5962R8952001YX datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Power/power management> The power supply circuit> 5962R8952001YX

5962R8952001YX: DescriptionAdjustable Positive LDO Regulator,; CategoryPower/power management The power supply circuit; File Size60KB，13 Pages; ManufacturerOmnirel Corp.

Download Datasheet Parametric View All

5962R8952001YX Overview

Adjustable Positive LDO Regulator,

5962R8952001YX Parametric

Parameter Name	Attribute value
package instruction	,
Reach Compliance Code	unknown
Certification status	Not Qualified
Regulator type	ADJUSTABLE POSITIVE SINGLE OUTPUT LDO REGULATOR
total dose	100k Rad(Si) V
Base Number Matches	1

Preview

Download Datasheet

View All

REVISIONS

LTR

DESCRIPTION

Add case outline Y. Add vendor CAGE 69210. Editorial changes throughout.

Changes in accordance with N.O.R. 5962-R089-93.

Add radiation hardened requirements. Redrawn. - ro

DATE (YR-MO-DA)

90-06-21

93-03-15

00-03-01

APPROVED

M. A. FRYE

R. MONNIN

THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.

REV

SHEET

REV

SHEET

REV STATUS

OF SHEETS

PMIC N/A

REV

SHEET

PREPARED BY

GARY ZAHN

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

CHECKED BY

RAY MONNIN

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216

APPROVED BY

MICHAEL A. FRYE

MICROCIRCUIT, LINEAR, ADJUSTABLE

POSITIVE, LOW DROPOUT, VOLTAGE

REGULATOR, MONOLITHIC SILICON

DRAWING APPROVAL DATE

89-06-06

AMSC N/A

REVISION LEVEL

SIZE

SHEET

CAGE CODE

67268

1 OF

5962-89520

DSCC FORM 2233

APR 97

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

5962-E132-00

1.4 Recommended operating conditions.

Input to output voltage differential ............................................................... 25 V dc

Output current (I

OUT

)................................................................................... 10 mA

Full load current (I

)................................................................................... 5.0 A

Ambient operating temperature range (T

) ................................................. -55

C to +125

1.5 Radiation features:

Maximum total dose available (dose rate = 50 – 300 rads(Si) / s)............... 100 Krads 1/

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a

part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed

in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in

the solicitation.

SPECIFICATION

DEPARTMENT OF DEFENSE

MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.

STANDARDS

DEPARTMENT OF DEFENSE

MIL-STD-883 -

MIL-STD-973 -

MIL-STD-1835 -

HANDBOOKS

DEPARTMENT OF DEFENSE

MIL-HDBK-103 -

MIL-HDBK-780 -

List of Standard Microcircuit Drawings (SMD's).

Standard Microcircuit Drawings.

Test Method Standard Microcircuits.

Configuration Management.

Interface Standard For Microcircuit Case Outlines.

(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization

Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

1/ These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation

end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019,

condition A.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-89520

SHEET

3. REQUIREMENTS

3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-

JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer

Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-

PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying

activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan

may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.

These modifications shall not affect the PIN as described herein. A “Q” or “QML” certification mark in accordance with MIL-

PRF-38535 is required to identify when the QML flow option is used.

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as

specified in MIL-PRF-38535, appendix A and herein.

3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.3 herein and on figure 1.

3.2.2 Terminal connection(s). The terminal connection(s) shall be as specified on figure 2.

3.2.3 Radiation exposure circuit. The radiation exposure circuit shall be as specified on figure 3.

3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

as specified in table I and shall apply over the full ambient operating temperature range.

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical

tests for each subgroup are described in table I.

3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN

listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For

packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the

option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked.

3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an

approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to

listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-

38535, appendix A and the requirements herein.

3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided

with each lot of microcircuits delivered to this drawing.

3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,

appendix A.

3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's

facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the

reviewer.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-89520

SHEET

Recommended Resources

Stepper motor drive circuit composed of LB1836M

Multi-circuit processing pulse power supply circuit

Programmable voltage amplifier

Anti-theft sound and light alarm circuit diagram

Simple short-circuit braking circuit for three-phase motor

FAQs on debugging C2000+CLA+ on CCS: FAQs on debugging C2000+CLA+ on CCS...; Aguilera Microcontroller MCU

In AD interrupt, which register can be rewritten to disable AD interrupt?: I want to disable the program from entering the AD interruption in a certain process of the program to improve efficiency. The following sentence can be rewritten to the opposite to disable it, and th...; 面纱如雾 Microcontroller MCU

MSP430 MCU Tetris Game Programming: MSP430 MCU game program, Tetris, uses TI's official MSP430F5529 development board. TI's official development board, schematics are available online, and TI's official website also hasSource code:/*Tet...; Jacktang Microcontroller MCU

Precise Measurement and Comparison of Radiation Sensitivity of Modern Semiconductor Memories: This article describes some of the test methods that need to be considered to accurately measure the radiation sensitivity of modern high-security, high-speed semiconductor memories in time to prevent...; frozenviolet Automotive Electronics

MCS-51 single-chip microcomputer application development practical subroutines.: ...; wzt 51mcu

Design of a New Radar Signal Simulator: Abstract: A new radar signal simulator is designed, which can provide a variety of special radar signals, and the settings are flexible and convenient. When the user needs it, the software can be upgr...; JasonYoo Analog electronics

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components