* Note that the surface mount MC26LS31D device uses the same die as in the plastic DIP
*
AM26LS31DC device, but with an MC prefix to prevent confusion with the package suffix.
MOTOROLA ANALOG IC DEVICE DATA
1
AM26LS31
MAXIMUM RATINGS
Rating
Power Supply Voltage
Input Voltage
Operating Ambient Temperature Range
Operating Junction Temperature Range
Storage Temperature Range
Symbol
VCC
VI
TA
TJ
Tstg
Value
8.0
5.5
0 to + 70
150
– 65 to + 150
Unit
Vdc
Vdc
°C
°C
°C
ELECTRICAL CHARACTERISTICS
(Unless otherwise noted, specifications apply 4.75 V
Typical values measured at VCC = 5.0 V, and TA = 25°C.)
Characteristic
Input Voltage – Low Logic State
Input Voltage – High Logic State
Input Current – Low Logic State
(VIL = 0.4 V)
Input Current – High Logic State
(VIH = 2.7 V)
(VIH = 7.0 V)
Input Clamp Voltage
(IIK = – 18 mA)
Output Voltage – Low Logic State
(IOL = 20 mA)
Output Voltage – High Logic State
(IOH = –20 mA)
Output Short Circuit Current
(VIH = 2.0 V) Note 1
Output Leakage Current – Hi–Z State
(VOL = 0.5 V, VIL(E) = 0.8 V, VIH(E) = 2.0 V)
(VOH = 2.5 V, VIL(E) = 0.8 V, VIH(E) = 2.0 V)
Output Leakage Current – Power OFF
(VOH = 6.0 V, VCC = 0 V)
(VOL = – 0.25 V, VCC = 0 V)
Output Offset Voltage Difference, Note 2
Output Differential Voltage, Note 2
Output Differential Voltage Difference, Note 2
Power Supply Current
(Output Disabled) Note 3
NOTES:
1. Only one output may be shorted at a time.
2. See EIA Specification EIA–422 for exact test conditions.
3. Circuit in three–state condition.
p
VCC
p
5.25 V and 0°C
p
TA
p
70°C.
Typ
–
–
–
Max
0.8
–
– 360
Unit
Vdc
Vdc
µA
µA
Symbol
VIL
VIH
IIL
IIH
Min
–
2.0
–
–
–
VIK
VOL
VOH
IOS
IO(Z)
–
–
IO(off)
–
–
VOS – VOS
VOD
∆V
OD
ICCX
–
2.0
–
–
–
–
2.5
– 30
–
–
–
–
–
–
+ 20
+ 100
– 1.5
0.5
–
– 150
V
V
V
mA
µA
–
–
–
–
–
–
–
60
– 20
+ 20
µA
+ 100
– 100
"
0.4
–
±
0.4
80
V
V
V
mA
SWITCHING CHARACTERISTICS
(VCC = 5.0 V, TA = 25°C unless otherwise noted.)
Characteristic
Propagation Delay Times
High to Low Output
Low to High Output
Output Skew
Propagation Delay – Control to Output
(CL = 10 pF, RL = 75
Ω
to Gnd)
(CL = 10 pF, RL = 180
Ω
to VCC)
(CL = 30 pF, RL = 75
Ω
to Gnd)
(CL = 30 pF, RL = 180
Ω
to VCC)
tPHZ(E)
tPLZ(E)
tPZH(E)
tPZL(E)
Symbol
tPHL
tPLH
Min
–
–
–
–
–
–
–
Typ
–
–
–
–
–
–
–
Max
20
20
6.0
30
35
40
45
ns
ns
Unit
ns
2
MOTOROLA ANALOG IC DEVICE DATA
AM26LS31
Figure 1. Three–State Enable Test Circuit and Waveforms
To Scope (Input)
Pulse generator characteristics
Zo = 50
Ω
PRR
3.0 V or Gnd
Input
Inv
Output
To Scope
Output
Open for tPZH(E) Test Only
+5V
p
1.0 MHz
p
6 ns
Pulse
Generator
Enable
Non–Inv
Output
CL
50
3.0 V
75
180
50% Duty Cycle
tTLH, tTHL
RL – See Test Table
CL Includes Probe and Jig Capacitance. See Test Table.
