Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
CC
= full range, T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at T
A
= +25°C and V
CC
= 3V.) (Note 1)
PARAMETER
V
CC
Range
SYMBOL
CONDITIONS
T
A
= 0°C to +70°C
T
A
= -40°C to +85°C
I
CC
MAX632_ only, V
CC
= 3.0V for V
TH
≤
2.93V,
V
CC
= 3.2V for V
TH
> 2.93V, no load
V
CC
= 5.5V, no load
T
A
= +25°C
Reset Threshold
V
TH
Table 1
T
A
= -40°C to +85°C
Reset Threshold Tempco
V
CC
to Reset Delay
Reset Active Timeout Period
RESET
Output Voltage
(MAX6326/MAX6328/
MAX6346/MAX6348)
RESET
Output Voltage
(MAX6326/MAX6346)
I
SINK
= 1.6mA, V
CC
> 2.1V, reset asserted
V
OL
I
SINK
= 100µA, V
CC
≥
1.2V, reset asserted
I
SOURCE
= 500µA, V
CC
= 3.2V, MAX6326 only
V
OH
I
SOURCE
= 800µA, V
CC
= 4.5V, V
TH
≤
4.38V
I
SOURCE
= 800µA, V
CC
= V
TH(MAX)
, V
TH
≥
4.5V
V
OH
RESET Output Voltage
(MAX6327/MAX6347)
V
OL
I
SOURCE
= 500µA, V
CC
≥
2.1V, reset asserted
I
SOURCE
= 50µA, V
CC
≥
1.2V, reset asserted
I
SINK
= 1.2mA, V
CC
≥
3.2V, reset not asserted,
MAX6327 only
I
SINK
= 3.2mA, V
CC
≥
4.5V, reset not asserted,
V
TH
≤
4.38V
I
SINK
= 3.2mA, V
CC
= V
TH(MAX)
, V
TH
≥
4.5V
RESET Threshold
Hysteresis
Open-Drain
RESET
Output
Leakage Current
Note 1:
Overtemperature limits are guaranteed by design and not production tested.
I want to design a two-stage low-noise amplifier for the RF front end. Is there anything I need to pay special attention to? For example, is there any problem if the two-stage low-noise amplifier is d...
[i=s]This post was last edited by jinglixixi on 2020-8-8 00:07[/i]The ESK32-360 development board is a development board with rich peripheral resources, so it is very difficult to find a free pin. I h...
if(IRCODE != 0xFF)
{
delay(); //Set a breakpoint here
TXIRCODE(IRCODE);
}Copy codeToday, I found a problem when I was working on infrared remote control reception. I used the capture function of TIM3 ...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
VP2188 is a color STN LCD module produced by Jingdian Pengyuan. This module is a dot matrix transmissive color STN display screen with a color scale of 65 k colors and white LED backlight. Its core...[Details]
OC faults may be the most frequent and the most frequent of all faults in the inverter. They alarm during the startup process, during the shutdown process, during operation, and even when powered o...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
Preface
In recent years, white light LEDs have gradually replaced incandescent bulbs and fluorescent lamps because they have unparalleled advantages over traditional light sources in terms...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
0 Introduction
With the rapid development of social economy and science and technology, electric locomotives, subways and electric vehicles will be widely used. The power conversion and cont...[Details]
The DisplayPort interface standard is approved by the Video Electronics Standards Association (VESA) to provide an open, scalable standard for the entire industry. The development of DisplayPort ca...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
