EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-FLPSC3042

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-FLPSC3042 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), SC/UPC Connector,

PH1-FLPSC3042 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Emitter/Detector TypePIN PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1537 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-17 dBm
Base Number Matches1
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
F7-Air Conditioning Wizard Progress Post-01
[i=s]This post was last edited by cedar_xuesong on 2015-10-15 09:13[/i] Project: Air Conditioning WizardProject Introduction: Please refer to https://bbs.eeworld.com.cn/thread-472487-1-1.htmlCurrent P...
cedar_xuesong stm32/stm8
High-power LED drive circuit (AC-DC) design example (very practical and specific)
High-power LED drive circuit (AC-DC) design example (very practical and specific), mainly does not require a transformer; directly connected to the AC power supply. Interested friends can take a look...
tonytong Power technology
CB314 program cannot be burned in ~ solution
The program cannot be burned in, what should I pay attention to? [/color][/size] [size=5][color=#ff8c00]2.1_System_Linux-3.0.35 -> 04_Burn Tool, the burn tool in the path just now is relatively simila...
明远智睿Lan ARM Technology
How to deal with the new national standard for electric vehicles? TI provides BMS solutions!
[i=s]This post was last edited by qwqwqw2088 on 2019-11-20 08:35[/i]According to the national standard management procedures, the mandatory national standard "Safety Technical Specifications for Elect...
qwqwqw2088 Analogue and Mixed Signal
I want to make an instrument, but the range selection IO takes up too many places, what should I do?
I want to make an instrument, but the range selection IO takes up too much space. What should I do? For example, thisHow do I choose the gear I sense? For example, if it is 1k gear, I should let AD kn...
cl17726 Microcontroller MCU
There is no armv4i option in EVC, why?
I just started to develop applications for Windows CE. I found that I fully installed EVC4.0+SP4, platform winCE5.0, s3c2410. I need to select arm4i, but there is no ARMv4I in the cpu platform selecti...
fishingnet001 ARM Technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 935  2737  1519  919  589  19  56  31  12  22 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号