EEWORLDEEWORLDEEWORLD

Part Number

Search

335-4010-C63

Description
Board Connector, 60 Contact(s), 6 Row(s), Male, Right Angle, Solder Terminal, LEAD FREE
CategoryThe connector    The connector   
File Size390KB,2 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

335-4010-C63 Overview

Board Connector, 60 Contact(s), 6 Row(s), Male, Right Angle, Solder Terminal, LEAD FREE

335-4010-C63 Parametric

Parameter NameAttribute value
package instructionLEAD FREE
Reach Compliance Codeunknown
Other featuresPANEL MOUNTABLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD
Contact completed and terminatedGOLD
Contact point genderMALE
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee4
MIL complianceNO
Mixed contactsNO
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of rows loaded6
OptionsGENERAL PURPOSE
Terminal pitch1.85 mm
Termination typeSOLDER
Total number of contacts60
Base Number Matches1
【Case Study】 Rigol spectrum analyzer base station signal test and Bluetooth frequency hopping signal test
When a laboratory in Xi'an was testing signals, it was found that the data always had relatively high bottom noise. Xi'an Antai test engineers suspected that there were radio transmitters around the l...
安泰测试设备 Test/Measurement
Analog Discovery 2 Review (6) Waveform Generator
[i=s]This post was last edited by cruelfox on 2019-12-8 12:17[/i]  In the previous article Analog Discovery 2 Review (5) Acquisition System Hardware Analysis , I introduced the analog/digital conversi...
cruelfox Test/Measurement
About STM32F103 GPIO operation and ODR, BRR, BSRR settings
When I was developing products using the stm32F103 series recently, some strange problems occurred during GPIO operations. The description is as follows:1. Using ODR to operate the PC port, because th...
吴通凯 stm32/stm8
Serial port configuration problem
8 data bits, 1 stop bit, no parity bit, how should ioctl be set specifically? Thank you!...
lnx Embedded System
Share: How to lay out a circuit board for an op amp
[size=4] During the circuit design process, application engineers often overlook the layout of the printed circuit board (PCB). A common problem encountered is that the circuit schematic is correct, b...
qwqwqw2088 Analogue and Mixed Signal
Using ADS software to adjust the flashing problem of the button trigger light
Now I want to use ads to adjust a simple program to trigger the light to flash. The existing program only has one phenomenon, Led_Display(0xff); the light on the ARM9 board turns on, and the 0x00 ligh...
pcshow Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2826  2018  2242  2808  1371  57  41  46  28  9 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号