EEWORLDEEWORLDEEWORLD

Part Number

Search

51704-11510015C0

Description
Board Connector, 130 Contact(s), 4 Row(s), Male, Straight, Press Fit Terminal
CategoryThe connector    The connector   
File Size274KB,4 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

51704-11510015C0 Overview

Board Connector, 130 Contact(s), 4 Row(s), Male, Straight, Press Fit Terminal

51704-11510015C0 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerAmphenol
Reach Compliance Codecompliant
Other featuresTERMINAL PITCH FOR POWER CONTACTS: 6.35 MM
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (30) OVER NICKEL (50)
Contact completed and terminatedTIN LEAD (100) OVER NICKEL (50)
Contact point genderMALE
Contact materialCOPPER ALLOY
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee0
MIL complianceNO
Manufacturer's serial number51704
Mixed contactsYES
Installation methodSTRAIGHT
Installation typeBOARD
Number of rows loaded4
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typePRESS FIT
Total number of contacts130
UL Flammability Code94V-0
Base Number Matches1
PDM: Rev:L
STATUS:
Released
Printed: Sep 18, 2008
.
Power supply noise interference processing
一般而言,电源杂讯干扰的传播途径可分为下列二大类:??一、普通模式(Normal Mode):简称通模,指的就是二组输入电源线之间的杂讯。这些杂讯大多是由开关动作或者是静态功率转换器等干扰所造成,当这些干扰与正常讯号重叠在一起时,器材元件是无法分辨的,因为正常讯号也是以通模的状态存在。 ??二、共通模式(Common Mode):简称共模,指的是电源与接地之间的杂讯。这部分杂讯的起因多数是因为接地...
songbo Industrial Control Electronics
Principle of LED brightness control by microcontroller MCU
Microcontrollers MCU are usually considered digital devices. By default, their output voltage level is either high or low, not a neutral value. To achieve the requirement of LED brightness control, th...
火辣西米秀 Microcontroller MCU
Can the register secondary latch be latched correctly?
always@(posedge clk or negedge rst_n) begin ......... areg1<=a; areg2<=areg1; .... end assign a=~areg1& areg2;//High level is valid always@(posedge clk or negedge rst_n) begin ........... if(a) .........
1559638992 FPGA/CPLD
TI's BQ2057 charging current is only 200mA. Please give me some advice based on the picture above!
Using a 5V2A adapter, a lithium battery is fully charged to 4.1V, but the charging current is less than 200mA, the charging speed is too slow. See the picture, please improve...
ZHANGXU716 Analogue and Mixed Signal
[Transfer] Common questions in op amp learning
[i=s] This post was last edited by dontium on 2015-1-23 11:31 [/i] [b]1. What is the function of adding a small resistor to the output of the op amp? [/b] Answer: The protection method for short-circu...
模拟IC Analogue and Mixed Signal
A Deeper Study of "Ground" in Circuits
[i=s]This post was last edited by ohahaha on 2015-12-4 14:21[/i] [color=rgb(62,62,62)][align=left][Repost] If someone asks "Is there a universal grounding method that can be used as a reference?" I wi...
ohahaha Energy Infrastructure?

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 249  2799  217  181  173  6  57  5  4  31 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号