The UT54ACS109E is a dual J-K positive triggered flip-flop.
A low level at the preset or clear inputs sets or resets the outputs
regardless of the other input levels. When preset and clear are
inactive (high), data at the J and K input meeting the setup time
requirements are transferred to the outputs on the positive-going
edge of the clock pulse. Following the hold time interval, data
at the J and K input can be changed without affecting the levels
at the outputs. The flip-flops can perform as toggle flip-flops
by grounding K and tying J high. They also can perform as D
flip-flops if J and K are tied together.
The devices are characterized over full HiRel temperature range
of -55°C to +125°C.
PINOUTS
16-Lead Flatpack
Top View
CLR1
J1
K1
CLK1
PRE1
Q1
Q1
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
CLR2
J2
K2
CLK2
PRE2
Q2
Q2
LOGIC SYMBOL
PRE1
J1
CLK1
K1
CLR1
PRE2
J2
(5)
(2)
(4)
(3)
(1)
(11)
(14)
(12)
(9)
Q2
(10)
Q2
S
J1
C1
K1
R
(6)
Q1
(7)
Q1
FUNCTION TABLE
INPUTS
PRE
L
H
L
H
H
H
H
H
CLR
H
L
L
H
H
H
H
H
CLK
X
X
X
↑
↑
↑
↑
L
J
X
X
X
L
H
L
H
X
K
X
X
X
L
L
H
H
X
OUTPUT
Q
H
L
H
1
L
Q
L
H
H
1
H
Toggle
No Change
H
L
CLK2
(13)
K2
(15)
CLR2
Note:
1. Logic symbol in accordance with ANSI/IEEE standard 91-1984 and
IEC Publication 617-12.
No Change
Note:
1. The output levels in this configuration are not guaranteed to meet the mini-
mum levels for V
OH
if the lows at preset and clear are near V
IL
maximum.
In addition, this configuration is nonstable; that is, it will not persist when
either preset or clear returns to its inactive (high) level.
1
LOGIC DIAGRAM
PRE
CLK
Q
J
Q
K
CLR
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
2
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+ .3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at these
or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended periods
may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
3.0 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS FOR THE UT54ACS109E
7
( V
DD
= 3.0V to 5.5V; V
SS
= 0V
6
; -55°C < T
C
< +125°C)
SYMBOL
V
IL
Description
Low-level input voltage
1
High-level input voltage
1
CONDITION
VDD
3.0V
5.5V
V
IH
3.0V
5.5V
I
IN
V
OL
Input leakage current
Low-level output voltage
3
High-level output voltage
3
Short-circuit output current
2 ,4
V
IN
= V
DD
or V
SS
I
OL
= 100μA
5.5V
3.0V
4.5V
V
OH
I
OH
= -100μA
3.0V
4.5V
I
OS
V
O
= V
DD
and V
SS
3.0V
5.5V
I
OL
Low level output current
9
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
I
OH
High level output current
9
V
IN
= V
DD
or V
SS
V
OH
= V
DD
-0.4V
P
total
I
DDQ
C
IN
C
OUT
Power dissipation
2, 8
Quiescent Supply Current
Input capacitance
5
Output capacitance
5
C
L
= 50pF
V
IN
= V
DD
or V
SS
ƒ
= 1MHz
ƒ
= 1MHz
3.0V
5.5V
3.0V
5.5V
5.5V
3.0V
5.5V
0V
0V
2.75
4.25
-100
-200
6
8
-6
-8
2.9
0.8
10
15
15
mW/
MHz
μA
pF
pF
mA
100
200
mA
mA
2.1
3.85
-1
1
0.25
0.25
V
μA
V
MIN
MAX
0.9
1.65
V
UNIT
V
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤5.0E5
amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765pF/
MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si) per MIL-STD-883 Method 1019 Condition A and section 3.11.2.
8. Power dissipation specified per switching output.
9. This value is guaranteed based on characterization data, but not tested.
[font=新宋体][size=4][color=royalblue][b]1. Precautions for car airbags[size=5][color=darkorange]>>[/color][/size] [/b][/color][/size][/font][url=https://bbs.eeworld.com.cn/thread-715-1-51.html][font=新宋体...
I want to set an external interrupt for GPIO_A2 but it has not worked. I wonder if I have added it less? The interrupt location (GPIO Port A) has been declared in tm4c123gh6pm_startup_ccs.c and the co...
Does the 9b92 C1 version of FLASH have a programming limit? How many times is it? I saw some people online saying that it is about 100 times. Is this correct?
Can you explain the following question at...
Saturated inductor is an inductor with a high hysteresis loop squareness ratio, high initial magnetic permeability, small coercive force, and a clear magnetic saturation point. It is often used as a c...
Why is there no REMOVE_DEVICE after SURPRISE_REMOVE? After installing a USB driver I wrote, I plugged in the device, the device started normally, and then directly unplugged the device. Sometimes I wo...
With the booming electronics industry, vision systems have become a leader in the electronics automation sector. However, the delicate nature of electronic products often affects product yields due...[Details]
Reflow soldering, a common soldering method in modern electronics manufacturing, primarily melts solder paste and pads to form solder joints. With technological advancements, soldering equipment ha...[Details]
On August 24th, media outlets reported, citing sources, that NavInfo, a listed company on the A-share market, is nearing completion in its acquisition of the intelligent driving c...[Details]
White light LEDs are voltage-sensitive devices. In actual operation, their upper limit is 20mA. However, the current often increases due to various reasons during use. If no protective measures are...[Details]
Zos Automotive Research Institute released the "2025
Smart Cockpit
Tier 1 Research Report (Domestic Edition)."
This report analyzes the operating conditions of more than a dozen ...[Details]
The Automotive Testing and Quality Assurance Expo (ATE 2025) will open on August 27th. At the expo, Rohde & Schwarz (R&S) will showcase six automotive testing solutions, themed "Intelligently Drivi...[Details]
Overview
As handheld voice communication devices become more and more popular, they are increasingly used in noisy environments, such as airports, busy roads, crowded bars, etc. In such noisy ...[Details]
There are basically three causes of spontaneous combustion of electric vehicles: The first is that the battery components are punctured or suffer fatal damage due to a collision accident, and part ...[Details]
Intel®
Xeon®
6
-
core processors now support the new Amazon EC2 R8i and R8i-flex instances on Amazon Web Services (AWS).
These new instances offer superior performance and fast...[Details]
Tools/Materials
Yitong Chuanglian MODBUS to PROFIBUS Gateway YT-PB-03
Siemens s7-300
This article describes how to configure the YT-PB-03 MODBUS to PROFIBUS gat...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
Driven by business opportunities such as access to new markets and government initiatives like the Belt and Road Initiative, global expansion has become a significant trend for Chinese companies. C...[Details]
Amid the increasing complexity of electronic system power management,
power architecture design
is undergoing a paradigm shift from experience-driven to tool-enabled.
Analog
Devices...[Details]
Yongxin Technology's BCL603S2H chipset integrates the nRF54L15 system-on-chip for monitoring various sensors and achieving seamless wireless connectivity.
Oslo, Norway – August 19, 2...[Details]
With the continuous advancement of technology, automation has become a ubiquitous technology, widely used in various industries. However, for many electricians, automation still seems like a diffic...[Details]
Automotive Electronics
京公网安备 11010802033920号
EEWORLD