3.0 V
Control
Input
(Enable)
1.3 V
0
tPHZ(E)
Output
Output
0.5 V
VOH
Control
Input
(Enable)
tPZL(E)
1.3 V
VOL
0V
tPZH(E)
Output
1.3 V
0V
VOL
0V
VOH
1.3 V
0
3.0 V
≈
1.5 V
tPLZ(E)
Output
0.5 V
≈
1.5 V
Figure 2. Propagation Delay Times Input to Output Waveforms and Test Circuit
Scope
(Output)
Scope
(Input)
Inv
Output
200
5.0 V
Pulse
Generator
50
Non–Inv
Output
3.0 V
Enable
CL = 30 pF
75
Pulse generator characteristics
Zo = 50
Ω
PRR
p
1.0 MHz
p
6 ns
Input
1.3 V
tPHL
Output
1.3 V
1.3 V
0V
tPLH
VOH
1.3 V
VOL
0V
tPLH
Output
1.3 V
tPHL
VOH
1.3 V
VOL
0V
CL Includes Probe and Jig Capacitance
3.0 V
50% Duty Cycle
tTLH, tTHL
MOTOROLA ANALOG IC DEVICE DATA
3
AM26LS31
OUTLINE DIMENSIONS
D SUFFIX
PLASTIC PACKAGE
CASE 751B–05
(SO–16)
ISSUE J
9
–A–
16
–B–
1
8
P
8 PL
0.25 (0.010)
M
B
S
G
F
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0
_
7
_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0
_
7
_
0.229
0.244
0.010
0.019
K
C
–T–
SEATING
PLANE
R
X 45
_
M
D
16 PL
M
J
0.25 (0.010)
T B
S
A
S
DIM
A
B
C
D
F
G
J
K
M
P
R
–A–
16
9
PC SUFFIX
PLASTIC PACKAGE
CASE 648–08
ISSUE R
B
1
8
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
DIM
A
B
C
D
F
G
H
J
K
L
M
S
INCHES
MIN
MAX
0.740
0.770
0.250
0.270
0.145
0.175
0.015
0.021
0.040
0.70
0.100 BSC
0.050 BSC
0.008
0.015
0.110
0.130
0.295
0.305
0
_
10
_
0.020
0.040
MILLIMETERS
MIN
MAX
18.80
19.55
6.35
6.85
3.69
4.44
0.39
0.53
1.02
1.77
2.54 BSC
1.27 BSC
0.21
0.38
2.80
3.30
7.50
7.74
0
_
10
_
0.51
1.01
F
S
C
L
–T–
H
G
D
16 PL
SEATING
PLANE
K
J
T A
M
M
0.25 (0.010)
M
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
I am testing the UTMI high-speed interface chip I made. I use FPGA to simulate the device, and then connect the UTMI to the computer for communication. There is no problem with the handshake process a...
I connected the STM32 board to the computer via USB, but the power indicator on the board is not always on, but flickers on and off? What's going on? Is the voltage insufficient? Or is the voltage too...
Description of the phenomenon: 1. Under normal working conditions, WinCE 5.0+2443 platform detects that the HW Button is pressed in the PowerButton Driver, and broadcasts a message WM_OEM_POWERBUTTON_...
Why can't I download the program to the stc12 microcontroller? I am using a SMD microcontroller. I would like to ask if you have any comments or suggestions. Please feel free to give me your advice. I...
I've been studying the I2C module of MSP430F5438 recently, and I found that there aren't many related data and examples on the Internet. Most of the I2C communication is simulated using IO ports. Does...
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
