EEWORLDEEWORLDEEWORLD

Part Number

Search

51741-30003202CCLF

Description
Board Connector, 34 Contact(s), 4 Row(s), Female, Straight, Press Fit Terminal, Receptacle, LEAD FREE
CategoryThe connector    The connector   
File Size227KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51741-30003202CCLF Overview

Board Connector, 34 Contact(s), 4 Row(s), Female, Straight, Press Fit Terminal, Receptacle, LEAD FREE

51741-30003202CCLF Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerAmphenol
package instructionLEAD FREE
Reach Compliance Codecompliant
Other featuresTERMINAL PITCH FOR POWER CONTACTS: 6.35 MM
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (30) OVER NICKEL (50)
Contact completed and terminatedGOLD (5) OVER NICKEL (50)
Contact point genderFEMALE
Contact materialCOPPER ALLOY
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee4
MIL complianceNO
Manufacturer's serial number51741
Mixed contactsYES
Installation methodSTRAIGHT
Installation typeBOARD
Number of rows loaded4
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typePRESS FIT
Total number of contacts34
UL Flammability Code94V-0
Base Number Matches1
PDM: Rev:L
STATUS:
Released
Printed: Dec 20, 2010
.
The constant current diagram of AP4313 is as follows; is the internal block diagram an amplifier or a comparator?
I heard from a friend on a forum: "Increasing the optocoupler's current-limiting resistor actually reduces the optocoupler's current, increases the duty cycle, and slightly increases the output voltag...
czf0408 LED Zone
STM32F103 timer clock not understood
Today I saw a blog post that says: Assuming the system clock is 72Mhz, TIM1 is derived from PCLK2 (72MHz), and TIM2-7 is derived from PCLK1. The key is to set the clock pre-division number and the val...
ddllxxrr stm32/stm8
51 MCU serial communication problem
There is no serial port protocol between the upper and lower computers. When one side is ready to receive, the other side can send. Now the question is how can the receiver know that the data stream h...
manly88 Embedded System
Jlink debugging often shows "could not transfer JTAG data"
When running naked, I debugged with ADS and this problem occurred after running for a few minutes. The time is not fixed, sometimes a few minutes, sometimes more than ten minutes. But if it is burned ...
wangjunaza Embedded System
Introduction to CY7C68013-I-USB2.0 Development Learning Board
Why choose CY7C68013 as USB2.0 chip: 1. High cost performance, the largest market share in the world among general USB2.0 interface chips, and the largest foreign market share. 2. Maximum 4K USB endpo...
dz51 MCU
I made a clock, and the microcontroller displays garbled characters when the clock jumps to the date. I would be very grateful for your help.
Dear experts, please help me find the error. This is a single-chip computer program of mine. It is a clock. It uses ATMEL89C51 single-chip computer and is displayed on the digital tube 7SEG-MPX8-CC-BL...
ATMEGA_007 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1886  545  343  2748  1928  38  11  7  56  39 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号