5962-8855301ZX datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Power/power management> The power supply circuit> 5962-8855301ZX

5962-8855301ZX: DescriptionFixed Positive Standard Regulator, 15VMBFM2, METAL, TO-66, 2 PIN; CategoryPower/power management The power supply circuit; File Size136KB，20 Pages; ManufacturerLinfinity Microelectronics

Download Datasheet Parametric View All

5962-8855301ZX Overview

Fixed Positive Standard Regulator, 15VMBFM2, METAL, TO-66, 2 PIN

5962-8855301ZX Parametric

Parameter Name	Attribute value
package instruction	METAL, TO-66, 2 PIN
Reach Compliance Code	unknown
Maximum input voltage	30 V
Minimum input voltage	17.5 V
JESD-30 code	O-MBFM-P2
Number of functions	1
Number of terminals	2
Working temperatureTJ-Max	150 °C
Maximum output voltage 1	15.4 V
Minimum output voltage 1	14.6 V
Nominal output voltage 1	15 V
Package body material	METAL
Package shape	ROUND
Package form	FLANGE MOUNT
Certification status	Not Qualified
Regulator type	FIXED POSITIVE SINGLE OUTPUT STANDARD REGULATOR
Filter level	MIL-PRF-38535
surface mount	NO
Terminal form	PIN/PEG
Terminal location	BOTTOM
Base Number Matches	1

Preview

Download Datasheet

View All

REVISIONS

LTR

DESCRIPTION

Add case outlines T and U. Add vendors CAGE 69210 and U4637. Change

limits for line regulation, load regulation tests and standby current drain test at

temperature. Add temperature testing limit for Ripple rejection test.

Add case outline 2. Editorial changes throughout.

Add case outline N. Remove vendor CAGE 48726. Change vendor CAGE

U4637 to U3158. Editorial changes throughout.

Add CAGE 27851 and case outline M. Make changes to 1.2.2, 1.3, 1.4, table I,

figure 1, and figure 2. - ro

Add radiation hardness requirements. - ro

Make change to case outline N. Add case outlines 4 and 5. Make changes to

1.2.3, 1.3, figure 1, and figure 2. – rrp

Add a footnote to the case outline U, TO-257 package as specified under 1.2.2

and figure 1. Make corrections to package style descriptions under 1.2.2. - ro

For case outline “T” only, add a footnote 1/ under 1.2.3 and make change to

note 2 under figure 1. - ro

DATE (YR-MO-DA)

89-08-08

APPROVED

M. A. FRYE

92-03-30

96-01-17

M. A. FRYE

99-12-01

00-02-17

02-02-11

05-02-04

06-01-10

R. MONNIN

THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.

REV

SHEET

REV

SHEET

REV STATUS

OF SHEETS

PMIC N/A

REV

SHEET

PREPARED BY

JOSEPH A. KERBY

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

CHECKED BY

CHARLES E. BESORE

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

http://www.dscc.dla.mil

APPROVED BY

MICHAEL A. FRYE

MICROCIRCUIT, LINEAR, POSITIVE 15 VOLT

REGULATOR, FIXED, MONOLITHIC SILICON

DRAWING APPROVAL DATE

88-07-28

AMSC N/A

REVISION LEVEL

SIZE

SHEET

CAGE CODE

67268

1 OF

5962-88553

DSCC FORM 2233

APR 97

5962-E144-06

1.3 Absolute maximum ratings.

Input voltage:

Operating or output shorted to ground ........................................................ 35 V dc

Transient ..................................................................................................... 50 V dc 2/

Power dissipation (P

= +25°C:

Case M .....................................................................................................

Cases N, T, U, Z, 4, and 5 .......................................................................

Cases X and 2 .........................................................................................

Case Y .....................................................................................................

= +25°C:

Cases M, T, U, and Z ..............................................................................

Case N ....................................................................................................

Cases X and 2 .........................................................................................

Case Y .....................................................................................................

Case 4 .....................................................................................................

Case 5 .....................................................................................................

Storage temperature range..............................................................................

Lead temperature (soldering, 10 seconds) ......................................................

Junction temperature (T

)................................................................................

Thermal resistance, junction-to-case (θ

Case M.........................................................................................................

Cases N and T .............................................................................................

Case U .........................................................................................................

Case X .........................................................................................................

Case Y .........................................................................................................

Case Z .........................................................................................................

Case 2..........................................................................................................

Case 4 .........................................................................................................

