REVISIONS
LTR
A
DESCRIPTION
Add case outline U. Add vendor CAGE 69210 for device type 01UX. Editorial
changes throughout.
DATE (YR-MO-DA)
93-04-27
APPROVED
M. A. FRYE
B
Changes in accordance with NOR 5962-R138-96.
96-06-06
M. A. FRYE
C
Changes in accordance with NOR 5962-R187-96.
96-08-12
R. MONNIN
D
Add case outline E for vendor CAGE 27014. Update boilerplate. Editorial
changes throughout.
97-05-16
R. MONNIN
E
Add case outline X for vendor CAGE 27014. Make changes to 1.2.4, theta JC,
theta JA as specified in 1.3, dropout voltage test as specified in table I, and
figure 1. - ro
99-08-11
R. MONNIN
F
Add case outlines M and N for vendor CAGE 69210. - ro
02-03-29
R. MONNIN
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
SHEET
PREPARED BY
JOSEPH A. KERBY
F
1
F
2
F
3
F
4
F
5
F
6
F
7
F
8
F
9
F
10
F
11
F
12
F
13
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
CHARLES E. BESORE
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
APPROVED BY
MICHAEL A. FRYE
MICROCIRCUIT, LINEAR, 15-VOLT REGULATOR,
MONOLITHIC SILICON
DRAWING APPROVAL DATE
91-12-18
AMSC N/A
REVISION LEVEL
F
SIZE
A
SHEET
CAGE CODE
67268
1 OF
13
5962-90885
DSCC FORM 2233
APR 97
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
5962-E294-02
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and
M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the
Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the
PIN.
1.2 PIN. The PIN is as shown in the following example:
5962
Federal
stock class
designator
\
-
RHA
designator
(see 1.2.1)
\/
Drawing number
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and
are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
Generic number
LM2940-15
Circuit function
1.0 A, low dropout, 15-volt regulator
90885
01
Device
type
(see 1.2.2)
/
Q
Device
class
designator
(see 1.2.3)
E
Case
outline
(see 1.2.4)
X
Lead
finish
(see 1.2.5)
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as
follows:
Device class
M
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant,
non-JAN class level B microcircuits in accordance with MIL-PRF-38535,
appendix A
Certification and qualification to MIL-PRF-38535
Q or V
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
E
M
N
U
X
Y
Descriptive designator
GDIP1-T16 or CDIP2-T16
See figure 1
CBCC1-N3
See figure 1
GDFP1-G16
MBFM1-P2
Terminals
16
3
3
3
16
2
Package style
Dual-in-line
Flange mount, glass sealed with gull
wing leads
Bottom terminal chip carrier
TO-257, single row flange mount
with isolated tab, glass sealed
Flat pack with gullwing
Flange mount
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-90885
SHEET
F
2
1.3 Absolute maximum ratings. 1/
Input voltage (V
IN
):
Survival voltage (≤100 ms) ............................................................
Operational voltage .......................................................................
Internal power dissipation (P
D
) .........................................................
Storage temperature range ..............................................................
Lead temperature (soldering, 10 seconds) .......................................
Junction temperature (T
J
) .................................................................
Thermal resistance, junction-to-case (θ
JC
):
Cases E and U ..............................................................................
Cases X and Y ..............................................................................
Case M ..........................................................................................
Case N ..........................................................................................
Thermal resistance, junction-to-ambient (θ
JA
):
Case E ..........................................................................................
Case U ..........................................................................................
Case X ..........................................................................................
Case Y ..........................................................................................
Case M ..........................................................................................
Case N ..........................................................................................
1.4 Recommended operating conditions.
Ambient operating temperature range (T
A
) ...................................... -55°C to +125°C
Output current (I
O
) ............................................................................ 1 A
Input voltage (V
IN
) ............................................................................ 20 V dc
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in
the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the
solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 -
MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
60 V dc
26 V dc
Internally limited
-65°C to +150°C
300°C
+150°C
3°C/W
5°C/W
7.6°C/W
5.9°C/W
73°C/W
50°C/W
122°C/W
40°C/W
60°C/W
80°C/W
______
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-90885
SHEET
F
3
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.3 Electrical performance characteristics and post irradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and post irradiation parameter limits are as specified in table I and shall apply over the
full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space
limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the
RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535.
Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML” or “Q” as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this
drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535
and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2
herein) involving devices acquired to this drawing is required for any change as defined in MIL-PRF-38535, appendix A.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-90885
SHEET
F
4
TABLE I. Electrical performance characteristics.
Conditions
-55°C
≤
T
A
≤
+125°C
V
IN
= 20 V, I
O
= 1 A,
C
OUT
= 22
µF
unless otherwise specified
Output voltage
V
OUT
V
IN
= 20 V, I
O
= 5 mA
1
2,3
V
IN
= 16.75 V, I
O
= 5 mA
1
2,3
V
IN
= 17 V, I
O
= 5 mA
1
2,3
V
IN
= 26 V, I
O
= 5 mA
1
2,3
V
IN
= 20 V, I
O
= 1 A
1
2,3
V
IN
= 16.75 V, I
O
= 1 A
1
2,3
V
IN
= 16.75 V, I
O
= 50 mA
1
2,3
V
IN
= 20 V, I
O
= 50 mA
1
2,3
Maximum line transient
V
LT
V
O
≤
16 V, 2/
R
O
= 100
Ω,
t = 20 ms
Reverse polarity input
voltage dc
Reverse polarity input
voltage transient
V
RIN
V
RIT
R
O
= 100
Ω
2/
R
O
= 100
Ω,
t = 20 ms 2/
1,2,3
All
-15
V
1,2,3
All
All
All
All
All
All
All
All
All
Min
14.55
14.25
14.55
14.25
14.55
14.25
14.55
14.25
14.55
14.25
14.55
14.25
14.55
14.25
14.55
14.25
40
Max
15.45
15.75
15.45
15.75
15.45
15.75
15.45
15.75
15.45
15.75
15.45
15.75
15.45
15.75
14.45
15.75
V
V
V
V
V
V
V
V
V
Test
Symbol
Group A
subgroups
Device
type
Limits 1/
Unit
1,2,3
All
-45
V
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-90885
SHEET
F
5
京公网安备 11010802033920号
EEWORLD
