EEWORLDEEWORLDEEWORLD

Part Number

Search

CAT1026YI-42-GT2

Description
2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
Categoryaccessories   
File Size227KB,20 Pages
ManufacturerCatalyst
Websitehttp://www.catalyst-semiconductor.com/
Download Datasheet View All

CAT1026YI-42-GT2 Overview

2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8

CAT1026, CAT1027
Dual Voltage Supervisory Circuits with
I
2
C Serial 2k-bit CMOS EEPROM
FEATURES
Precision V
CC
Power Supply Voltage Monitor
5V, 3.3V and 3V systems
Five threshold voltage options
Additional voltage monitoring
Externally adjustable down to 1.25V
Watchdog timer (CAT1027 only)
Active High or Low Reset
Valid reset guaranteed at V
CC
= 1V
400kHz I
2
C Bus
2.7V to 5.5V Operation
Low power CMOS technology
16-Byte Page Write Buffer
Built-in inadvertent write protection
1,000,000 Program/Erase cycles
Manual Reset capability
100 year data retention
Industrial and extended temperature ranges
8-pin DIP, SOIC, TSSOP, MSOP or TDFN
(3 x 3mm foot-print) packages
TDFN max height is 0.8mm
For Ordering Information details, see page 19.
The CAT1027 is designed with a 1.6 second
watchdog timer circuit that resets a system to a known
state if software or a hardware glitch halts or “hangs”
the system. The CAT1027 features a watchdog timer
interrupt input, WDI.
The on-chip 2k-bit EEPROM memory features a 16-byte
page. In addition, hardware data protection is provided
by a V
CC
sense circuit that prevents writes to memory
whenever V
CC
falls below the reset threshold or until V
CC
reaches the reset threshold during power up.
Available packages include 8-pin DIP and surface
mount, 8-pin SO, 8-pin TSSOP, 8-pin TDFN and 8-pin
MSOP packages. The TDFN package thickness is
0.8mm maximum. TDFN footprint is 3 x 3mm.
supply monitor and reset circuit protects memory and
systems controllers during power up/down and
against brownout conditions. If power supply voltages
are out of tolerance reset signals become active
preventing the system microcontroller, ASIC, or
peripherals from operating.
The CAT1026 features two open drain reset outputs:
¯¯¯¯¯¯
one (RESET) drives high and the other (RESET)
drives low whenever V
CC
falls below the threshold.
Reset outputs become inactive typically 200ms after
the supply voltage exceeds the reset threshold value.
With both active high and low reset signals, interface
to microcontrollers and other ICs is simple. CAT1027
¯¯¯¯¯¯
¯¯¯¯¯¯
has only a RESET output. In addition, the RESET pin
can be used as an input for push-button manual reset
capability.
The CAT1026 and CAT1027 provide an auxiliary
voltage sensor input, V
SENSE
, which is used to monitor
a second system supply. The auxiliary high impe-
dance comparator drives the open drain output, V
LOW
,
whenever the sense voltage is below 1.25V threshold.
DESCRIPTION
The CAT1026 and CAT1027 are complete memory
and supervisory solutions for microcontroller-based
systems. A 2k-bit serial EEPROM memory and a
system power supervisor with brown-out protection
are integrated together in low power CMOS techno–
logy. Memory interface is via a 400kHz I
2
C bus.
The CAT1026 and CAT1027 provide a precision V
CC
sense circuit with five reset threshold voltage options
that support 5V, 3.3V and 3V systems. The power
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
1
Doc. No. MD-3010 Rev. M
[Forward] Video: Renesas Electronics EZ-CUBE_ R7F0C80212ESP Experience Lecture Video. Did nmg post it in the wrong place?
[url=https://bbs.eeworld.com.cn/thread-446484-1-1.html]https://bbs.eeworld.com.cn/thread-446484-1-1.html[/url]...
johnrey Renesas Electronics MCUs
Problems encountered in keil uv3 debugging
[img]http://img.my.csdn.net/uploads/201211/09/1352455005_6997.jpg[/img]Hi everyone, I encountered the same problem when I was debugging a 51 program with KEIL. I selected software simulation mode and ...
renyunpei 51mcu
Urgently looking for a CD for the ZRtech FPGA development board
I bought the ZRtech FPGA cyclone IV development board kit in January 2013, see: [url]http://item.taobao.com/item.htm?spm=a1z09.2.9.90.qC6ODJ&id=15988547416&_u=11uthho495f[/url] Now I can't find the CD...
xiagong FPGA/CPLD
Xiaobai, please teach me how to use stepper motor
I have a 4-phase stepper motor controlled by ULN2003A. Now I want to use the driver to control a 24V 2-phase stepper motor. How should I change the program?...
fafafafather 51mcu
Where are PCB professionals heading?
I came across this article by accident. It is really well written. I would like to share it with you all. . . Understanding the future of circuit board layout professionals is an important issue in it...
led2015 Talking
USB 2.0 protocol
Does anyone have the USB 2.0 protocol? Upload it. I'm having a hard time finding it!...
wall_e FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2451  1670  486  1867  2332  50  34  10  38  47 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号