(G); 19 address inputs, A(18:0); and eight bidirectional data
lines, DQ(7:0). E1 and E2 device enables control device
selection, active, and standby modes. Asserting E1 and E2
enables the device, causes I
DD
to rise to its active value, and
decodes the 19 address inputs to select one of 524,288 words in
the memory. W controls read and write operations. During a read
cycle, G must be asserted to enable the outputs.
Table 1. Device Operation Truth Table
G
X
W
X
X
0
1
1
E2
X
0
1
1
1
E1
1
X
0
0
0
I/O Mode
3-state
3-state
Data in
3-state
Data out
Mode
Standby
Standby
Write
Read
2
Read
Figure 2. 15ns SRAM Pinout (36)
X
X
1
PIN NAMES
A(18:0)
DQ(7:0)
E1
E2
Address
Data Input/Output
Chip Enable 1
(active low)
Chip Enable 2
(active high)
W
G
WriteEnable
Output Enable
0
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
READ CYCLE
A combination of W and E2 greater than V
IH
(min) and E1 less
than V
IL
(max) defines a read cycle. Read access time is
measured from the latter of chip enable, output enable, or valid
address to valid data output.
SRAM Read Cycle 1, the Address Access in Figure 3a, is
initiated by a change in address inputs while the chip is enabled
with G asserted and W deasserted. Valid data appears on data
outputs DQ(7:0) after the specified t
AVQV
is satisfied. Outputs
remain active throughout the entire cycle. As long as chip enable
and output enable are active, the address inputs may change at
a rate equal to the minimum read cycle time (t
AVAV
).
SRAM Read Cycle 2, the Chip Enable-controlled Access in
Figure 3b, is initiated by E1 and E2 going active while G remains
asserted, W remains deasserted, and the addresses remain stable
for the entire cycle. After the specified t
ETQV
is satisfied, the
eight-bit word addressed by A(18:0) is accessed and appears at
the data outputs DQ(7:0).
SRAM Read Cycle 3, the Output Enable-controlled Access in
Figure 3c, is initiated by G going active while E1 and E2 are
asserted, W is deasserted, and the addresses are stable. Read
access time is t
GLQV
unless t
AVQV
or t
ETQV
have not been
satisfied.
V
DD1
Power (1.8V)
V
DD2
Power (3.3V)
V
SS
Ground
2
WRITE CYCLE
A combination of W and E1 less than V
IL
(max) and E2 greater
than V
IH
(min) defines a write cycle. The state of G is a “don’t
care” for a write cycle. The outputs are placed in the high-
impedance state when either G is greater than V
IH
(min), or
when W is less than V
IL
(max).
Write Cycle 1, the Write Enable-controlled Access in Figure
4a, is defined by a write terminated by W going high, with E1
and E2 still active. The write pulse width is defined by t
WLWH
when the write is initiated by W, and by t
ETWH
when the write
is initiated by E1 or E2. Unless the outputs have been
previously placed in the high-impedance state by G, the user
must wait t
WLQZ
before applying data to the nine bidirectional
pins DQ(7:0) to avoid bus contention.
Write Cycle 2, the Chip Enable-controlled Access in Figure
4b, is defined by a write terminated by either of E1 or E2 going
inactive. The write pulse width is defined by t
WLEF
when the
write is initiated by W, and by t
ETEF
when the write is initiated
by either E1or E2 going active. For the W initiated write, unless
the outputs have been previously placed in the high-impedance
state by G, the user must wait t
WLQZ
before applying data to
the eight bidirectional pins DQ(7:0) to avoid bus contention.
OPERATIONAL ENVIRONMENT
The UT8R512K8 SRAM incorporates special design and
layout features which allows operation in a limited
environment.
Table 2. Operational Environment
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
Notes:
1. The SRAM is immune to latchup to particles >100MeV-cm
2
/mg.
2. 90% worst case particle environment, Geosynchronous orbit, 100 mils of
Aluminum.
