Asynchronous operation for compatibility with industry-
standard 512K x 8 SRAMs
TTL compatible inputs and output levels, three-state
bidirectional data bus
Typical radiation performance
- Total dose: 30krad(Si)
- 30krad(Si) to 300krad(Si), depending on orbit, using
Aeroflex UTMC patented shielded package
- SEL Immune >80 MeV-cm
2
/mg
- LET
TH
(0.25) = 5MeV-cm
2
/mg
- Saturated Cross Section (cm
2
) per bit, ~1.0E-7
- 1.5E-8 errors/bit-day, Adams 90% geosynchronous
heavy ion
Packaging options:
- 32-lead ceramic flatpack (weight 2.5-2.6 grams)
Standard Microcircuit Drawing 5962-99606
- QML T and Q compliant
INTRODUCTION
The QCOTS
TM
UT7Q512 Quantified Commercial Off-the-
Shelf product is a high-performance CMOS static RAM
organized as 524,288 words by 8 bits. Easy memory expansion
is provided by an active LOW Chip Enable (E), an active LOW
Output Enable (G), and three-state drivers. This device has a
power-down feature that reduces power consumption by more
than 90% when deselected
.
Writing to the device is accomplished by taking the Chip Enable
One (E) input LOW and the Write Enable (W) input LOW. Data
on the eight I/O pins (DQ
0
through DQ
7
) is then written into the
location specified on the address pins (A
0
through A
18
). Reading
from the device is accomplished by taking Chip Enable One (E)
and Output Enable (G) LOW while forcing Write Enable (W)
HIGH. Under these conditions, the contents of the memory
location specified by the address pins will appear on the eight I/
O pins.
The eight input/output pins (DQ
0
through DQ
7
) are placed in a
high impedance state when the device is deselected (E, HIGH),
the outputs are disabled (G HIGH), or during a write operation
(E LOW and W LOW).
Clk. Gen.
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
Pre-Charge Circuit
Row Select
Memory Array
1024 Rows
512x8 Columns
I/O Circuit
Column Select
Data
Control
CLK
Gen.
A10
A11
A12
A13
A14
A15
A16
A17
A18
DQ
0
- DQ
7
E
W
G
Figure 1. UT7Q512 SRAM Block Diagram
1
PIN NAMES
A(18:0)
DQ(7:0)
E
W
G
V
DD
V
SS
Address
Data Input/Output
Chip Enable
Write Enable
Output Enable
Power
Ground
DEVICE OPERATION
The UT7Q512 has three control inputs called Enable 1 (E), Write
Enable (W), and Output Enable (G); 19 address inputs, A(18:0);
and eight bidirectional data lines, DQ(7:0). The E Device Enable
controls device selection, active, and standby modes. Asserting
E enables the device, causes I
DD
to rise to its active value, and
decodes the 19 address inputs to select one of 524,288 words in
the memory. W controls read and write operations. During a read
cycle, G must be asserted to enable the outputs.
Table 1. Device Operation Truth Table
G
X
1
X
W
X
0
1
1
E
1
0
0
0
I/O Mode
3-state
Data in
3-state
Data out
Mode
Standby
Write
Read
2
Read
A18
A16
A14
A12
A7
A6
A5
A4
V
DD
V
SS
A3
A2
A1
A0
DQ0
DQ1
DQ2
DQ3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
NC
A15
A17
W
A13
A8
A9
A11
V
SS
V
DD
G
A10
E
DQ7
DQ6
DQ5
DQ4
NC
1
0
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
READ CYCLE
A combination of W greater than V
IH
(min), G and E less than
V
IL
(max) defines a read cycle. Read access time is measured
from the latter of Device Enable, Output Enable, or valid address
to valid data output.
SRAM read Cycle 1, the Address Access in figure 3a, is initiated
by a change in address inputs while the chip is enabled with G
asserted and W deasserted. Valid data appears on data outputs
DQ(7:0) after the specified t
AVQV
is satisfied. Outputs remain
active throughout the entire cycle. As long as Device Enable and
Output Enable are active, the address inputs may change at a
rate equal to the minimum read cycle time (t
AVAV
).
