- 48-lead flatpack, 25 mil pitch (.390 x .640), wgt 1.4 Grams
DESCRIPTION
The 16-bit wide UT54ACS162245SLV MultiPurpose low volt-
age transceiver is built using Aeroflex’s epitaxial CMOS tech-
nology and is ideal for space applications. This high speed, low
power UT54ACS162245SLV low voltage transceiver is de-
signed to perform multiple functions including: asynchronous
two-way communication, Schmitt input buffering, voltage trans-
lation, warm and cold sparing. With V
DD
equal to zero volts, the
UT54ACS162245SLV outputs and inputs present a minimum
impedance of 1MΩ making it ideal for "cold spare" applications.
Balanced outputs and low "on" output impedance make the
UT54ACS162245SLV well suited for driving high capacitance
loads and low impedance backplanes. The
UT54ACS162245SLV enables system designers to interface 2.5
volt CMOS compatible components with 3.3 volt CMOS com-
ponents. For voltage translation, the A port interfaces with the
2.5 volt bus; the B port interfaces with the 3.3 volt bus. The
direction control (DIRx) controls the direction of data flow. The
output enable (OEx) overrides the direction control and disables
both ports. These signals can be driven from either port A or B.
The direction and output enable controls operate these devices
as either two independent 8-bit transceivers or one 16-bit trans-
ceiver.
LOGIC SYMBOL
OE1 (48)
OE2 (25)
(1)
DIR1
(47)
(46)
(44)
G1
G2
2EN1 (BA)
2EN2 (AB)
1EN1 (BA)
1EN2 (AB)
11
12
(24)
DIR2
1A1
1A2
1A3
(2)
(3)
(5)
(6)
(8)
1B1
1B2
1B3
1B4
(43)
1A4
(41)
1A5
(40)
1A6
(38)
1A7
(37)
1A8
(36)
2A1
2A2
2A3
(35)
(33)
21
22
1B5
(9)
1B6
(11)
1B7
(12)
1B8
(13)
2B1
(14)
2B2
(16)
2B3
(17)
2B4
(19)
2B5
(20)
2B6
(22)
2B7
(23)
2B8
(32)
2A4
(30)
2A5
(29)
2A6
(27)
2A7
(26)
2A8
PIN DESCRIPTION
Pin Names
OEx
DIRx
xAx
xBx
Description
Output Enable Input (Active Low)
Direction Control Inputs
Side A Inputs or 3-State Outputs (2.5V Port)
Side B Inputs or 3-State Outputs (3.3V Port)
1
PINOUTS
48-Lead Flatpack
Top View
DIR1
1B1
1B2
V
SS
1B3
1B4
VDD1
1B5
1B6
V
SS
1B7
1B8
2B1
2B2
V
SS
2B3
2B4
VDD1
2B5
2B6
V
SS
2B7
2B8
DIR2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
OE1
1A1
1A2
V
SS
1A3
1A4
VDD2
1A5
1A6
V
SS
1A7
1A8
2A1
2A2
V
SS
2A3
2A4
VDD2
2A5
2A6
V
SS
2A7
2A8
OE2
powered up first to ensure proper control of output enable
(/OEx) and direction control (DIRx). Control of the outputs /
OEx and DIRx pins is not guaranteed until V
DD2
reaches 1.5 +/
-5%. During normal operation of the device, after power up,
insure V
DD1
≥V
DD2
.
Power Up Sequence
Users should power up V
DD2
before V
DD1
because the DIRx
and /OEx pins on the UT54ACS162245SLV are powered by
V
DD2
. If V
DD1
is powered on first, V
DD2
must be powered on
within 1 second of V
DD1
reaching 1.5V +/-5%. An elevated
V
DD1
supply current up to 150mA may occur when
V
DD1
> 1.5V+/5% and V
DD2
< 1.5V +/-5%.
VDD1
VDD2
DIR1
OE1
DIR2
OE2
PORTA
Enable/
Direction
Control
Logic
Enable/
Direction
Control
Logic
PORTB
CORE
POWER TABLE
Port B
3.3 Volts
3.3 Volts
2.5 Volts
Port A
2.5 Volts
3.3 Volts
2.5 Volts
OPERATION
Voltage Translator
Non Translating
Non Translating
Warm Spare
Once the UT54ACS162245SLV is powered up with
V
DD1
≥
V
DD2
, the application may place the device into “Warm
Spare” mode by driving EITHER supply to V
SS
+/- 0.25V with
a maximum 1kΩ impedance between V
DDx
and V
SS
. While in
Warm Spare, the device places all outputs into a high im-
pedeance state (see DC electrical parameters, Iws).