Case 5 .........................................................................................................

Thermal resistance, junction-to-ambient (θ

Cases M, T, U, and Z ..................................................................................

Cases N, X and 2 ........................................................................................

Case Y .........................................................................................................

Case 4 .........................................................................................................

Case 5 .........................................................................................................

1.4 Recommended operating conditions.

Ambient operating temperature range (T

)...................................................... -55°C to +125°C

Input voltage range (V

) ................................................................................. +17.5 V dc to +30 V dc

1.5 Radiation features:

Maximum total dose available (dose rate = 50 – 300 rads (Si) / s) .................. 300 Krads (Si) 4/

18 W

15 W

20 W

3.0 W

1040 mW

1.0 W

4.3 W

1.7 W

1.3 W

-65°C to +150°C

+300°C

+150°C 3/

6.7°C/W

3.5°C/W

4.2°C/W

15°C/W

3°C/W

6°C/W

See MIL-STD-1835

5.1°C/W

3.6°C/W

42°C/W

120°C/W

29°C/W

60°C/W

80°C/W

The 50 volt input rating refers to the ability of the regulator to withstand high line or transient conditions without damage.

Since the regulator’s maximum current capability is reduced, the output may fall out of regulation at high input voltages

under nominal loading.

The device is protected by thermal shutdown circuit which is designed to turn off the output transistor whenever the

device junction temperature is in excess of +150°C.

These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.

Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883,

method 1019, condition A.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-88553

SHEET

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part

of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the

solicitation or contract.

DEPARTMENT OF DEFENSE SPECIFICATION

MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-883 -

MIL-STD-1835 -

Test Method Standard Microcircuits.

Interface Standard Electronic Component Case Outlines.

DEPARTMENT OF DEFENSE HANDBOOKS

MIL-HDBK-103 -

MIL-HDBK-780 -

List of Standard Microcircuit Drawings.

Standard Microcircuit Drawings.

(Copies of these documents are available online at

http://assist.daps.dla.mil/quicksearch/

http://assist.daps.dla.mil

from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-

JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer

Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-

PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying

activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan

may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.

These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-

PRF-38535 is required to identify when the QML flow option is used.

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified

in MIL-PRF-38535, appendix A and herein.

3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein and figure 1.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.

3.2.3 Radiation exposure circuit. The radiation exposure circuit shall be as specified on figure 3.

3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

as specified in table I and shall apply over the full ambient operating temperature range.

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical

tests for each subgroup are described in table I.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-88553

SHEET

Recommended Resources

Driving circuit diagram

Half-wave synchronous detection circuit composed of switching circuit

Replacement Thermostat Low Refrigerator Timer Controller Circuit

New ZTE GDH motor protector test circuit

Simple programmable timer

SAAl25l (television) infrared control receiving amplifier circuit

Design of Ethernet Controller Based on FPGA: [table=98%][tr][td][b]Introduction[/b] At present, Ethernet 802.3 protocol and TCP/IP protocol are the preferred protocols for embedded systems to access the Internet. The core idea of Ethernet is tha...; duminshe Embedded System

Recruiting verification engineers, process engineers and other positions: Shanghai company recruits the following positions. If you are interested, please send your resume to [email=xinjihr_cn@126.com]xinjihr_cn@126.com[/email], or msn: [email=mouhuitou@hotmail.com]mouhuito...; xinjihr Recruitment

MicroPython Hands-on (09) - Learn MaixPy face recognition from scratch: Face recognitionFrom ancient times to the present, face is an important way to identify people. In ancient times, in order to achieve the purpose of identifying specific people and preventing and arre...; eagler8 MicroPython Open Source section

Modification of cc2430 point-to-point communication program: The p1.4 port of cc2430 is set as a normal I/O to generate a pulse signal of about 10us. The p1.1 pin is set as an interrupt input pin. This pin receives a TTL level with a duration of t. L=C*t/2 is u...; 雪糕小冰棍 RF/Wirelessly

Experts, who can teach me the detailed settings of CCS using PROTEUS to simulate dsp? I can't understand the English of .cof file: My CCS version is V4. Since it is all in English, I don't know how to set it up. I hope the experts can give me some advice....; 420269467 DSP and ARM Processors

How to copy Alitum ROOM format to include copper pour?: As the title says, I have learned to reuse multi-channel layout and routing.But I have not found a way to copy the copper, because the board requires that the pads of each device need to be copper-rei...; 大小家伙好 PCB Design

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components