SRAM read Cycle 2, the Chip Enable-Controlled Access in
figure 3b, is initiated by E going active while G remains asserted,
W remains deasserted, and the addresses remain stable for the
entire cycle. After the specified t
ETQV
is satisfied, the eight-bit
word addressed by A(18:0) is accessed and appears at the data
outputs DQ(7:0).
SRAM read Cycle 3, the Output Enable-Controlled Access in
figure 3c, is initiated by G going active while E is asserted, W
is deasserted, and the addresses are stable. Read access time is
t
GLQV
unless t
AVQV
or t
ETQV
have not been satisfied.
Figure 2a. UT7Q512 100ns SRAM Shielded
Package Pinout (36)
A18
A16
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
DQ0
DQ1
DQ2
V
SS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
V
DD
A15
A17
W
A13
A8
A9
A11
G
A10
E
DQ7
DQ6
DQ5
DQ4
DQ3
Figure 2b. UT7Q512 100ns SRAM
Package Pinout (32)
2
WRITE CYCLE
A combination of W less than V
IL
(max) and E less than
V
IL
(max) defines a write cycle. The state of G is a “don’t care”
for a write cycle. The outputs are placed in the high-impedance
state when either G is greater than V
IH
(min), or when W is less
than V
IL
(max).
Write Cycle 1, the Write Enable-Controlled Access in figure 4a,
is defined by a write terminated by W going high, with E still
active. The write pulse width is defined by t
WLWH
when the write
is initiated by W, and by t
ETWH
when the write is initiated by E.
Unless the outputs have been previously placed in the high-
impedance state by G, the user must wait t
WLQZ
before applying
data to the nine bidirectional pins DQ(7:0) to avoid bus
contention.
Write Cycle 2, the Chip Enable-Controlled Access in figure 4b,
is defined by a write terminated by the latter of E going inactive.
The write pulse width is defined by t
WLEF
when the write is
initiated by W, and by t
ETEF
when the write is initiated by the E
going active. For the W initiated write, unless the outputs have
been previously placed in the high-impedance state
by G, the user must wait t
WLQZ
before applying data to the eight
bidirectional pins DQ(7:0) to avoid bus contention.
TYPICAL RADIATION HARDNESS
Table 2. Typical Radiation Hardness
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
30
1.5E-7
krad(Si) nominal
Errors/Bit-Day
Notes:
1. The SRAM will not latchup during radiation exposure under recommended
operating conditions.
2. 90% worst case particle environment, Geosynchronous orbit, 100 mils of
Aluminum.
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.5 to 7.0V
-0.5 to 7.0V
-65 to +150°C
1.0W
+150°C
10°C/W
±
10 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
4.5 to 5.5V
-55 to +125°C
0V to V
DD
4
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
(V
DD
= 5.0V±10%) (-55°C to +125°C)
SYMBOL
V
IH
V
IL
V
OL
V
OH
C
IN1
C
IO1
I
IN
I
OZ
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
High-level output voltage
Input capacitance
Bidirectional I/O capacitance
Input leakage current
Three-state output leakage current
I
OL
= 2.1mA,V
DD
=4.5V
I
OH
= -1mA,V
DD
=4.5V
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
V
SS
< V
IN
< V
DD
, V
DD
= V
DD
(max)
0V < V
O
< V
DD
V
DD
= V
DD
(max)
G = V
DD
(max)
0V <V
O
<V
DD
Inputs: V
IL
= V
SS
+ 0.8V,
V
IH
= 2.2V
I
OUT
= 0mA
V
DD
= V
DD
(max)
Inputs: V
IL
= V
SS
+ 0.8V,
V
IH
= 2.2V
I
OUT
= 0mA
V
DD
= V
DD
(max)
Inputs: V
IL
= V
SS
I
OUT
= 0mA
E = V
DD
- 0.5
V
DD
= V
DD
(max)
V
IH
= V
DD
- 0.5V
-55°C and
25°C
+125°C
-2
-2
2.4
10
10
2
2
CONDITION
MIN
2.2
.8
0.4
MAX
UNIT
V
V
V
V
pF
pF
µA
µA
I
OS2, 3
I
DD
(OP)
Short-circuit output current
Supply current operating
@ 1MHz
-80
80
50
mA
mA
I
DD1
(OP)
Supply current operating
@10MHz
100
mA
I
DD2
(SB)
Nominal standby supply current
@0MHz
35
1
µA
mA
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019.
