The UT54ACS165E is an 8-bit serial shift register that, when clocked,
shifts the data toward serial output Q
H
. Parallel-in access to each stage
is provided by eight individual data inputs that are enabled by a low
level at the SH/LD input. The devices feature a clock inhibit function
and a complemented serial output Q
H
.
Clocking is accomplished by a low-to-high transition of the CLK input
while SH/LD is held high and CLK INH is held low. The functions of
the CLK and CLK INH (clock inhibit) inputs are interchangeable.
Since a low CLK input and a low-to-high transition of CLK INH will
also accomplish clocking, CLK INH should be changed to the high
level only while the CLK input is high. Parallel loading is disabled
when SH/LD is held high. Parallel inputs to the registers are enabled
while SH/LD is low independently of the levels of CLK, CLK INH or
SER inputs.
The device is characterized over the full military temperature range of
-55°C to +125°C.
Note:
1. Q
n
= The state of the referenced output one setup time prior to the Low-to-
High clock transition.
LOGIC SYMBOL
(1)
SH/LD
(15)
CLK INH
(2)
CLK
(10)
SER
(11)
A
(12)
B
(13)
C
(14)
D
(3)
E
(4)
F
(5)
G
(6)
H
SRG8
C1 (LOAD)
≥1
C2/
PINOUT
16-Lead Flatpack
Top View
SH/LD
CLK
E
F
G
H
Q
H
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
CLK INH
D
C
B
A
SER
Q
H
2D
1D
1D
1D
(9)
Q
(7)
H
Q
H
Note:
1. Logic symbol in accordance with ANSI/IEEE Std 91-1984 and
IEC Publication 617-12.
1
LOGIC DIAGRAM
A
(11
)
SH/LD
B
(12)
C
(13)
D
(14)
E
(3)
F
(4)
G
(5)
H
(6)
(1)
CLK INH
CLK
(15)
(2)
S
C
SER
S
C
D Q
B
S
C
DQ
C
S
C
D Q
D
S
C
D Q
E
S
C
D Q
F
S
C
D Q
G
S
C
(9)
Q
H
(10
)
D
Q
A
(7)
D Q
H
R
R
R
R
R
R
R
R
Q
H
RADIATION HARDNESS SPECIFICATIONS
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
2
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+ .3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at these
or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended periods
may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
3.0 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS FOR THE UT54ACS165E
7
( V
DD
= 3.0V to 5.5V; V
SS
= 0V
6
; -55°C < T
C
< +125°C)
SYMBOL
V
IL
Description
Low-level input voltage
1
High-level input voltage
1
CONDITION
VDD
3.0V
5.5V
V
IH
3.0V
5.5V
I
IN
V
OL
Input leakage current
Low-level output voltage
3
High-level output voltage
3
Short-circuit output current
2 ,4
V
IN
= V
DD
or V
SS
I
OL
= 100µA
5.5V
3.0V
4.5V
V
OH
I
OH
= -100µA
3.0V
4.5V
I
OS
V
O
= V
DD
and V
SS
3.0V
5.5V
I
OL
Low level output current
9
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
I
OH
High level output current
9
V
IN
= V
DD
or V
SS
V
OH
= V
DD
-0.4V
P
total
I
DDQ
C
IN
C
OUT
Power dissipation
2, 8
Quiescent Supply Current
Input capacitance
5
Output capacitance
5
C
L
= 50pF
V
IN
= V
DD
or V
SS
ƒ
= 1MHz
ƒ
= 1MHz
3.0V
5.5V
3.0V
5.5V
5.5V
3.0V
5.5V
0V
0V
2.75
4.25
-100
-200
6
8
-6
-8
2.9
1.16
10
15
15
mW/
MHz
µA
pF
pF
mA
100
200
mA
mA
2.1
3.85
-1
1
0.25
0.25
V
µA
V
MIN
MAX
0.9
1.65
V
UNIT
V
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤5.0E5
amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765pF/
MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si) per MIL-STD-883 Method 1019 Condition B.
