The UT54ACS165E is an 8-bit serial shift register that, when clocked,
shifts the data toward serial output Q
H
. Parallel-in access to each stage
is provided by eight individual data inputs that are enabled by a low
level at the SH/LD input. The devices feature a clock inhibit function
and a complemented serial output Q
H
.
Clocking is accomplished by a low-to-high transition of the CLK input
while SH/LD is held high and CLK INH is held low. The functions of
the CLK and CLK INH (clock inhibit) inputs are interchangeable.
Since a low CLK input and a low-to-high transition of CLK INH will
also accomplish clocking, CLK INH should be changed to the high
level only while the CLK input is high. Parallel loading is disabled
when SH/LD is held high. Parallel inputs to the registers are enabled
while SH/LD is low independently of the levels of CLK, CLK INH or
SER inputs.
The device is characterized over the full military temperature range of
-55°C to +125°C.
Note:
1. Q
n
= The state of the referenced output one setup time prior to the Low-to-
High clock transition.
LOGIC SYMBOL
(1)
SH/LD
(15)
CLK INH
(2)
CLK
(10)
SER
(11)
A
(12)
B
(13)
C
(14)
D
(3)
E
(4)
F
(5)
G
(6)
H
SRG8
C1 (LOAD)
≥1
C2/
PINOUT
16-Lead Flatpack
Top View
SH/LD
CLK
E
F
G
H
Q
H
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
CLK INH
D
C
B
A
SER
Q
H
2D
1D
1D
1D
(9)
Q
(7)
H
Q
H
Note:
1. Logic symbol in accordance with ANSI/IEEE Std 91-1984 and
IEC Publication 617-12.
1
LOGIC DIAGRAM
A
(11
)
SH/LD
B
(12)
C
(13)
D
(14)
E
(3)
F
(4)
G
(5)
H
(6)
(1)
CLK INH
CLK
(15)
(2)
S
C
SER
S
C
D Q
B
S
C
DQ
C
S
C
D Q
D
S
C
D Q
E
S
C
D Q
F
S
C
D Q
G
S
C
(9)
Q
H
(10
)
D
Q
A
(7)
D Q
H
R
R
R
R
R
R
R
R
Q
H
RADIATION HARDNESS SPECIFICATIONS
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
2
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+ .3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at these
or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended periods
may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
3.0 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS FOR THE UT54ACS165E
7
( V
DD
= 3.0V to 5.5V; V
SS
= 0V
6
; -55°C < T
C
< +125°C)
SYMBOL
V
IL
Description
Low-level input voltage
1
High-level input voltage
1
CONDITION
VDD
3.0V
5.5V
V
IH
3.0V
5.5V
I
IN
V
OL
Input leakage current
Low-level output voltage
3
High-level output voltage
3
Short-circuit output current
2 ,4
V
IN
= V
DD
or V
SS
I
OL
= 100µA
5.5V
3.0V
4.5V
V
OH
I
OH
= -100µA
3.0V
4.5V
I
OS
V
O
= V
DD
and V
SS
3.0V
5.5V
I
OL
Low level output current
9
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
I
OH
High level output current
9
V
IN
= V
DD
or V
SS
V
OH
= V
DD
-0.4V
P
total
I
DDQ
C
IN
C
OUT
Power dissipation
2, 8
Quiescent Supply Current
Input capacitance
5
Output capacitance
5
C
L
= 50pF
V
IN
= V
DD
or V
SS
ƒ
= 1MHz
ƒ
= 1MHz
3.0V
5.5V
3.0V
5.5V
5.5V
3.0V
5.5V
0V
0V
2.75
4.25
-100
-200
6
8
-6
-8
2.9
1.16
10
15
15
mW/
MHz
µA
pF
pF
mA
100
200
mA
mA
2.1
3.85
-1
1
0.25
0.25
V
µA
V
MIN
MAX
0.9
1.65
V
UNIT
V
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤5.0E5
amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765pF/
MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si) per MIL-STD-883 Method 1019 Condition B.
8. Power dissipation specified per switching output.
9. This value is guaranteed based on characterization data, but not tested.
A post on the English forum: " I started a company that teaches MicroPython with an ESP8266! "I was first introduced to MicroPython in an Internet of Things course during my junior year of college. I ...
《Kali Linux Penetration Technology Explained》 I just happened to have a Raspberry Pi B, which can be used to install Kali LinuxTP-LINK TL-WN722N wireless network card that I bought myselfRaspberry Pi ...
I disassembled a second-hand Yokogawa power meter I was using (a new one would cost 20,000 yuan), and looked at the reference source. The result was shocking... If I were to draw this board, it would ...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:00[/i] [size=13px][size=5][color=#8b0000]That is true. The trend is good for the survival of small-displacement cars, but rich people, ...
EtherCAT (Ethernet for Control Automation Technology) is a real-time industrial fieldbus communication protocol based on an Ethernet-based development framework. EtherCAT is one of the fastest indu...[Details]
As the main model among new energy vehicles, pure electric vehicles have received strong support and encouragement from the country in recent years, and their development is changing with each pass...[Details]
In recent years, with the application of the IEC61850 standard and the development and deployment of optoelectronic transformers, the concept of digital substations has been put into practical use ...[Details]
As time goes by, people are increasingly concerned about their own and their families' health. However, existing monitoring devices for individual vital signs have struggled to gain market share du...[Details]
1 Introduction
In the mid-1960s, American scientist Maas conducted extensive experimental research on the charging process of open-cell batteries and proposed an acceptable charging curve for ...[Details]
Amidst the wave of intelligent automotive transformation, advanced driver assistance is gradually emerging from cutting-edge technology into the mainstream, becoming a new frontier of industry comp...[Details]
On August 20th, Tiantai Robotics Co., Ltd., along with strategic partners including Shandong Future Robotics Technology Co., Ltd., Shandong Future Data Technology Co., Ltd., and Gangzai Robotics Gr...[Details]
Charging is a familiar process for new energy vehicles, and as a source of battery energy, charging piles are crucial. New energy vehicle charging can be divided into fast charging and slow chargin...[Details]
Through AI connection technology supported by Qualcomm X85 5G modem and RF and Qualcomm FastConnect 7900 mobile connection system, seamless switching can be achieved between cellular net...[Details]
During daily operation of an R-type power transformer, the voltage used varies as the equipment being used adjusts. This raises the question: can the transformer change voltage at this point? The a...[Details]
Charging is an essential topic for electric vehicles. Batteries are a core component of new energy vehicles. So, what's the optimal charge level for electric vehicles? Based on current battery tech...[Details]
Nascent Micro is launching devices covering a wide range of power applications, including gallium nitride (GaN) drivers, dual-channel automotive drivers, and battery protection MOSFETs.
...[Details]
0 Introduction
Portable terminals integrate a computer and display screen into a single device. Due to limited space in portable devices, previous designs often used a single-chip microcompute...[Details]
Keysight Technologies reported strong third-quarter results, with revenue and earnings per share exceeding expectations and steady order growth. The company, driven by strong growth across multiple...[Details]
Electronics engineers all know that transient voltage suppression (TVS) diodes are used to protect ports, preventing damage to downstream circuits caused by transient voltage surges. In short, TVS ...[Details]
Robotics Development
京公网安备 11010802033920号
EEWORLD