1. Measured only for initial qualification and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
I have a question: Can FPGA be used to detect low-frequency noise? That is, to detect irregular, low-frequency, 10 Hz ~ 1 kHz, and to process and analyze the spectrum and power spectrum? Can the proce...
Insider secrets of the cosmetics industry - L'Oreal's insider's revelations My major in college was French, and by chance I joined L'Oreal (maybe many girls don't know that this is actually the world'...
Microwave power modules ( MPMs ) have been widely used in military applications, including radar systems and electronic warfare (EW) systems, but have rarely been used in communications due to lineari...
[i=s] This post was last edited by stm32f103vct6 on 2018-6-19 09:31 [/i] I found a very strange problem during testing today. The diode I used is shown in the figure:27V voltage flows from pin 1 to pi...
This example program downloads the GPIO TOGGLE in the control SUITEz to the RAM of 28027 through SCI and runs. There are 4 files in the attachment. First, compile the target code in CCS to generate tw...
The core of a machine vision system is image acquisition and processing. All information comes from images, and image quality is crucial to the entire vision system. A good image can improve the st...[Details]
The intelligent driving community has its own rhythm. Some are busy pushing new versions and focusing on R&D, others are busy with publicity and promotion, and still others are immersed in mass pro...[Details]
A line scan lens is an industrial lens used with line scan cameras. Its imaging principle is to capture the image of the workpiece using a linear sensor and then perform digital signal processing t...[Details]
To enable real-time monitoring of home security and automatically dial a number for voice prompts or send text messages when an alarm occurs, a GPRS-based embedded telephone alarm system was design...[Details]
New energy vehicles are increasingly popular with consumers due to policies and energy conservation. Once you've purchased your vehicle, maintenance is essential. However, due to the different powe...[Details]
As the main model among new energy vehicles, pure electric vehicles have received strong support and encouragement from the country in recent years, and their development is changing with each pass...[Details]
Amidst the wave of intelligent automotive transformation, advanced driver assistance is gradually emerging from cutting-edge technology into the mainstream, becoming a new frontier of industry comp...[Details]
Core point: The automotive industry chain and the humanoid robot industry have collaborative advantages in hardware, software, and scenarios. Upstream and downstream companies in the automotive ind...[Details]
Recently, AstroBo Robot, a subsidiary of Chenxing Automation, launched a new mobile collaborative palletizing product. Leveraging an omnidirectional mobile chassis, an intelligent scheduling system...[Details]
introduction
As “energy conservation and emission reduction” has become an indicator of the National Economic Development Outline of the 11th Five-Year Plan, people’s awareness of green enviro...[Details]
The digital TV set-top box consists of a tuner, QAM demodulator, TS demultiplexer, MPEG-2 decoder, PAUNTSC video encoder, embedded CPU system and peripheral interfaces, CA module, and uplink data m...[Details]
In the scorching summer, electric fans are a must-have for cooling down people's homes. However, I believe most people have encountered this situation: the fan is plugged in, the switch is pressed,...[Details]
Pure electric vehicles, structurally speaking, have components such as a power battery. In addition to the power battery, a small battery also powers some low-voltage electrical components and even...[Details]
With the advent of the electric car era, the number of pure electric vehicles has increased significantly, but many car owners do not know how to properly maintain pure electric vehicles. In additi...[Details]
Permanent magnets are essential components in a wide range of household and industrial devices. They are particularly crucial in the renewable energy sector, including electric vehicle motors. Curr...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
