2222 809 07...
Vishay BCcomponents
Film Dielectric Trimmers
FEATURES
•
High temperature type
•
Housing dimensions:
11 mm x 14 mm x 9 mm
•
For a basic grid of 2.54 mm
•
Top adjustment
•
Vertical version
TEST VOLTAGE (DC) FOR 1 MINUTE:
400 V
MAXIMUM CONTACT RESISTANCE:
5 mΩ
APPLICATIONS
•
For fine adjustment in professional applications
MINIMUM INSULATION RESISTANCE BETWEEN
STATOR AND ROTOR:
10 000 MΩ
DESCRIPTION:
The trimmers consist of a glass reinforced polysulphone
frame with a polysulphone dust cover, brass rotor and stator
with PTFE or polycarbonate film as the dielectric. The stator
plates are stacked on pins and separated by rings, so that it
is possible to produce a single stator or a differential type.
The rotor contact surfaces are plated to ensure a long life
and a stable contact even under severe climatic conditions.
CATEGORY TEMPERATURE RANGE:
-40 to +125 °C
CLIMATIC CATEGORY (IEC 60068):
40/125/21
QUALITY LEVEL:
Sampling and data evaluation for quality level in accordance
with
“MIL-STD-105D”
and
“IEC 60410”:
<0.15% major defects
<0.65% minor defects
Each capacitor is tested for minimum C
max
and is also
subjected to the full test voltage.
MINIMUM STORAGE TEMPERATURE:
-55 °C
RELATED SPECIFICATION:
IEC 60418-1 and 4
C
min
/ C
max
:
SINGLE STATOR TYPE
2.5/20 to 7/100 pF
EFFECTIVE ANGLE OF ROTATION:
180°
DIFFERENTIAL TYPE
2/12 to 7/150 pF
OPERATING TORQUE:
1.5 to 25 mNm
RATED VOLTAGE (DC):
200 V
MAXIMUM AXIAL THRUST:
2N
Document Number 28530
Revision: 10-Nov-04
For technical questions contact: filmcaps.roeselare@vishay.com
www.vishay.com
329
2222 809 07...
Vishay BCcomponents
Film Dielectric Trimmers
0.8
±0.1
(2×)
14
0
−0.2
10.16
±0.2
5.8
±0.1
0.6
+0.1
0
(2×)
0.5
±0.1
(2×)
0.8
±0.1
(2×)
3.6
±0.2
0.5
±0.1
(2×)
marking
7.62
±
0.2
11.5
0
−
0.3
8.6 max.
9.2
±0.4
4
±0.5
depth of
slot = 0.6
0.6
±0.05
3.81
S
handbook, halfpage
2.54
R
R
1.3
(4×)
S
R = rotor, S = stator
Trimmers 2222 809 07... series.
Dimensions in millimeters.
ADJUSTMENT:
The trimmers can be adjusted with a screwdriver or trimming
key. Capacitance increase is obtained with clockwise rotation
MARKING:
The trimmers are marked with the capacitance value in pF,
followed by the letter ‘E’ (single-stator type) or the letter ‘D’
(differential type)
.
MOUNTING:
The trimmer can be mounted on printed-circuit boards with a
grid of 2.54 mm and a minimum hole diameter of 1.25 mm
.
PACKAGING:
Blister packs of 70 units each. For smallest packaging
quantity (SPQ) see Electrical Data Table.
ORDERING INFORMATION
C
min
/C
max
(pF)
2/12
2.5/20
4/40
5/60
6/80
7/100
7/150
CATALOG NUMBER 2222 809 07...
TOP AND BOTTOM ADJUSTMENT
SINGLE STATOR TYPE
-
004
008
011
013
015
-
DIFFERENTIAL TYPE
018
006
009
012
014
016
107
www.vishay.com
330
For technical questions contact: filmcaps.roeselare@vishay.com
Document Number 28530
Revision: 10-Nov-04
2222 809 07...
Film Dielectric Trimmers
Vishay BCcomponents
ELECTRICAL DATA
GUARANTEED
MAX. C
min
/
MIN. C
max
AT 200 kHz
(pF)
2/12
2.5/20
TAN
δ
AT
C
max
×
10
−4
TYPE
DIEL.
1 MHz
differential
single stator
differential
single stator
differential
single stator
differential
single stator
differential
single stator
differential
differential
PTFE
(1)
PTFE
≤
10
≤
10
≤
10
≤
10
≤
10
≤
10
≤
50
100 MHz
≤
17
≤
17
≤
17
≤
25
≤
25
≤
25
-
TEMP.
