EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-7S2SC2642

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-7S2SC2642 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,

PH1-7S2SC2642 Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Communication standardsGR-253
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1530 nm
Nominal optical power output0.562 mW
minimum return loss-27 dB
Base Number Matches1
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Delay of ucosii
I am writing a program in ucosii, but when a delay occurs, it enters FaultISR (void); I have never encountered such a thing before! . I run it at full speed. After the chip is reset, it only executes ...
guozhiyang Microcontroller MCU
Recommended classic software testing materials (Part 26) - Commonly used document templates for software testing
[align=center][size=5][font=宋体]Recommendation of Classic Software Testing Materials (Twenty-six)[/font][font=Times New Roman]--[/font][/size][font=Times New Roman][size=5]Commonly Used Document Templa...
tiankai001 Download Centre
Essential tips for hardware engineers, 200 classic questions on analog electronics (101-200)
101. What is the most widely used power amplifier circuit at present?Answer: The most widely used power amplifier circuits are OTL and OCL circuits.102. What is crossover distortion?Answer: The transi...
Aguilera Analogue and Mixed Signal
Using an oscilloscope in Proteus 7 Professional
How to use an oscilloscope to observe the waves generated by an oscillator in Proteus 7 Professional software? The attachment contains the problems that occurred in the simulation....
cailinchongWHEE 51mcu
How to detect lithium battery voltage with MSP430
The project requires using solar energy to power the wireless sensor nodes. I first use solar energy to charge the lithium battery. Now I need to use MSP430 to detect the voltage of the lithium batter...
blb Microcontroller MCU
TI WEBENCH design tools
[color=rgb(144,144,144)]TI WEBENCH design tools: clock architecture tool, active filter design tool, power design tool, LDC design tool, light emitting diode (LED) design tool, sensor design tool! TI ...
德州仪器_视频 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1895  369  1495  1866  955  39  8  31  38  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号