EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-TI2FA368N

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-TI2FA368N Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,

PH1-TI2FA368N Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Communication standardsGR-253
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1550 nm
Nominal optical power output1.122 mW
minimum return loss-27 dB
Base Number Matches1
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Can uCOS-II 51 be simulated on PROTUES?  
Can uCOS-II 51 be simulated on PROTUES? What should I pay attention to? Thank you!...
howard_lewes Real-time operating system RTOS
Help, analysis of the load detection principle of mobile power supply
I have a power bank with a single TP4201b main control unit and load detection. That is, it will only boost the voltage for charging when a load is connected. If there is no load, the boost will stop ...
ghdnui Power technology
Unable to enter external interrupt
I would like to ask the seniors to help look at my interrupt setting function. Why can't I enter the external interrupt? EXTI_SWINT_Enable (EXTI_LINE1) is set to generate a software interrupt and it c...
wu594127 ARM Technology
The role of each layer in the Gerber file when making a steel mesh
1) The size of the pads of the patch layer and the circuit layer is consistent with the size of the pads of the bare copper of the physical PCB. This is the basis for the size of the opening (a necess...
szjlczhang PCB Design
The follower output is amplified, please advise
]The previous one is a RC attenuation circuit. When the attenuation is 100 times, the follower output is normal, but when the attenuation is 10 times, the follower output is amplified. 10M bandwidth i...
cwshantang Analog electronics
The weekly review information is here~ The fresh delivery is here
Last week, the TI evaluation was launched. This week, our Lingdong Microelectronics eminiboard evaluation is also about to be launched. Many evaluation reports have been released this week. Come and h...
okhxyyo Special Edition for Assessment Centres

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2159  1199  1924  2131  608  44  25  39  43  13 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号