(G); 19 address inputs, A(18:0); and eight bidirectional data
lines, DQ(7:0). E1 and E2 device enables control device
selection, active, and standby modes. Asserting E1 and E2
enables the device, causes I
DD
to rise to its active value, and
decodes the 19 address inputs to select one of 524,288 words in
the memory. W controls read and write operations. During a read
cycle, G must be asserted to enable the outputs.
Table 1. Device Operation Truth Table
G
X
W
X
X
0
1
1
E2
X
0
1
1
1
E1
1
X
0
0
0
I/O Mode
3-state
3-state
Data in
3-state
Data out
Mode
Standby
Standby
Write
Read
2
Read
Figure 2. 15ns SRAM Pinout (36)
X
X
1
PIN NAMES
A(18:0)
DQ(7:0)
E1
E2
Address
Data Input/Output
Chip Enable 1
(active low)
Chip Enable 2
(active high)
W
G
WriteEnable
Output Enable
0
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
READ CYCLE
A combination of W and E2 greater than V
IH
(min) and E1 less
than V
IL
(max) defines a read cycle. Read access time is
measured from the latter of chip enable, output enable, or valid
address to valid data output.
SRAM Read Cycle 1, the Address Access in Figure 3a, is
initiated by a change in address inputs while the chip is enabled
with G asserted and W deasserted. Valid data appears on data
outputs DQ(7:0) after the specified t
AVQV
is satisfied. Outputs
remain active throughout the entire cycle. As long as chip enable
and output enable are active, the address inputs may change at
a rate equal to the minimum read cycle time (t
AVAV
).
SRAM Read Cycle 2, the Chip Enable-controlled Access in
Figure 3b, is initiated by E1 and E2 going active while G remains
asserted, W remains deasserted, and the addresses remain stable
for the entire cycle. After the specified t
ETQV
is satisfied, the
eight-bit word addressed by A(18:0) is accessed and appears at
the data outputs DQ(7:0).
SRAM Read Cycle 3, the Output Enable-controlled Access in
Figure 3c, is initiated by G going active while E1 and E2 are
asserted, W is deasserted, and the addresses are stable. Read
access time is t
GLQV
unless t
AVQV
or t
ETQV
have not been
satisfied.
V
DD1
Power (1.8V)
V
DD2
Power (3.3V)
V
SS
Ground
2
WRITE CYCLE
A combination of W and E1 less than V
IL
(max) and E2 greater
than V
IH
(min) defines a write cycle. The state of G is a “don’t
care” for a write cycle. The outputs are placed in the high-
impedance state when either G is greater than V
IH
(min), or
when W is less than V
IL
(max).
Write Cycle 1, the Write Enable-controlled Access in Figure
4a, is defined by a write terminated by W going high, with E1
and E2 still active. The write pulse width is defined by t
WLWH
when the write is initiated by W, and by t
ETWH
when the write
is initiated by E1 or E2. Unless the outputs have been
previously placed in the high-impedance state by G, the user
must wait t
WLQZ
before applying data to the nine bidirectional
pins DQ(7:0) to avoid bus contention.
Write Cycle 2, the Chip Enable-controlled Access in Figure
4b, is defined by a write terminated by either of E1 or E2 going
inactive. The write pulse width is defined by t
WLEF
when the
write is initiated by W, and by t
ETEF
when the write is initiated
by either E1or E2 going active. For the W initiated write, unless
the outputs have been previously placed in the high-impedance
state by G, the user must wait t
WLQZ
before applying data to
the eight bidirectional pins DQ(7:0) to avoid bus contention.
OPERATIONAL ENVIRONMENT
The UT8R512K8 SRAM incorporates special design and
layout features which allows operation in a limited
environment.
Table 2. Operational Environment
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
Notes:
1. The SRAM is immune to latchup to particles >100MeV-cm
2
/mg.
2. 90% worst case particle environment, Geosynchronous orbit, 100 mils of
Aluminum.
300K
8.9x10
-10
rad(Si)
Errors/Bit-Day
Supply Sequencing
No supply voltage sequencing is required between V
DD1
and
V
DD2
.
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD1
V
DD2
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.3 to 2.1V
-0.3 to 3.8V
-0.3 to 3.8V
-65 to +150°C
1.2W
+150°C
5°C/W
±
5 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD1
V
DD2
T
C
PARAMETER
Positive supply voltage
Positive supply voltage
Case temperature range
LIMITS
1.7 to 1.9V
1
3.0 to 3.6V
(P) Screening: -25°C
(C) Screening: -55 to +125°C
(W) Screening: -40 to +125°C
0V to V
DD2
V
IN
Notes:
DC input voltage
1. For increased noise immunity, supply voltage (V
DD1
) can be increased to 2.0V. If not tested, all applicable DC and AC charateristics are guaranteed by characterization
at V
DD1
(max) = 2.0V.
4
DC ELECTRICAL CHARACTERISTICS (Pre and Post-Radiation)*
Unless otherwise noted, Tc is per the temperature ordered
1. The board itself has a CMOS camera interface with a driver. It can be used now, but the distance is short. 2. The board has a USB interface. I wanted to use a USB camera, but found that the distanc...
[p=26, null, left][color=#362e2b][font=Arial] TMS320F28335 is a Harvard structure DSP. Logically, it has 4M×16-bit program space and 4M×16-bit data space, but physically, the program space and data sp...
1. The First Law (An object will remain in its original state unless acted upon by an external force)
Corollary: When you don’t pursue a beautiful girl, she will just stay there. Comment: This is o...
The default is//// Define a region for the on-chip flash.//define region FLASH = mem:[from 0x00000000 to 0x0003ffff]; When I changed the above region to mem:[from 0x00001000 to 0x0003ffff], the progra...
Under the design trend of SOC, reusable SIP is the key to the rapid development of a complex chip. Using SIP can speed up the launch of IC products, shorten the gap between IC process technology progr...
As the Internet of Things, technology convergence, voice control, and more continue to advance, device capabilities are becoming more advanced, but with that comes increasing pressure on test teams. W...
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
With the rapid development of science and technology, especially the widespread application of digital technology and various ultra-large-scale integrated circuits, electronic equipment, especially...[Details]
1 Introduction
A wide variety of communication cables and control cables are widely used in various instruments and control equipment. Whether the cable is well-conducted and
whether
th...[Details]
Google's driverless technology is not only an eye-catching technology, but also a subversion of the car usage model.
Those who have watched anti-terrorism films and TV dramas must have been im...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
Overview
As a remote network communication control method with advanced technology, high reliability, complete functions and reasonable cost, CAN-bus has been widely used in various automa...[Details]
MediaTek (2454) announced the acquisition of F-MStar (3697) and attracted the attention of IC design industry. This morning, Gartner Semiconductor Industry Research Director Hong Cenwei analyzed ...[Details]
introduction
MAX6636 is a multi-channel precision temperature monitor that can not only monitor local temperature, but also connect up to 6 diodes externally. Each channel has a programmable...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
