EEWORLDEEWORLDEEWORLD

Part Number

Search

50930-1080E

Description
Board Connector, 240 Contact(s), 3 Row(s), Female, Right Angle, Solder Terminal, Receptacle,
CategoryThe connector    The connector   
File Size60KB,2 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

50930-1080E Overview

Board Connector, 240 Contact(s), 3 Row(s), Female, Right Angle, Solder Terminal, Receptacle,

50930-1080E Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid2143722442
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL9.1
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (30)
Contact completed and terminatedTIN LEAD
Contact point genderFEMALE
Contact materialBERYLLIUM COPPER
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee0
MIL complianceNO
Manufacturer's serial number50930
Mixed contactsNO
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of rows loaded3
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts240
CPLD generates pulse width adjustable PWM signal
Dear experts, I used Altera's EPM240 to make a PWM output. The project requirements are: the pulse width is adjustable from 10ns to 100ns, the amplitude is 3.3, the frequency is 100k, and the rise tim...
dongxu_LCC FPGA/CPLD
A mistake about Weifu
ORG 0000H SJMP MAIN MAIN:MOV P1,#FFH .5 ACALL DE05 CLR P1.5 CPL P3.0 REL1:JB P1.2,REL2 SETB P1.6 ACALL DE05 CLR P1.6 CPL P3.0 REL2:JB P1.3,REL3 SETB P1.7 ACALL DE05 CLR P1.7 CPL P3.0 REL3:MOV A,P1 ORL...
microchenhard Embedded System
The built-in sweep generation capability of the Series 2600A SourceMeter instrument enables faster throughput and precise timing control
The setup run time is to configure the SMU source and measure [1] parameters before performing the sweep . Therefore, the setup interval only needs to be run once. From there, the sweep can be run as ...
Jack_ma Test/Measurement
Agilent E3632A Repair
When the power is on and the load is not applied, I adjusted the voltage knob. When it reached 8V, I found that there was a burning smell and the area marked CR37 was black. Can someone tell me what i...
寒夜星辰 Power technology
Question + Why won't the program reset when it's running?
When the program does not enter LPM3 mode, when monitoring through the serial port.....
accboy TI Technology Forum
The core board cannot start UBOOT from NOR
The core board I just bought cannot boot from NOR. UBOOT has been burned in NOR. It can be normally booted from NOR on the development board. My board and the development board have the same reset cir...
zeng2730 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 208  2675  472  2053  1649  5  54  10  42  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号