FUNCTION TABLE
ENABLE
OEx
L
L
H
DIRECTION
DIRx
L
H
X
OPERATION
B Data To A Bus
A Data To B Bus
Isolation
Cold Spare
The UT54ACS162245SLV places the device into “Cold Spare”
mode when BOTH supplies are set to V
SS
+/- 0.25V with a
maximum 1KΩ impedance between V
DDx
and V
SS
. While in
Cold Spare, the device places all outputs into a high impedeance
state (see DC electrical parameters, Ics).
Power Application Guidelines
For proper operation, connect power to all V
DD
pins and ground
all V
SS
pins (i.e., no floating V
DD
or V
SS
supply pins). If V
DD1
and V
DD2
are not powered up together, then V
DD2
should be
2
LOGIC DIAGRAM
DIR1
(1)
(48)
OE1
DIR2
(24)
(25)
OE2
1A1
(47)
(2)
1B1
2A1
(36)
(13)
2B1
1A2
(46)
(3)
1B2
2A2
(35)
(14)
2B2
1A3
(44)
(5)
1B3
2A3
(33)
(16)
2B3
3.3 V PORT
2.5V PORT
2.5V PORT
(6)
1A5
(41)
(8)
1A6
(40)
(9)
1A7
(38)
(11)
1A8
(37)
(12)
1B4
(17)
2A5
(30)
(19)
2A6
(29)
(20)
2A7
(27)
(22)
2A8
(26)
(23)
2B4
1B5
2B5
1B6
2B6
1B7
2B7
1B8
2B8
3
3.3 V PORT
1A4
(43)
2A4
(32)
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEL Latchup
Neutron Fluence
(Note 2)
LIMIT
1.0E5
>113
1.0E14
UNITS
rad(Si)
MeV-cm
2
/mg
n/cm
2
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Not tested, inherent to CMOS technology.
ABSOLUTE MAXIMUM RATINGS
1
SYMBOL
V
I/O (Note 2)
V
DD1
V
DD2
T
STG
T
J (Note 3)
Θ
JC
I
I
P
D
PARAMETER
Voltage any pin
Supply voltage
Supply voltage
Storage Temperature range
Maximum junction temperature
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT (Mil only)
-.3 to V
DD1
+.3
-0.3 to 4.0
-0.3 to 4.0
-65 to +150
+150
20
±10
1
UNITS
V
V
V
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability and performance.
2. For Cold Spare mode (V
DD1
=VSS, V
DD2
=VSS), V
I/O
may be -0.3V to the maximum recommended operating level of V
DD1
+0.3V.
3. Maximum junction temperature may be increased to +175
The two functions of calling and sending text messages can be done by calling RILDrv directly. But when creating a connection, I choose Cellular Line and create a "My Connection" directly. After click...
[i=s]This post was last edited by lugl4313820 on 2022-1-29 23:33[/i]Today I use RT_Thread Studio to make a voltage meter. The project is based on the original SSD1306. Here I will mainly talk about ho...
[align=left][size=14pt][b]Introduction[/b]Designing and debugging a phase-locked loop[/i] (PLL) circuit can be complex unless the engineer has a deep understanding of PLL theory and the logical develo...
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
We know that microcontroller development tools generally include real-time online emulators and programmers. Among them, online emulators are very good tools, but they are also more expensive...[Details]
1. What is temperature?
Heat is a type of molecular motion. The hotter an object is, the faster its molecules move. Absolute zero is defined as the temperature at which all molecular motion ...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
Product series: PB-B-RS232/485 interface (hereinafter sometimes referred to as "interface") is a product in the PROFIBUS bus bridge series.
The main purpose of the bridge series ...[Details]
As a simple and practical input device, buttons have been used in various microcontroller application systems and are ubiquitous. However, the buttons used in different practical occasions are also...[Details]
Abstract: Aiming at the needs of coal-rock acoustic emission signal monitoring system, a data acquisition circuit with 24-bit resolution and 16-channel synchronous data acquisition function is desi...[Details]
hint:
The number of speakers and their spacing limit the sound field of a portable stereo system.
Spatial audio attempts to artificially recreate the experience of listening to sounds i...[Details]
1 Basic Features
In computer control systems and various intelligent instruments and meters composed of single-chip microcomputers (or microprocessors), various external analog signals must be ...[Details]
At present, a large number of cooling tower fans, speed fans and special fans are in use in petroleum, chemical, pharmaceutical, metallurgical and other enterprises. Some fans have no monitoring in...[Details]
Temperature compensated quartz crystal oscillator (TCXO) is widely used as a high-precision frequency source in communication systems, radar navigation systems, precision measurement and control sy...[Details]
Abstract: In order to realize wireless automatic alarm and monitoring of major safety places, based on the basic principle of pyroelectric infrared sensing, a detector for receiving infrared radia...[Details]
1 Load Regulation
Changes in power supply load will cause changes in power supply output. When the load increases, the output decreases, and vice versa, when the load decreases, the output inc...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
