EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-7LPLA2561

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-7LPLA2561 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,

PH1-7LPLA2561 Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Connection TypeLC/SPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Emitter/Detector TypePIN PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1528 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-17 dBm
Base Number Matches1
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
How to use C language to implement the communication protocol RS232 between the microcontroller and MC45 (GPRS module)
As the title says, my project is to connect PIC microcontroller with MC45 to send and receive text messages. Now I know the RS232 protocol standard, but I don't know how to implement it in C language....
yutingchenghong Programming Basics
How can I wire this circuit to minimize interference?
[i=s]This post was last edited by littleshrimp on 2020-2-16 13:09[/i]Assume there is a microphone on the left In the middle is a 2-core shielded cable, the black wire is the shielding wire The amplifi...
littleshrimp Analog electronics
【TI original】Radio implementation based on LM3S811 and TEA5767 chips
The radio module used is Philips TEA5767. I searched the Internet for related content and found that many people are asking about it, but few provide programming guidance. Maybe experts are too lazy t...
梦之旅 Microcontroller MCU
R&D? Copy board?
I am planning to make a product and have discussed with several R&D personnel. The R&D cost is a bit high and the cycle is relatively long. Now I am thinking of copying the board and cracking the prog...
Telefon MCU
[Help] I need help drawing a simple PCB board.
[i=s]This post was last edited by upc_arm on 2022-2-7 10:59[/i]RT: Found it, thank you....
upc_arm Buy&Sell
[RVB2601 Creative Application Development] + Stickman Player
[i=s]This post was last edited by tobot on 2022-6-9 10:08[/i]Stickman Player Project Background Originally, I wanted to use the voice function of RVB-2601 to make a price sign that can automatically q...
tobot XuanTie RISC-V Activity Zone

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2327  2293  2461  2665  2066  47  50  54  42  36 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号