(G); 19 address inputs, A(18:0); and eight bidirectional data
lines, DQ(7:0). E1 and E2 device enables control device
selection, active, and standby modes. Asserting E1 and E2
enables the device, causes I
DD
to rise to its active value, and
decodes the 19 address inputs to select one of 524,288 words in
the memory. W controls read and write operations. During a read
cycle, G must be asserted to enable the outputs.
Table 1. Device Operation Truth Table
G
X
W
X
X
0
1
1
E2
X
0
1
1
1
E1
1
X
0
0
0
I/O Mode
3-state
3-state
Data in
3-state
Data out
Mode
Standby
Standby
Write
Read
2
Read
Figure 2. 15ns SRAM Pinout (36)
X
X
1
PIN NAMES
A(18:0)
DQ(7:0)
E1
E2
Address
Data Input/Output
Chip Enable 1
(active low)
Chip Enable 2
(active high)
W
G
WriteEnable
Output Enable
0
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
READ CYCLE
A combination of W and E2 greater than V
IH
(min) and E1 less
than V
IL
(max) defines a read cycle. Read access time is
measured from the latter of chip enable, output enable, or valid
address to valid data output.
SRAM Read Cycle 1, the Address Access in Figure 3a, is
initiated by a change in address inputs while the chip is enabled
with G asserted and W deasserted. Valid data appears on data
outputs DQ(7:0) after the specified t
AVQV
is satisfied. Outputs
remain active throughout the entire cycle. As long as chip enable
and output enable are active, the address inputs may change at
a rate equal to the minimum read cycle time (t
AVAV
).
SRAM Read Cycle 2, the Chip Enable-controlled Access in
Figure 3b, is initiated by E1 and E2 going active while G remains
asserted, W remains deasserted, and the addresses remain stable
for the entire cycle. After the specified t
ETQV
is satisfied, the
eight-bit word addressed by A(18:0) is accessed and appears at
the data outputs DQ(7:0).
SRAM Read Cycle 3, the Output Enable-controlled Access in
Figure 3c, is initiated by G going active while E1 and E2 are
asserted, W is deasserted, and the addresses are stable. Read
access time is t
GLQV
unless t
AVQV
or t
ETQV
have not been
satisfied.
V
DD1
Power (1.8V)
V
DD2
Power (3.3V)
V
SS
Ground
2
WRITE CYCLE
A combination of W and E1 less than V
IL
(max) and E2 greater
than V
IH
(min) defines a write cycle. The state of G is a “don’t
care” for a write cycle. The outputs are placed in the high-
impedance state when either G is greater than V
IH
(min), or
when W is less than V
IL
(max).
Write Cycle 1, the Write Enable-controlled Access in Figure
4a, is defined by a write terminated by W going high, with E1
and E2 still active. The write pulse width is defined by t
WLWH
when the write is initiated by W, and by t
ETWH
when the write
is initiated by E1 or E2. Unless the outputs have been
previously placed in the high-impedance state by G, the user
must wait t
WLQZ
before applying data to the nine bidirectional
pins DQ(7:0) to avoid bus contention.
Write Cycle 2, the Chip Enable-controlled Access in Figure
4b, is defined by a write terminated by either of E1 or E2 going
inactive. The write pulse width is defined by t
WLEF
when the
write is initiated by W, and by t
ETEF
when the write is initiated
by either E1or E2 going active. For the W initiated write, unless
the outputs have been previously placed in the high-impedance
state by G, the user must wait t
WLQZ
before applying data to
the eight bidirectional pins DQ(7:0) to avoid bus contention.
OPERATIONAL ENVIRONMENT
The UT8R512K8 SRAM incorporates special design and
layout features which allows operation in a limited
environment.
Table 2. Operational Environment
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
Notes:
1. The SRAM is immune to latchup to particles >100MeV-cm
2
/mg.
2. 90% worst case particle environment, Geosynchronous orbit, 100 mils of
Aluminum.
300K
8.9x10
-10
rad(Si)
Errors/Bit-Day
Supply Sequencing
No supply voltage sequencing is required between V
DD1
and
V
DD2
.
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD1
V
DD2
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.3 to 2.1V
-0.3 to 3.8V
-0.3 to 3.8V
-65 to +150°C
1.2W
+150°C
5°C/W
±
5 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD1
V
DD2
T
C
PARAMETER
Positive supply voltage
Positive supply voltage
Case temperature range
LIMITS
1.7 to 1.9V
1
3.0 to 3.6V
(P) Screening: -25°C
(C) Screening: -55 to +125°C
(W) Screening: -40 to +125°C
0V to V
DD2
V
IN
Notes:
DC input voltage
1. For increased noise immunity, supply voltage (V
DD1
) can be increased to 2.0V. If not tested, all applicable DC and AC charateristics are guaranteed by characterization
at V
DD1
(max) = 2.0V.
4
DC ELECTRICAL CHARACTERISTICS (Pre and Post-Radiation)*
Unless otherwise noted, Tc is per the temperature ordered
I am a beginner in embedded development and I am using evc4.0+evc4.0 sp4. When I run an example program, the following error message appears: "An Application targeting a standard SDK for windows CE .N...
Today I contacted Xiaotian who is in charge of schematics and wiring. Haha, this kid is in a different position every time I contact him. He is busy enough during this period. I am urging him to draw ...
The function is similar to a countdown stopwatch, with four independent buttons controlling the four-digit digital tube display; s1 controls the adjustable digital tube display, and when s2=1, 2, 3, a...
TPMS is the abbreviation of "Tire Pressure Monitoring System". It is mainly used to automatically monitor the tire pressure in real time when the car is driving, and to alarm for tire leakage and low ...
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
introduction
my country has a vast territory and a large population. The scale of housing construction is huge, and the amount of residential construction is large and wide. It is still on t...[Details]
1 Introduction
A wide variety of communication cables and control cables are widely used in various instruments and control equipment. Whether the cable is well-conducted and
whether
th...[Details]
1. Introduction
This design was made for participating in an electronic design competition. It effectively solved the problem of the operation and control of an electric car on a seesaw. The s...[Details]
With the advent of increasingly powerful processors, image sensors, memory, and other semiconductor devices, as well as the algorithms that enable them, computer vision can be implemented in a wide...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
MediaTek (2454) announced the acquisition of F-MStar (3697) and attracted the attention of IC design industry. This morning, Gartner Semiconductor Industry Research Director Hong Cenwei analyzed ...[Details]
VP2188 is a color STN LCD module produced by Jingdian Pengyuan. This module is a dot matrix transmissive color STN display screen with a color scale of 65 k colors and white LED backlight. Its core...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
OC faults may be the most frequent and the most frequent of all faults in the inverter. They alarm during the startup process, during the shutdown process, during operation, and even when powered o...[Details]
As people's requirements for safety and comfort in the process of driving cars continue to increase, automotive radars are widely used in the car's adaptive cruise system, collision avoidance syste...[Details]
Preface
In recent years, white light LEDs have gradually replaced incandescent bulbs and fluorescent lamps because they have unparalleled advantages over traditional light sources in terms...[Details]
Introduction
X1226 has the functions of clock and calendar. The clock relies on hour, minute and second registers to track, and the calendar relies on date, week, month and year registers to tr...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
