns
Maximum off time1000 ns
Analog IC other typesSGL terminal multiplexer
Isolation Rating in Off State68 dB
Maximum limit analog input voltage15 V
Rated negative supply voltage-15 V
Maximum on-state resistance400 ohm
®
HI-506, HI-507, HI-508, HI-509
Data Sheet
October 30, 2007
FN3142.8
Single 16 and 8/Differential 8-Channel and
4-Channel CMOS Analog Multiplexers
The HI-506/HI-507 and HI-508/HI-509 monolithic CMOS
multiplexers each include an array of sixteen and eight
analog switches respectively, a digital decoder circuit for
channel selection, voltage reference for logic thresholds, and
an enable input for device selection when several
multiplexers are present. The Dielectric Isolation (DI)
process used in fabrication of these devices eliminates the
problem of latchup. DI also offers much lower substrate
leakage and parasitic capacitance than conventional junction
isolated CMOS (see Application Note AN520).
The switching threshold for each digital input is established by
an internal +5V reference, providing a guaranteed minimum
2.4V for logic “1” and maximum 0.8V for logic “0”. This allows
direct interface without pullup resistors to signals from most
logic families: CMOS, TTL, DTL and some PMOS. For
protection against transient overvoltage, the digital inputs
include a series 200Ω resistor and diode clamp to each
supply.
The HI-506 is a single 16-channel, the HI-507 is an
8-channel differential, the HI-508 is a single 8-channel and
the HI-509 is a 4-channel differential multiplexer.
If input overvoltages are present, the HI-546/HI-547/HI-548/
HI-549 multiplexers are recommended.
Features
• Pb-Free Available (RoHS Compliant) (See Ordering Info)
• Low ON Resistance . . . . . . . . . . . . . . . . . . . . . . . . 180Ω
• Wide Analog Signal Range
. . . . . . . . . . . . . . . . . . . . .
±15V
• TTL/CMOS Compatible
• Access Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250ns
• Maximum Power Supply . . . . . . . . . . . . . . . . . . . . . . 44V
• Break-Before-Make Switching
• No Latch-Up
• Replaces DG506A/DG506AA and DG507A/DG507AA
• Replaces DG508A/DG508AA and DG509A/DG509AA
• Pb-Free Available (RoHS Compliant)
Applications
• Data Acquisition Systems
• Precision Instrumentation
• Demultiplexing
• Selector Switch
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774
|
Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003, 2005, 2007. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
What is the difference between ADC12 and SD16?
I'm using FE427 recently and found that there is an SD16 for AD sampling on 427. Is there no ADC12 on 427? And what is the difference between the two?...
mzk1021 Microcontroller MCU
msp430g2553 usci_b0 spi mode problem
Mainly used launchpad msp430g2553's hardware spi to communicate with nrf24l01, has used usci_A0 serial port communication, now use usci_B0's spi to communicate with nrf24l01, io simulation can communi...
ayj12345 Microcontroller MCU
Issues with line width and wiring in PCB circuits
The chip I use has 80 pins, and the ground line is 1.5mm wide. Can't it be connected directly from the pin to 1.5mm? Can I connect 0.2mm first and then make the line wider to 1.5mm? Also, if the SMD c...
哒哒哒达到 PCB Design
This is my first time using PIC. I keep getting errors when configuring it. Please help me.
This is my first time using pic, but the simplest program always fails to compile. Please help me. The original code is in the attachment. __PROG_CONFIG(1,0xC100); __PROG_CONFIG(2,0x0A16); __PROG_CONF...
纻麻夏布 Microchip MCU
Please ask the moderator for I2C questions
void I2C_ADS1110_Init(void){GPIO_InitTypeDef GPIO_InitStructure;I2C_InitTypeDef I2C_InitStructure; /* GPIOB Periph clock enable */RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO |RCC_APB2Periph_GPIOB, ENAB...
friend stm32/stm8
How to select all device bit numbers or nominal values in the SCH file for AD1904 version
How to select all the device bit numbers or nominal values in the SCH file for AD1904 versionCan only one device be modified at a time? Waiting online... . . . . . . . . . . . . ....
btty038 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1988  557  2481  570  1015  41  12  50  21  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号