COEFF.
(3)
(10
−6
/K)
0 ± 200
0 ± 200
SPQ
CATALOG
NUMBER
350
350
350
2222 809 07018
2222 809 07004
2222 809 07006
2222 809 07008
2222 809 07009
2222 809 07011
2222 809 07012
2222 809 07013
2222 809 07014
2222 809 07015
2222 809 07016
2222 809 07107
0 ± 200
4/40
PTFE
350
350
0 ± 200
5/60
PTFE
350
350
0 ± 200
6/80
PTFE
350
350
0 ± 200
7/100
7/150
Notes
PTFE
PC
(2)
350
350
0 ± 200
350
1. PTFE = polytetrafluorethylene.
2. PC = polycarbonate.
3. C: 60% to 80% of C
max
; T
amb
: from +20 °C to +125 °C.
TEST PROCEDURES AND REQUIREMENTS
IEC
60418-1
CLAUSE
4.2
14
19
21
21.1
21.2
22
Ua
Ub
Na
IEC 60068
TEST
METHOD
TEST
method of mounting
capacitance drift
thrust
robustness of terminations:
tensile
bending
rapid change of temperature
1 cycle; 0.5 hours at lower and 0.5
hours at upper category
temperature
23
T
Ta
Tb
24
25
Eb
Fc
soldering:
solderability
resistance to heat
impact bump
vibration
solder bath immersion 3 mm;
235 °C; 2 s
solder bath: 260 °C; 10 s
4000 ± 10 bumps; 40 g; 6 ms
frequency 10 to 55 Hz;
amplitude 0.35 mm;
1.5 hours
good wetting
no mechanical damage
no mechanical damage
∆C/C: ≤
0.2%;
no mechanical damage
∆C/C: ≤
0.25%;
no mechanical damage
1N
no damage
bending not allowed
∆C/C: ≤
1%
method A
after TC measurement
axial thrust of 2 N
∆C/C: ≤
1%
∆C/C: ≤
0.3%
PROCEDURE
REQUIREMENTS
Document Number 28530
Revision 10-Nov-04
For technical questions contact: filmcaps.roeselare@vishay.com
www.vishay.com
331
2222 809 07...
Vishay BCcomponents
IEC
60418-1
CLAUSE
26
26.1
B
IEC 60068
TEST
METHOD
dry heat
Film Dielectric Trimmers
TEST
climatic sequence:
PROCEDURE
∆C/C: ≤
3
16 hours at upper category
temperature
REQUIREMENTS
tan
δ: ≤
10 x 10
-4
R
ins
:
≥
10000 M
Ω
;
rotor contact R:
≤
10 m
Ω
voltage proof:
400 V for 1 minute
visual examination:
no mechanical damage
operating torque:
1.5 to 35 mNm
∆C/C: ≤
3%
tan
δ: ≤
10 x 10
-4
R
ins
:
≥
10000 M
Ω
;
rotor contact R:
≤
10 m
Ω
voltage proof:
400 V for 1 minute
visual examination:
no mechanical damage
operating torque:
1.5 to 35 mNm
26.2
26.3
26.5
27
D
Aa
damp heat accelerated,
first cycle
cold
damp heat accelerated,
remaining cycles
1 cycle; 24 hours; +40 °C;
95 to 100% RH
16 hours; -40 °C
1 cycle; 24 hours; +40 °C;
95 to 100% RH
21 days; +40 °C;
90 to 95% RH
Ca
damp heat steady state
29
mechanical endurance
25 cycles
∆C/C: ≤
0.3%
∆C/C
after axial thrust:
≤
0.3%;
rotor contact R:
≤
10 m
Ω
voltage proof:
400 V for 1 minute
visual examination:
no mechanical damage
operating torque:
1 to 50 mNm
www.vishay.com
332
For technical questions contact: filmcaps.roeselare@vishay.com
Document Number 28530
Revision: 10-Nov-04
Legal Disclaimer Notice
Vishay
Notice
Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc.,
or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies.
Information contained herein is intended to provide a product description only. No license, express or implied, by
estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's
terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express
or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness
for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications.
Customers using or selling these products for use in such applications do so at their own risk and agree to fully
indemnify Vishay for any damages resulting from such improper use or sale.
Document Number: 91000
Revision: 08-Apr-05
www.vishay.com
1
京公网安备 11010802033920号
EEWORLD
