5962-8874701ZA datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Power/power management> The power supply circuit> 5962-8874701ZA

5962-8874701ZA: DescriptionFixed Negative Standard Regulator, 12V, BIPolar, MBCY2, TO-66, 2 PIN; CategoryPower/power management The power supply circuit; File Size128KB，19 Pages; ManufacturerLinfinity Microelectronics

Download Datasheet Parametric View All

5962-8874701ZA Overview

Fixed Negative Standard Regulator, 12V, BIPolar, MBCY2, TO-66, 2 PIN

5962-8874701ZA Parametric

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
package instruction	TO-66, 2 PIN
Reach Compliance Code	unknown
Adjustability	FIXED
Nominal dropback voltage 1	1.8 V
Maximum absolute input voltage	35 V
Maximum input voltage	27 V
Minimum input voltage	14.5 V
JESD-30 code	O-MBCY-P2
JESD-609 code	e0
Maximum grid adjustment rate	0.05%
Maximum load regulation	0.06%
Number of functions	1
Output times	1
Number of terminals	2
Working temperatureTJ-Max	150 °C
Working temperature TJ-Min	-55 °C
Maximum output current 1	1 A
Maximum output voltage 1	12.36 V
Minimum output voltage 1	11.64 V
Nominal output voltage 1	12 V
Package body material	METAL
Encapsulate equivalent code	TO-213/-66
Package shape	ROUND
Package form	CYLINDRICAL
Certification status	Not Qualified
Regulator type	FIXED NEGATIVE SINGLE OUTPUT STANDARD REGULATOR
Filter level	MIL-PRF-38535
surface mount	NO
technology	BIPOLAR
Terminal surface	Tin/Lead (Sn/Pb) - hot dipped
Terminal form	PIN/PEG
Terminal location	BOTTOM
Maximum voltage tolerance	3%
Base Number Matches	1

Preview

Download Datasheet

View All

REVISIONS

LTR

DESCRIPTION

Add case outline N. Make changes to 1.2.2, 1.3, and figure 1. - ro

DATE (YR-MO-DA)

98-12-17

APPROVED

R. MONNIN

Add case outline 2. Make changes to 1.2.2, 1.3, table I, and figure 2. - ro

99-10-21

R. MONNIN

Add radiation hardness requirements. Add case outline M. Make changes to

1.2.2, 1.3, table I, figure 1, and figure 2. - ro

00-02-23

R. MONNIN

Add case outlines 4 and 5. - ro

01-05-18

R. MONNIN

Make pin assignment corrections to case outlines N and 5 as specified in

figure 2. - ro

02-04-15

R. MONNIN

Add a footnote to case outline U, TO-257 package as specified under 1.2.3

and figure 1. -rrp

05-02-04

R. MONNIN

For case outline T only, add footnote 1/ under 1.2.3 and make change to note 2

under figure 1. -rrp

06-01-23

R. MONNIN

THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.

REV

SHEET

REV

SHEET

REV STATUS

OF SHEETS

PMIC N/A

REV

SHEET

PREPARED BY

JOSEPH A. KERBY

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

CHECKED BY

CHARLES E. BESORE

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

http://www.dscc.dla.mil

APPROVED BY

MICHAEL A. FRYE

MICROCIRCUIT, LINEAR, 12 VOLT NEGATIVE

REGULATOR FIXED, MONOLITHIC SILICON

DRAWING APPROVAL DATE

89-09-14

AMSC N/A

REVISION LEVEL

SIZE

SHEET

CAGE CODE

67268

1 OF

5962-88747

DSCC FORM 2233

APR 97

5962-E157-06

1.3 Absolute maximum ratings.

Input voltage:

Operating or input shorted to ground ....................................................... -35 V dc

Transient .................................................................................................. -50 V dc 2/

Storage temperature range.......................................................................... -65°C to +150°C

Lead temperature (soldering, 10 seconds) .................................................. +300°C

Power dissipation (P

= +25°C:

Cases M, N, T, U, Z, 4, and 5............................................................... 15 W

Cases X and 2 ..................................................................................... 2 W

Case Y.................................................................................................. 20 W

= +25°C:

Cases M, N, T, U, and Z....................................................................... 3.0 W

Cases X and 2 ...................................................................................... 1.0 W

Case Y.................................................................................................. 3.6 W

Case 4 ................................................................................................. 1.7 W

Case 5 ................................................................................................. 1.3 W