300K
8.9x10
-10
rad(Si)
Errors/Bit-Day
Supply Sequencing
No supply voltage sequencing is required between V
DD1
and
V
DD2
.
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD1
V
DD2
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.3 to 2.1V
-0.3 to 3.8V
-0.3 to 3.8V
-65 to +150°C
1.2W
+150°C
5°C/W
±
5 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD1
V
DD2
T
C
PARAMETER
Positive supply voltage
Positive supply voltage
Case temperature range
LIMITS
1.7 to 1.9V
1
3.0 to 3.6V
(P) Screening: -25°C
(C) Screening: -55 to +125°C
(W) Screening: -40 to +125°C
0V to V
DD2
V
IN
Notes:
DC input voltage
1. For increased noise immunity, supply voltage (V
DD1
) can be increased to 2.0V. If not tested, all applicable DC and AC charateristics are guaranteed by characterization
at V
DD1
(max) = 2.0V.
4
DC ELECTRICAL CHARACTERISTICS (Pre and Post-Radiation)*
Unless otherwise noted, Tc is per the temperature ordered
I made an edit box under the dialog box. Because the edit box is relatively large, the original word output is relatively small. I don’t want to change the size of the edit box. I want to know how to ...
In the global energy-saving car competition Shell Eco-Marathon, hundreds of student teams compete every year with their self-developed energy-saving cars. They do not race, but challenge to complete t...
Has anyone used the LaunchPad debug interface to connect directly to their own board? I was going to do it last time, but then I didn't do it because of the board area and wiring. But there is no grou...
Two different LEDs, the anode is connected to +5V, and the cathode is connected to the I/O port. If you want the brightness to be the same when they are lit, is it better to connect them in series or ...
I use AT commands to send commands to the module through the computer serial port, but it has not been successful. I don’t know why? The baud rate is 115200. I send the following commands: 1. Send: at...
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
Toyohashi University of Technology demonstrated electric field coupled wireless power supply technology using life-size car tires and roads at the wireless technology exhibition "Wireless Technolog...[Details]
1 Introduction
There have been many studies on the detection and protection of power grid short circuit and line fault. The short circuit, overload and overvoltage protectors on the market have ...[Details]
Single-chip microcomputers are widely used because of their small size, powerful functions and low price. This article introduces the method of designing a micro electronic piano using the AT89C51 sin...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
1. When the slip speed regulating motor is undergoing frequency conversion and energy saving transformation, the original excitation box (referred to as the speed regulating box) and the original s...[Details]
With the rapid development of the national economy, lifting and hoisting operations are used more and more frequently and widely in various fields of economic construction. China has continuously expl...[Details]
1 What is an LED floodlight?
LED downlights are also called spotlights, projection lamps, and spotlights. They are mainly used for architectural decorative lighting and commercial space lighti...[Details]
1 Overview
In the field of traditional lighting, the concepts and definitions of lamps and lamps are clear. Lamps and lamps have their own applicable product standards, supporting technical st...[Details]
summary
This article will briefly analyze the success and shortcomings of high-frequency DC-DC switching power supplies in the process of miniaturization (the second basic goal), and propose m...[Details]
The installation locations of DC-DC converters are relatively scattered. DC-DC converters can be found on the power board, main board, logic control board and other circuit boards of PDP color TVs....[Details]
IntroductionLED
billboards are a kind of information display terminal for the public, which has a wide range of civil and commercial values. However, the information displayed on most LED bil...[Details]
The Challenge:
Improving Siemens Wind
Turbine Controls
System software automated testing for regular releases, validating wind turbine control system components during the developme...[Details]
introduction
This paper mainly studies the problem of voltage sag control. For sensitive load equipment with rectifier inverter structure, this paper proposes a DC dynamic voltage restorer (Dy...[Details]
With the reform of the education system, the proportion of funds invested in teaching facilities by colleges and universities has become increasingly important. As the most basic hardware condition fo...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