8. Power dissipation specified per switching output.
9. This value is guaranteed based on characterization data, but not tested.
A large number of various wires need to be laid in a monitoring system. On the one hand, it consumes a lot of manpower, and on the other hand, it also consumes a lot of copper and plastic. It is reall...
[align=left][size=4][b]----Definition and implementation of inverter real-time data for FLASH----[/b][/size][/align][align=left][size=4]Now we need to define a reliable FLASH internal data management ...
I believe everyone had a lot of questions when watching Journey to the West as a child, but as we grew older, we took these questions for granted. One day, when I saw the black-back comics, all these ...
There was a typhoon and heavy rain in the past two days, but fortunately the things were packed tightly and nothing went wrong. The letter from EEWORLD is so warm!!! So touching!!! I often visit EEWOR...
There are still a few days before the Chinese New Year. I went home to worship my ancestors recently and took a few photos with my mobile phone. The "Find the New Year's Spirit" activity requires 3 ph...
When using ARM to directly read the TLC2543 AD chip, the conversion results all start at 4 bits, that is, the first data is 1000, and the second data is not 996 or 1004. Other data such as 1001, 1002,...
According to foreign media reports, Ford Motor has applied to the U.S. Patent and Social Security Administration (USPTO) for a patent for a remote vehicle control system that may be used in future ...[Details]
On August 24th, Jin Yuzhi, CEO of Huawei's Intelligent Automotive Solutions BU, announced the first automotive application of Huawei Qiankun's unique Limera technology. This technology eliminates t...[Details]
Flip-chip and ball grid array (BGA) are two widely used packaging technologies in the electronics industry. Each has its own advantages and limitations, and in some cases, they can complement each ...[Details]
When we travel in cities, we all find that electric vehicles have many advantages. As a means of transportation, they can also fulfill their mission well. Now, more and more residential communities...[Details]
According to foreign media reports, secondary battery materials company POSCO Future M announced that it has successfully developed two experimental (prototype) positive electrode materials for the...[Details]
According to foreign media reports, BMW has just been granted a patent for a screen that could cover the entire roof. BMW hopes to transform at least a portion of the vehicle's headliner into a dis...[Details]
When discussing autonomous driving technology, there are often two extremes: on the one hand, there's the vision of "fully autonomous driving," while on the other, there's concern about potential s...[Details]
This paper proposes a temperature real-time transmission and display solution based on LED optical data transmission, with Jingwei Yager low-power FPGA HR (Yellow River) series as the main controll...[Details]
Keysight Technologies is combining its electromagnetic simulator with Synopsys' AI-driven RF design migration flow to create an integrated design flow for migrating from TSMC's N6RF+ process techno...[Details]
In the electronics manufacturing industry, surface mount technology (SMT) placement machines are core equipment for production lines. However, with many different models available on the market, ch...[Details]
With the continuous development of the industrial automation industry, we are seeing an increasing number of intelligent devices using flexible, efficient, and precise robotic arms to p...[Details]
Plessey Semiconductors has been acquired by Haylo Labs, which was established in March last year with a $100 million, five-year loan from Chinese technology company Goertek.
Haylo Labs w...[Details]
The difference between a series inverter and a parallel inverter is that they use different oscillation circuits. A series inverter connects L, R, and C in series, while a parallel inverter connect...[Details]
Plug-in hybrid vehicles (PHEVs) utilize two powertrains. Their pure electric range is typically inferior to that of pure electric vehicles, often reaching less than half that. Currently, mainstream...[Details]
On August 21, it was reported that Intel's new generation of AI chip Jaguar Shores was recently exposed for the first time.
According to photos shared by Andreas Schilling, the Jaguar Shores t...[Details]
Mobile and portable
京公网安备 11010802033920号
EEWORLD