Junction temperature (T

)............................................................................ +150°C 3/

Thermal resistance, junction-to-case (θ

Case M..................................................................................................... 5.5°C/W

Cases N and T ......................................................................................... 3.5°C/W

Case U ..................................................................................................... 4.2°C/W

Case X ..................................................................................................... 15°C/W

Case Y ..................................................................................................... 3°C/W

Case Z ..................................................................................................... 6°C/W

Case 2...................................................................................................... See MIL-STD-1835

Case 4 ..................................................................................................... 5.1°C/W

Case 5 ..................................................................................................... 3.6°C/W

Thermal resistance, junction-to-ambient (θ

Cases M, T, U, and Z .............................................................................. 42°C/W

Cases N, X, and 2 .................................................................................... 120°C/W

Case Y ..................................................................................................... 35°C/W

Case 4 ..................................................................................................... 60°C/W

Case 5 ..................................................................................................... 80°C/W

1.4 Recommended operating conditions.

Input voltage range (V

) ............................................................................. -14.5 V dc to -27 V dc

Ambient operating temperature range (T

).................................................. -55°C to +125°C

1.5 Radiation features:

Maximum total dose available (dose rate = 50 – 300 rads(Si) / s) ............... 300 Krads 4/

_____

2/ The 50-volt input rating refers to the ability of the regulator to withstand high line or transient conditions without

damage. Since the regulator’s maximum current capability is reduced, the output may fall out of regulation at high

input voltages under nominal loading.

3/ The device is protected by a thermal shutdown circuit which is designed to turn off the output transistor whenever the

device junction temperature is in excess of +150°C.

4/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.

Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883,

method 1019, condition A.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-88747

SHEET

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a

part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in

the solicitation or contract.

DEPARTMENT OF DEFENSE SPECIFICATION

MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-883 -

MIL-STD-1835 -

Test Method Standard Microcircuits.

Interface Standard Electronic Component Case Outlines.

DEPARTMENT OF DEFENSE HANDBOOKS

MIL-HDBK-103 -

MIL-HDBK-780 -

List of Standard Microcircuit Drawings.

Standard Microcircuit Drawings.

(Copies of these documents are available online at

http://assist.daps.dla.mil/quicksearch/

http://assist.daps.dla.mil

from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-

JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer

Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-

PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying

activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan

may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.

These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-

PRF-38535 is required to identify when the QML flow option is used.

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified

in MIL-PRF-38535, appendix A and herein.

3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.3 herein and figure 1.

3.2.2 Terminal connections. The terminal connections shall be specified on figure 2.

3.2.3 Radiation exposure circuit. The radiation exposure circuit shall be as specified on figure 3.

3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

as specified in table I and shall apply over the full ambient operating temperature range.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-88747

SHEET

Recommended Resources

"Strange trick" amplifier

Homemade 100Wx2HI-FI power amplifier

Thermocouple input circuit

Improved phase-shifted full-bridge ZVS main circuit

Air pressure switch automatic control circuit

Humidity control for greenhouse flower seedlings with bird chirping alarm circuit (MS01-B)

How to build Native application?: As the title says! I used win2k ddk to successfully do several examples before (3 years ago), but now I want to use winxp ddk and it always fails. Can anyone tell me the specific steps? Thank you...; flylmind Embedded System

Is there anyone who has been in charge of the hardware and can give me some guidance?: 17Electric race control:time:...; 混世小魔王 Electronics Design Contest

Can any experts help me to see why vxworks cannot be started under vmware. I have tried all the answers to similar questions on the Internet, but none of them can solve the problem. I hope an expert can solve it. I will be very grateful (see inside): I am a beginner in vxworks. I installed vxworks using vmware, but I can't start it. It keeps saying there is an error. I have searched a lot on the Internet and there are people with the same problem ...; feref Real-time operating system RTOS

A question about ldo (if you have seen it, please come and have a look): I just learned M3 and saw LDO. The description above is "provides stable power supply for the processor core and on-chip peripherals, provides stable power supply for the processor core and on-chip pe...; 51新手 Microcontroller MCU

Please help recommend: cost-effective microcontroller between 30 and 40 yuan: Please help recommend....; 64ye 51mcu

After wince starts to FMD::FMD_Init, it occasionally cannot continue to start!: After wince starts to FMD::FMD_Init, it occasionally cannot continue to start! It only occasionally cannot continue to start, and sometimes it can start again. Every time it is this place. Thank you...; chentaiyou Embedded System

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components